B1851
SUPPLEMENTAL RESTRAINT SYSTEM: AIRBAG SYSTEM: B1850/62: Short in Rear Driver Side - Side Squib Circuit
DTC B1850/62 - Short in Rear Driver Side - Side Squib Circuit
DTC B1851/62 - Open in Rear Driver Side - Side Squib Circuit
DTC B1852/62 - Short to GND in Rear Driver Side - Side Squib Circuit
DTC B1853/62 - Short to B+ in Rear Driver Side - Side Squib Circuit
DESCRIPTION
The rear driver side - side squib circuit consists of the center airbag sensor assembly and the rear seat side airbag assembly LH.
This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the rear driver side - side squib circuit.
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
- Perform the simulation method by selecting "check mode" (signal check) with Techstream Check Mode Procedure.
- After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road Check Mode Procedure.
PROCEDURE
1. CHECK REAR SEAT SIDE AIRBAG ASSEMBLY LH (REAR DRIVER SIDE - SIDE SQUIB)
(a) Turn the engine switch off.
(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(c) Disconnect the connector from the rear seat side airbag assembly LH.
(d) Connect SST (resistance 2.1 Ohms) to connector C.
CAUTION:
Never connect a tester to the rear seat side airbag assembly RH (rear driver side - side squib) for measurement, as this may lead to a serious injury due to airbag deployment.
NOTICE:
- Do not forcibly insert SST into the terminals of the connector when connecting.
- Insert straight SST into the terminals of the connector.
SST: 09843-18061
(e) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(f) Turn the engine switch on (IG), and wait for at least 60 seconds.
(g) Clear the DTCs stored in the memory DTC Check / Clear.
(h) Turn the engine switch off.
(i) Turn the engine switch on (IG), and wait for at least 60 seconds.
(j) Check the DTCs DTC Check / Clear.
OK:
DTC B1850, B1851, B1852, B1853, or 62 is not output.
HINT: Codes other than DTC B1850, B1851, B1852, B1853, and 62 may be output at this time, but they are not related to this check.
OK -- REPLACE REAR SEAT SIDE AIRBAG ASSEMBLY LH
NG -- Continue to next step.
2. CHECK FLOOR WIRE (REAR DRIVER SIDE - SIDE SQUIB CIRCUIT)
(a) Turn the engine switch off.
(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(c) Disconnect SST from connector C.
(d) Disconnect the connectors from the center airbag sensor assembly.
(e) Check the short to B+ in the circuit.
(1) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(2) Turn the engine switch on (IG).
(3) Measure the voltage according to the value(s) in the table below.
Standard voltage:
(f) Check the open in the circuit.
(1) Turn the engine switch off.
(2) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(3) Measure the resistance according to the value(s) in the table below.
Standard resistance:
(g) Check the short to ground in the circuit.
(1) Measure the resistance according to the value(s) in the table below.
Standard resistance:
(h) Check the short in the circuit.
(1) Release the activation prevention mechanism built into connector B Diagnosis System.
(2) Measure the resistance according to the value(s) in the table below.
Standard resistance:
NG -- REPAIR OR REPLACE FLOOR WIRE
OK -- Continue to next step.
3. CHECK CENTER AIRBAG SENSOR ASSEMBLY
(a) Restore the released activation prevention mechanism of connector B to the original condition.
(b) Connect the connectors to the rear seat side airbag assembly LH and the center airbag sensor assembly.
(c) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(d) Turn the engine switch on (IG), and wait for at least 60 seconds.
(e) Clear the DTCs stored in the memory DTC Check / Clear.
(f) Turn the engine switch off.
(g) Turn the engine switch on (IG), and wait for at least 60 seconds.
(h) Check the DTCs DTC Check / Clear.
OK:
DTC B1850, B1851, B1852, B1853, or 62 is not output.
HINT: Codes other than DTC B1850, B1851, B1852, B1853, and 62 may be output at this time, but they are not related to this check.
NG -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK -- USE SIMULATION METHOD TO CHECK