Installation
4GR-FSE ENGINE CONTROL: AIR FUEL RATIO SENSOR: INSTALLATION
1. INSTALL AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)
(a) Using SST, install the air fuel ratio sensor (for Bank 2 Sensor 1) to the exhaust manifold LH.
SST : 09224-00010
without SST - Torque : 44 Nm (449 kgf-cm, 32 ft-lbf)
with SST - Torque : 40 Nm (408 kgf-cm, 30 ft-lbf)
NOTICE:
* The "with SST" torque value is effective when using SST with a fulcrum length of 30 mm (1.18 in.).
* The "with SST" torque value is effective when using a torque wrench with a fulcrum length of 300 mm (11.81 in.) Service Precautions.
* This torque value is effective when SST is parallel to the torque wrench.
2. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH Installation
3. INSTALL NO. 3 ENGINE ROOM RELAY BLOCK ASSEMBLY Installation
4. INSTALL AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)
(a) Using SST, install the air fuel ratio sensor connector (for Bank 1 Sensor 1) to the exhaust manifold RH.
SST : 09224-00010
without SST - Torque : 44 Nm (449 kgf-cm, 32 ft-lbf)
with SST - Torque : 40 Nm (408 kgf-cm, 30 ft-lbf)
NOTICE:
* The "with SST" torque value is effective when using SST with a fulcrum length of 30 mm (1.18 in.).
* The "with SST" torque value is effective when using a torque wrench with a fulcrum length of 300 mm (11.81 in.).
* This torque value is effective when SST is parallel to the torque wrench.
(b) Connect the 2 clamps and air fuel ratio sensor connector (for Bank 1 Sensor 1).
5. INSTALL NO. 4 ENGINE WIRE
(a) Connect the connector and install the 2 clamps.
(b) Connect the No. 1 engine wire to the engine room No. 1 junction block. Then, install it with the nut.
Torque : 12 Nm (124 kgf-cm, 9 ft-lbf)
(c) Install the engine room No. 1 relay block cover.
6. INSTALL BATTERY TRAY
(a) Install the battery tray with the 3 bolts.
Torque : 5.4 Nm (55 kgf-cm, 48 in-lbf)
7. INSTALL POWER STEERING ECU ASSEMBLY
(a) Install the power steering ECU assembly Installation.
8. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE Installation
9. INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET SUB-ASSEMBLY (for Automatic Transmission) Installation
10. INSTALL FRONT EXHAUST PIPE ASSEMBLY Installation
11. INSTALL FRONT CENTER FLOOR BRACE Installation
12. INSTALL REAR BODY SUPPORT BRACKET Installation
13. INSTALL NO. 2 ENGINE UNDER COVER
14. INSTALL NO. 1 BODY MOUNTING BRACKET SUB-ASSEMBLY LH Installation
15. INSTALL NO. 1 BODY MOUNTING BRACKET SUB-ASSEMBLY RH Installation
16. INSTALL NO. 2 FLOOR UNDER COVER Installation
17. INSTALL NO. 1 FLOOR UNDER COVER Installation
18. INSTALL FRONT FLOOR COVER LH Installation
19. INSTALL FRONT FLOOR COVER RH Installation
20. INSTALL ENGINE UNDER COVER
21. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
22. INSPECT FOR EXHAUST GAS LEAK
23. INSTALL V-BANK COVER SUB-ASSEMBLY Installation
24. INSTALL ENGINE ROOM SIDE COVER LH Installation
25. INSTALL ENGINE ROOM SIDE COVER Installation
26. INSTALL COOL AIR INTAKE DUCT SEAL Installation