Removal

BRAKE (REAR): REAR BRAKE: REMOVAL

NOTICE:
* When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.
* While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch is turned on. Therefore, even if only brake pads are to be removed and installed, be sure to perform the Disable Brake Control procedure and disconnect the cable from the negative (-) terminal of the auxiliary battery before beginning work.

HINT
* Use the same procedure for the LH side and RH side.
* The following procedure is for the LH side.

1. PRECAUTION

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work Service Precautions.

2. DISABLE BRAKE CONTROL Removal

3. REMOVE REAR WHEEL

4. DRAIN BRAKE FLUID

NOTICE:
If brake fluid leaks onto any painted surface, immediately wash it off.

5. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY Removal

6. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH Removal

7. REMOVE INSTRUMENT SIDE PANEL LH Removal

8. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY Removal

9. LOOSEN PARKING BRAKE CABLE

(a) Completely release the parking brake pedal.

(b) Loosen the lock nut and adjusting nut to completely release the parking brake cable.

Text in Illustration

10. REMOVE PARKING BRAKE LEVER PROTECTOR Removal

11. DISCONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

(a) Remove the bolt and separate the No. 3 parking brake cable assembly.

(b) Separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.

Text in Illustration

HINT
Insert an offset wrench (14 mm) at the base of the No. 3 parking brake cable assembly as shown in the illustration to disengage the clip. Pull out the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.

12. SEPARATE REAR FLEXIBLE HOSE

(a) Remove the union bolt and gasket, and separate the rear flexible hose from the rear disc brake cylinder assembly.

13. REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY

(a) Hold the rear disc brake pad guide pin, and remove the 2 bolts and rear disc brake cylinder assembly.

Text in Illustration

NOTICE:
Remove the rear disc brake cylinder assembly while holding both of the rear disc brake pads because the anti-squeal springs may fall off the rear disc brake pads.

14. REMOVE REAR DISC BRAKE PAD

(a) Remove the 2 anti-squeal springs from the rear disc brake pads.

(b) Remove the 2 rear disc brake pads from the disc brake cylinder mounting.

15. REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM

(a) Remove the rear No. 1 disc brake anti-squeal shim and rear No. 2 disc brake anti-squeal shim from each rear disc brake pad.

Text in Illustration

16. REMOVE REAR DISC BRAKE PAD SUPPORT PLATE

(a) Remove the 2 rear disc brake pad support plates from the disc brake cylinder mounting.

NOTICE:
Each rear disc brake pad support plate has a different shape. Be sure to put an identification mark on each rear disc brake pad support plate so that it can be reinstalled to its original position.

17. REMOVE REAR DISC BRAKE PAD GUIDE PIN

(a) Remove the 2 rear disc brake pad guide pins from the disc brake cylinder mounting.

18. REMOVE REAR DISC BRAKE BUSHING DUST BOOT

(a) Remove the 2 rear disc brake bushing dust boots from the disc brake cylinder mounting.

19. REMOVE DISC BRAKE CYLINDER MOUNTING

(a) Remove the 2 bolts and disc brake cylinder mounting.

20. REMOVE REAR DISC

(a) Put matchmarks on the disc and the axle hub.

Text in Illustration

(b) Remove the rear disc.