B1000

SUPPLEMENTAL RESTRAINT SYSTEM: AIRBAG SYSTEM: B1000/31: Center Airbag Sensor Assembly Malfunction

DTC B1000/31 - Center Airbag Sensor Assembly Malfunction

DESCRIPTION

The center airbag sensor consists of the airbag sensor, the safing sensor, the drive circuit, the diagnosis circuit, the ignition control, etc.
If the center airbag sensor receives signals from the airbag sensor, it determines whether or not the SRS should be activated.
DTC B1000/31 is recorded when a malfunction is detected in the center airbag sensor.





HINT: When a malfunction code is displayed simultaneously with B1000/31, repair the malfunction indicated by that code first.

WIRING DIAGRAM





INSPECTION PROCEDURE

PROCEDURE

1. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO B+)
(a) Turn the power switch OFF.
(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.




(c) Disconnect the K44 center airbag sensor connector and the A1 front airbag sensor LH connector.
(d) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(e) Turn the power switch ON (IG).
(f) Measure the voltage according to the value(s) in the table below.
Standard voltage:






NG -- CHECK ENGINE ROOM MAIN WIRE (SHORT TO B+)
OK -- Continue to next step.
2. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT)




(a) Turn the power switch OFF.
(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(c) Disconnect the K44 center airbag sensor connector and the A1 front airbag sensor LH connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard resistance:






NG -- CHECK ENGINE ROOM MAIN WIRE (SHORT)
OK -- Continue to next step.
3. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO GROUND)




(a) Measure the resistance according to the value(s) in the table below.
Standard resistance:






NG -- CHECK ENGINE ROOM MAIN WIRE (SHORT TO GROUND)
OK -- Continue to next step.
4. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO B+)




(a) Disconnect the A25 connector from the front airbag sensor RH.
(b) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(c) Turn the power switch ON (IG).
(d) Measure the voltage according to the value(s) in the table below.
Standard voltage:






NG -- CHECK ENGINE ROOM MAIN WIRE (SHORT TO B+)
OK -- Continue to next step.
5. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT)




(a) Turn the power switch OFF.
(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:






NG -- CHECK ENGINE ROOM MAIN WIRE (SHORT)
OK -- Continue to next step.
6. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO GROUND)




(a) Measure the resistance according to the value(s) in the table below.
Standard resistance:






NG -- CHECK ENGINE ROOM MAIN WIRE (SHORT TO GROUND)
OK -- Continue to next step.
7. CHECK CENTER AIRBAG SENSOR ASSEMBLY




(a) Connect the connectors to the center airbag sensor, front airbag sensor LH and RH.
(b) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(c) Turn the power switch ON (IG), and wait for at least 60 seconds.
(d) Clear the DTCs stored in memory DTC Check / Clear.
(e) Turn the power switch OFF.
(f) Turn the power switch ON (IG), and wait for at least 60 seconds.
(g) Check the DTCs DTC Check / Clear.
OK:
DTC B1000/31 is not output.
NG -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK -- USE SIMULATION METHOD TO CHECK
8. CHECK ENGINE ROOM MAIN WIRE (SHORT TO B+)




(a) Turn the power switch OFF.
(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(c) Disconnect the engine room main wire connector from the instrument panel wire.
(d) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(e) Turn the power switch ON (IG).
(f) Measure the voltage according to the value(s) in the table below.
Standard voltage:






NG -- REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK -- REPAIR OR REPLACE INSTRUMENT PANEL WIRE
9. CHECK ENGINE ROOM MAIN WIRE (SHORT)




(a) Disconnect the engine room main wire connector from the instrument panel wire.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:






NG -- REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK -- REPAIR OR REPLACE INSTRUMENT PANEL WIRE
10. CHECK ENGINE ROOM MAIN WIRE (SHORT TO GROUND)




(a) Disconnect the engine room main wire connector from the instrument panel wire.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:






NG -- REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK -- REPAIR OR REPLACE INSTRUMENT PANEL WIRE
11. CHECK ENGINE ROOM MAIN WIRE (SHORT TO B+)




(a) Turn the power switch OFF.
(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(c) Disconnect the engine room main wire connector from the instrument panel wire.
(d) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(e) Turn the power switch ON (IG).
(f) Measure the voltage according to the value(s) in the table below.
Standard voltage:






NG -- REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK -- REPAIR OR REPLACE INSTRUMENT PANEL WIRE
12. CHECK ENGINE ROOM MAIN WIRE (SHORT)




(a) Disconnect the engine room main wire connector from the instrument panel wire.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:






NG -- REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK -- REPAIR OR REPLACE INSTRUMENT PANEL WIRE
13. CHECK ENGINE ROOM MAIN WIRE (SHORT TO GROUND)




(a) Disconnect the engine room main wire connector from the instrument panel wire.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:






NG -- REPAIR OR REPLACE ENGINE ROOM MAIN WIRE
OK -- REPAIR OR REPLACE INSTRUMENT PANEL WIRE