Removal

ENGINE HOOD / DOOR: FRONT DOOR: REMOVAL

HINT
* Use the same procedures for the RH side and LH side.
* The procedures listed below are the LH side.

1. REMOVE DOOR INSIDE HANDLE BEZEL

(a) Using a screwdriver, detach the 3 claws and remove the 3 claws and remove the bezel plug.

HINT
Tape the screwdriver tip before use.

2. REMOVE FRONT DOOR TRIM PANEL ASSEMBLY

(a) Detach the 2 claws and remove the trim lower cover.

(b) Disconnect the connector.

(c) Remove the 2 screws.

(d) Remove the 9 clips and trim cover.

(e) Disconnect the 2 cables from the inside handle.

3. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

(a) Remove the 4 screws and inside handle.

4. REMOVE INTERIOR ILLUMINATION LIGHT ASSEMBLY NO.1

(a) Detach the 2 claws, disconnect the connector and then remove the light.

5. REMOVE FRONT DOOR COURTESY LIGHT ASSEMBLY

Detach the 4 claws and remove lens from the courtesy light.

Detach the 2 claws and remove courtesy light from the door trim panel.

(a) Disconnect the connector.

6. REMOVE SEAT MEMORY SWITCH

(a) Disconnect the connector.

(b) Remove the 2 screws and switch from the door trim panel.

7. REMOVE FRONT DOOR WEATHERSTRIP NO.3

(a) Remove the 4 clips and weatherstrip from the door.

8. REMOVE FRONT DOOR TRIM COVER

(a) Remove the screw.

(b) Using a clip remover, detach the 6 clips.

9. REMOVE MULTIPLEX NETWORK SWITCH ASSEMBLY

(a) Disconnect the connector.

(b) Remove the 3 screws and network switch.

10. REMOVE DOOR FRAME GARNISH

(a) Remove the screw.

(b) Using a screwdriver, remove the 2 clips and garnish.

HINT
Tape the screwdriver tip before use.

11. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY Removal

12. REMOVE FRONT DOOR GLASS WEATHERSTRIP INNER

(a) Remove the weatherstrip inner by pulling it upward in the direction indicated the arrow in the illustration.

13. REMOVE MULTIPLEX NETWORK DOOR ECU FRONT

(a) Remove the 2 screws and ECU.

(b) Disconnect the 3 connectors.

14. REMOVE FRONT DOOR SERVICE HOLE COVER

(a) Remove the 2 bolts and door armrest bracket.

(b) Remove the service hole cover.

HINT
Remove the remaining tape on the door.

15. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

(a) Driver's side:

Temporarily install the multiplex network master switch.

(b) Passenger's side:

Temporarily install the multiplex network switch.

(c) Move the door glass until the bolts appear in the service holes.

(d) Remove the 2 bolts.

HINT
Be careful when removing the bolts as the glass may fall and become damaged.

Remove the door glass in the direction indicated by the arrows in the illustration.

HINT
Remove the glass upward.

NOTICE:
Be careful not to damage the glass.

(e) Driver's side:

Remove the multiplex network master switch.

(f) Passenger's side:

Remove the multiplex network switch.

16. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY

17. REMOVE FRONT DOOR WINDOW FRAME MOULDING REAR

18. REMOVE FRONT DOOR WINDOW FRAME MOULDING UPPER

19. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY

(a) Disconnect the connector.

(b) Remove the 6 bolts and window regulator.

HINT
Remove the window regulator through the service hole.

NOTICE:
Be careful when removing the bolts as the window regulator may fall and become damaged.

20. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY

(a) Using a T25 "torx" driver, remove the 3 screws and motor.

HINT
Be careful when removing the screws as the motor may fall and become damaged.

21. REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

(a) Remove the 2 bolts and frame.

HINT
Remove the frame through the service hole.

NOTICE:
Be careful when removing the bolts as the frame may fall and become damaged.

22. REMOVE FRONT DOOR OUTSIDE HANDLE COVER

(a) Remove the hole plug.

(b) Using a T30 "torx" wrench, loosen the screw and remove the cover with the door lock key cylinder installed.

(c) Remove the cylinder from the cover.

23. REMOVE FRONT DOOR HANDLE ASSEMBLY OUTSIDE

(a) Disconnect the connector.

(b) Remove the handle by sliding and pulling it in the direction indicated by the arrow mark in the illustration.

NOTICE:
If the release plate is not pulled and held when removing the handle, the release plate will interfere with the handle and become damaged.

(c) Remove the outside handle pad front and rear.

24. REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD

(a) Detach the 2 claws and remove the pad.

25. REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD

(a) Detach the 2 claws and remove the pad.

26. REMOVE FRONT DOOR WITH MOTOR LOCK ASSEMBLY

(a) Disconnect the door lock connector.

(b) Using a T30 "torx" wrench, remove the 3 screws and door lock.

HINT
Remove the door lock through the service hole.

NOTICE:
Be careful when removing the bolts as the door lock may fall and become damaged.

27. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

Detach the connector.

(a) Using a T30 "torx" wrench, loosen the screw.

(b) Slide the outside handle frame to remove it.

HINT
Remove the outside handle frame through the service hole.

(a) Remove the 2 bolts and cushion.

29. REMOVE FRONT DOOR CHECK ASSEMBLY

(a) Remove the cover.

(b) Remove the bolt, 2 nuts and door check.

HINT
Remove the door check through the service hole.

NOTICE:
Be careful when removing the bolts as the door check may fall and become damaged.

30. REMOVE FRONT DOOR WEATHERSTRIP

(a) Using a clip remover, detach the clips and remove the weatherstrip.

HINT
If clips are damaged during removal, replace them.

31. REMOVE FRONT DOOR WIRE

(a) Disconnect the wire clips.

(b) Remove the 2 bolts and door wire.