Door Courtesy Light Circuit
LIGHTING: LIGHTING SYSTEM: Door Courtesy Light Circuit
Door Courtesy Light Circuit
DESCRIPTION
The door courtesy light turns on when the door is opened and turns off when closed.
WIRING DIAGRAM
INSPECTION PROCEDURE
PROCEDURE
1. CHECK OPERATION OF COURTESY LIGHT AND OUTER SCUFF LIGHT
(a) When a door is opened, check that the following lights illuminate.
Result
D -- PERFORM ACTIVE TEST USING TECHSTREAM (COURTESY LIGHT)
C -- PERFORM ACTIVE TEST USING TECHSTREAM (COURTESY LIGHT)
B -- PERFORM ACTIVE TEST USING TECHSTREAM (COURTESY LIGHT)
A -- Continue to next step.
2. PERFORM ACTIVE TEST USING TECHSTREAM (COURTESY LIGHT)
(a) Select the ACTIVE TEST, use the Techstream to generate a control command, and then check that the courtesy light illuminates.
Driver Door (Front multiplex network door ECU LH)
Result
C -- PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
B -- REPLACE FRONT DOOR OUTER SCUFF LIGHT LH
A -- Continue to next step.
3. REPLACE FRONT DOOR COURTESY LIGHT LH
(a) Temporarily replace the front door courtesy light LH with a new or normally functioning one.
(b) Check that the courtesy light illuminates.
OK:
Courtesy light illuminates.
OK -- END
NG -- Continue to next step.
4. CHECK WIRE HARNESS (FRONT DOOR ECU LH - FRONT DOOR COURTESY LIGHT LH)
(a) Disconnect the M9 ECU connector.
(b) Disconnect the Q15 light connector.
(c) Measure the resistance of the wire harness side connectors.
Standard resistance:
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
5. REPLACE FRONT DOOR OUTER SCUFF LIGHT LH
(a) Temporarily replace the front door outer scuff light LH with a new or normally functioning one.
(b) Check that the outer scuff light illuminates.
OK:
Outer scuff light illuminates.
OK -- END
NG -- Continue to next step.
6. CHECK WIRE HARNESS (FRONT DOOR ECU LH - FRONT DOOR OUTER SCUFF LIGHT LH)
(a) Disconnect the M9 ECU connector.
(b) Disconnect the Q14 light connector.
(c) Measure the resistance of the wire harness side connectors.
Standard resistance:
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
7. PERFORM ACTIVE TEST USING TECHSTREAM (COURTESY LIGHT)
(a) Select the ACTIVE TEST, use the Techstream to generate a control command, and then check that the courtesy light (front door RH) illuminates.
Passenger Door (Front multiplex network door ECU RH)
Result
C -- PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
B -- REPLACE FRONT DOOR OUTER SCUFF LIGHT RH
A -- Continue to next step.
8. REPLACE FRONT DOOR COURTESY LIGHT RH
(a) Temporarily replace the front door courtesy light RH with a new or normally functioning one.
(b) Check that the courtesy light illuminates.
OK:
Courtesy light illuminates.
OK -- END
NG -- Continue to next step.
9. CHECK WIRE HARNESS (FRONT DOOR ECU RH - FRONT DOOR COURTESY LIGHT RH)
(a) Disconnect the M4 ECU connector.
(b) Disconnect the Q8 light connector.
(c) Measure the resistance of the wire harness side connectors.
Standard resistance:
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
10. REPLACE FRONT DOOR OUTER SCUFF LIGHT RH
(a) Temporarily replace the outer scuff light (front door RH) with a new or normally functioning one.
(b) Check that the outer scuff light illuminates.
OK:
Outer scuff light illuminates.
OK -- END
NG -- Continue to next step.
11. CHECK WIRE HARNESS (FRONT DOOR ECU RH - FRONT DOOR OUTER SCUFF LIGHT RH)
(a) Disconnect the M4 ECU connector.
(b) Disconnect the Q7 light connector.
(c) Measure the resistance of the wire harness side connectors.
Standard resistance:
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
12. PERFORM ACTIVE TEST USING TECHSTREAM (COURTESY LIGHT)
(a) Select the ACTIVE TEST, use the Techstream to generate a control command, and then check that the courtesy light illuminates.
Rear Left Door (Rear multiplex network door ECU LH)
OK -- PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG -- Continue to next step.
13. REPLACE REAR DOOR COURTESY LIGHT LH
(a) Temporarily replace the rear door courtesy light LH with a new or normally functioning one.
(b) Check that the courtesy light illuminates.
OK:
Courtesy light illuminates.
OK -- END
NG -- Continue to next step.
14. CHECK WIRE HARNESS (REAR DOOR ECU LH - REAR DOOR COURTESY LIGHT LH)
(a) Disconnect the O7 ECU connector.
(b) Disconnect the S6 light connector.
(c) Measure the resistance of the wire harness side connectors.
Standard resistance:
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
15. PERFORM ACTIVE TEST USING TECHSTREAM (COURTESY LIGHT)
(a) Select the ACTIVE TEST, use the Techstream to generate a control command, and then check that the courtesy light illuminates.
Rear Right Door (Rear multiplex network door ECU RH)
OK -- PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG -- Continue to next step.
16. REPLACE REAR DOOR COURTESY LIGHT RH
(a) Temporarily replace the rear door courtesy light RH with a new or normally functioning one.
(b) Check that the courtesy light illuminates.
OK:
Courtesy light illuminates.
OK -- END
NG -- Continue to next step.
17. CHECK WIRE HARNESS (REAR DOOR ECU RH - REAR DOOR COURTESY LIGHT RH AND BODY GROUND)
(a) Disconnect the O3 ECU connector.
(b) Disconnect the S2 light connector.
(c) Measure the resistance of the wire harness side connectors.
Standard resistance:
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE