Operation Check

DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM: OPERATION CHECK

1. CHECK ELECTRICAL DOOR LOCK OPERATION

NOTICE:
The initial condition that the customizing function using the Techstream is not chosen is shown.

(a) Check the basic function.

(1) Check that all doors lock when the door control switch (for manual operation) is turned to LOCK and all doors unlock when turned to UNLOCK.

(2) Check that all doors lock when the driver side door lock key cylinder is turned to LOCK using the mechanical key.

(b) Check the electrical key lock-in prevention function.

NOTICE:
In order to prevent the electrical key from being actually locked-in, the following inspection should be performed with the driver side door window open.

(1) Place the electrical key inserted in the cabin.

(2) With the driver side door open, check that all doors unlock immediately after the door lock knob for the driver side door is turned to LOCK.

(3) With the driver side door open, check that all doors unlock immediately after the door control switch (for manual operation) is turned to LOCK.

(4) With the driver side door open, turn the driver side door lock knob to LOCK and hold it for 2 seconds or more, and then close the driver side door. Then check that all doors unlock.

(c) Check the security function.

(1) Close all doors with the driver side door window open so that the door control switch can be operated from outside the vehicle.

(2) Pull out the electrical key, open the driver side door and then close and lock the door using the electrical key. Under this condition, check that all doors do not unlock when the door control switch (for manual operation) is turned to UNLOCK from outside the vehicle.

(3) Pull out the electrical key and the mechanical key, and close and lock the driver side door by mechanical key operation. Under this condition, check that all doors do not unlock when the door control switch (for manual operation) is turned to UNLOCK from outside the vehicle.

(4) Pull out the electrical key, close the driver side door, and lock the door by wireless door lock operation. Under this condition, check that all doors do not unlock when the door control switch (for manual operation) is turned to UNLOCK from outside the vehicle.

HINT
Check that the security function is canceled under the following conditions:

* The engine switch is turned on (IG).
* The driver side door is unlocked using the mechanical key or the electrical key.
* The door control switch (for manual operation) is turned to UNLOCK after the door control knob is turned to UNLOCK manually.

(d) Check the illumination function.

(1) Set the room light switch to the DOOR position.

(2) With all doors locked, check that all doors unlock when the driver side door lock cylinder is turned to UNLOCK using the key. At the same time, the room light and the foot light come on.

(3) Check that the room light and the foot light go off in approximately 15 seconds if the doors have not been opened.

(e) Check the AUTO lock function.

(1) Lock all doors.

(2) Unlock all doors using the electrical key.

(3) Allow 30 seconds to elapse while all doors remain closed and the electrical key switch and the entry unlock switch remain untouched. Then, check that all doors will lock automatically.

(f) Check the key-linked 2-step unlock function.

(1) Lock all doors.

(2) Check that only the driver door unlocks when the driver door lock cylinder is turned to unlock once using the key and other doors unlock when turned to unlock consecutively once again.

(g) Check the driver door-linked automatic door unlock function.

HINT
The default setting for A/T is OFF. If necessary, the function must be set to ON through the customize function.

(1) When the driver door is closed, turning the engine switch from on (IG) to off and opening the driver door within 10 seconds will automatically unlock all doors.

(h) Check the shift linked automatic door lock function (for A/T).

HINT
* The default setting for models without the occupant classification system is OFF. If necessary, the function must be set to ON through the customize function.
* The automatic locking operation is disabled if the crash detection sensor (built into the center airbag sensor) unlocking system malfunctions when the engine switch is on (IG) and all doors are closed.

(1) When the engine switch is on (IG) and the shift lever is moved from P to any position other than P, check that all doors lock automatically.

(i) Check the shift linked automatic door unlock function (for A/T).

(1) When the engine switch is on (IG) and the shift lever is moved to P from any position other than P, check that all doors unlock automatically.

(j) Check the speed-sensitive automatic door lock function.

HINT
* The default setting for models with the occupant classification system and A/T is OFF. If necessary, the function must be set to ON through the customize function.
* The automatic locking operation is disabled if the crash detection sensor (built into the center airbag sensor) unlocking system has a malfunction when the engine switch is on (IG) and all doors are closed.

(1) When any door is unlocked and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that all doors lock automatically.