Distance Sensor: Adjustments

CRUISE CONTROL: MILLIMETER WAVE RADAR SENSOR: ADJUSTMENT

1. ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY

Text in Illustration

CAUTION:
Exposure to radio frequency emissions is hazardous to your health. It is hazardous to your health to be within 20 cm (7.87 in.) of the device's radio frequency aperture.

NOTICE:
* This device complies with FCC radio frequency emission regulations.
* Perform measurements on a level surface.
* Make sure that no large pieces of metal are within a 10 m (32.8 ft.) x 14 m (45.9 ft.) area in front of the vehicle. If possible, the surrounding area should also be free of large metal objects.
(a) Before adjusting the radar beam axis, prepare the vehicle as follows.

(1) Check the tire pressure and adjust it if necessary.

(2) Remove all excess weight from the vehicle (luggage, heavy objects, etc.).

(b) Check and adjust the vertical direction of the radar sensor.

Text in Illustration

(1) Remove dust, oil and foreign matter from the radar sensor's level rack.

(2) Set a level on the radar sensor's level rack.

(3) Check that the level's air bubble is within the red frame.

Text in Illustration

OK:

Level's air bubble is within the red frame.

(3) If the bubble is not within the red frame, use a screwdriver to adjust bolt A until the air bubble is within the red frame.

HINT
* The adjustable range within the level's red frame is +/- 0.2°.
* The target angle is +0.2° (upward angle of 0.2°).

Adjustment:

Text in Illustration

(1) Adjust the reflector so that the center of SST reflector is the same height as the millimeter wave radar sensor.

SST : 09870-60000

09870-60010

SST : 09870-60040

HINT
Prepare a 10 m (32.8 ft.) string, string with a sharp-pointed weight (plumb bob), and 5 m (16.4 ft.) tape measure.

(d) Place the reflector.

(1) Hang the string (with weight) from the center of the vehicle's rear emblem. Mark the vehicle's rear center point on the ground. Repeat for the front of the vehicle.

(2) Set one end of the 10 m (32.8 ft.) string on the vehicle's rear center point. Run the string over the vehicle's front center point to a position 5 m (16.4 ft.) beyond the vehicle's front center point, as shown in the illustration. Mark the 5 m (16.4 ft.) position.

(3) Using a tape measure, measure 16.5 mm (0.65 in.) to the right of the 5 m (16.4 ft.) position. Place the reflector at that position.

NOTICE:
Perform the operation as precisely as possible.

Text in Illustration

(e) Check the radar beam axis.

(1) When using the Techstream:

1 Connect the Techstream to the DLC3.

2 Turn the power switch on (IG).

3 Turn the Techstream on, and turn the cruise control main switch on.

4 Select "Connect to Vehicle".

5 Select each item on the display screen and proceed to the next screen.

6 Under "System Selection Menu", select "Radar Cruise".

7 Select "Utility".

8 Select "Beam Axis Adjustment" and proceed to the next screen.

HINT
A buzzer will sound for 1 second.

9 Follow the Techstream display, and continue with the adjustment.

CAUTION:
Do not come within 20 cm (7.87 in.) of the radar sensor.

NOTICE:
* Turn the cruise control main switch on before pressing "Next".
* Make sure there is at least 20 cm (7.87 in.) between the radar sensor and any nearby individuals.
(2) Check the following items on the radar cruise divergence data screen.

NOTICE:
While using the Techstream beam axis adjustment mode, the actual direction and angle of the radar sensor may be different from the Techstream data. In such a case, the deviation is displayed on the multi-information display in the combination meter.

1 Confirm that the distance value is approximately 5 m (16.4 ft.).

HINT
* A value between 0.0 m (0.0 ft.) and 6.3 m (20.7 ft.) should be indicated.
* If the distance is 0.0 m (0.0 ft.), the sensor cannot detect the target. Reconfirm that there is no metal in the specified area in front of the vehicle (refer to the Notice at the beginning of this adjustment procedure).
2 Confirm that the left/right side value is between 0.0 m (0.0 ft.) and 6.3 m (20.7 ft.).

HINT
If the distance is 0.0 m (0.0 ft.), the sensor cannot detect the target. Reconfirm that there is no metal in the specified area in front of the vehicle (refer to the Notice at the beginning of this adjustment procedure).

(f) Check and adjust the horizontal direction of the radar sensor.

(1) Check that the divergence of the radar beam axis is 0°.

Standard:

0° (Both right and left)

(1) If the axis is not as specified, use a screwdriver to adjust bolt B until the divergence of the radar beam axis is 0°.

(2) Based on the measured divergence of the beam axis, turn and adjust bolt B for horizontal adjustment of the millimeter wave radar sensor using a screwdriver.

Text in Illustration

Adjustment:

HINT
* If "LEFT SIDE: 1.0°" is displayed, the divergence is 1.0° in the left direction. Turn bolt B approximately 2.5 turns to the negative (-) side.
* If the value does not change to 0°, it is possible that the sensor is aiming at something different. Reconfirm that there are no reflective materials in the surrounding area.
(3) Select "Next". The driving learning value is automatically reset.

HINT
A buzzer will sound for 10 seconds or more.

(4) Disconnect the Techstream from the DLC3.

(g) Recheck and readjust the vertical direction of the radar sensor.

(1) Set a level on the radar sensor's level rack.

Text in Illustration

(2) Check that the level's air bubble is within the red frame.

Text in Illustration

OK:

Level's air bubble is within the red frame.

(2) If the bubble is not within the red frame, use a screwdriver to adjust bolt A until the level's air bubble is within the red frame.

HINT
* The adjustable range within the red frame is +/- 0.2°.
* The target angle is + 0.2° (upward angle of 0.2°).

Adjustment: