Removal

2GR-FSE LUBRICATION: OIL PUMP: REMOVAL

1. REMOVE COOL AIR INTAKE DUCT SEAL Removal

2. REMOVE ENGINE ROOM SIDE COVER LH Removal

3. REMOVE ENGINE ROOM SIDE COVER RH Removal

4. REMOVE V-BANK COVER SUB-ASSEMBLY Removal

5. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM Service and Repair

6. DISCHARGE FUEL SYSTEM PRESSURE

Service Precautions

7. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

8. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

9. REMOVE FRONT WHEEL

10. REMOVE ENGINE UNDER COVER

11. REMOVE NO. 2 ENGINE UNDER COVER (for 2WD)

12. REMOVE ENGINE UNDER COVER REAR LH (for 2WD) Removal

13. REMOVE ENGINE UNDER COVER REAR RH (for 2WD) Removal

14. DRAIN ENGINE OIL Replacement

15. DRAIN ENGINE COOLANT Testing and Inspection

16. DRAIN DIFFERENTIAL OIL (for 4WD) Removal

17. REMOVE FRONT EXHAUST PIPE ASSEMBLY

Removal

18. REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

Removal for 2WD)

Removal for 4WD)

19. REMOVE NO. 1 INLET AIR CLEANER Removal

20. REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE Removal

21. REMOVE AIR CLEANER CASE SUB-ASSEMBLY Removal

22. DISCONNECT UNION TO CHECK VALVE HOSE Removal

23. DISCONNECT NO. 2 FUEL VAPOR FEED HOSE Removal

24. DISCONNECT INLET RADIATOR HOSE Removal

25. DISCONNECT OUTLET RADIATOR HOSE Removal

26. DISCONNECT RADIATOR RESERVOIR TANK HOSE Removal

27. DISCONNECT INLET HEATER WATER HOSE Removal

28. DISCONNECT OUTLET HEATER WATER HOSE Removal

29. REMOVE NO. 1 COOLER REFRIGERANT SUCTION HOSE Removal

30. REMOVE DISCHARGE HOSE SUB-ASSEMBLY Removal

31. REMOVE ECM COVER Removal

32. DISCONNECT ENGINE WIRE Removal

33. DISCONNECT FUEL MAIN TUBE

Service Precautions

34. DISCONNECT NO. 3 FUEL HOSE Removal

35. DISCONNECT FUEL TUBE SUB-ASSEMBLY Removal

36. REMOVE FRONT LOWER SUSPENSION MEMBER PROTECTOR (for 2WD) Removal

37. DISCONNECT STEERING SLIDING WITH SHAFT YOKE SUB-ASSEMBLY (for 2WD) Removal

38. REMOVE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY (for 4WD) Removal

39. SEPARATE FRONT SPEED SENSOR LH (for 4WD) Removal

40. SEPARATE FRONT SPEED SENSOR RH (for 4WD) Removal

41. REMOVE FRONT AXLE SHAFT LH NUT (for 4WD) Removal

42. REMOVE FRONT AXLE SHAFT RH NUT (for 4WD) Removal

43. REMOVE TIE ROD ASSEMBLY LH (for 4WD) Removal

44. REMOVE TIE ROD ASSEMBLY RH (for 4WD) Removal

45. DISCONNECT HEIGHT CONTROL SENSOR LINK (for 2WD) Removal

46. DISCONNECT HEIGHT CONTROL SENSOR LINK (for 4WD) Removal

47. REMOVE FRONT SHOCK ABSORBER ASSEMBLY LH (for 2WD) Removal

48. REMOVE FRONT SHOCK ABSORBER ASSEMBLY RH (for 2WD) Removal

49. REMOVE FRONT SHOCK ABSORBER ASSEMBLY LH (for 4WD) Removal

50. REMOVE FRONT SHOCK ABSORBER ASSEMBLY RH (for 4WD) Removal

51. REMOVE FRONT LOWER BALL JOINT ASSEMBLY LH (for 2WD) Removal

52. REMOVE FRONT LOWER BALL JOINT ASSEMBLY RH (for 2WD) Removal

53. REMOVE FRONT LOWER BALL JOINT ASSEMBLY LH (for 4WD) Removal

54. REMOVE FRONT LOWER BALL JOINT ASSEMBLY RH (for 4WD) Removal

55. REMOVE FRONT AXLE ASSEMBLY LH (for 4WD) Removal

56. REMOVE FRONT AXLE ASSEMBLY RH (for 4WD) Removal

57. DISCONNECT POWER STEERING LINK WIRE HARNESS (for 2WD) Removal

58. DISCONNECT POWER STEERING LINK WIRE HARNESS (for 4WD) Removal

59. DISCONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY (for 2WD)

60. DISCONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY (for 4WD) Removal

61. REMOVE ENGINE AND TRANSMISSION ASSEMBLY (for 2WD) Removal

62. REMOVE ENGINE AND TRANSMISSION ASSEMBLY (for 4WD) Removal

63. INSTALL ENGINE HANGERS Removal

64. REMOVE FRONT PROPELLER SHAFT ASSEMBLY (for 4WD) Removal

65. REMOVE STARTER ASSEMBLY Removal

66. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

A760E:

A760H: Removal

67. REMOVE OIL DIPSTICK GUIDE SUB-ASSEMBLY (for 2WD) Removal

68. REMOVE OIL DIPSTICK GUIDE SUB-ASSEMBLY (for 4WD) Removal

69. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH Removal

70. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH Removal

71. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH (for 4WD) Removal

72. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH (for 4WD) Removal

73. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY Removal

74. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY (for 2WD) Removal

75. REMOVE FRONT FRAME ASSEMBLY (for 4WD) Removal

76. FIX ENGINE ON ENGINE STAND Removal

77. REMOVE V-RIBBED BELT Removal

78. REMOVE NO. 2 ENGINE COVER Removal

79. REMOVE NO. 1 ENGINE COVER Removal

80. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY Removal

81. REMOVE GENERATOR ASSEMBLY Removal

82. REMOVE COMPRESSOR AND MAGNETIC CLUTCH (for 2WD) Removal

83. REMOVE OIL FILTER BRACKET (for 4WD) Removal

84. REMOVE COMPRESSOR AND MAGNETIC CLUTCH (for 4WD) Removal

85. REMOVE ENGINE MOUNTING BRACKET LH Removal

86. REMOVE ENGINE MOUNTING BRACKET RH Removal

87. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY Removal

88. REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) Removal

89. REMOVE WATER PUMP PULLEY Removal

90. REMOVE ENGINE WIRE Removal

91. REMOVE INJECTOR DRIVER Removal

92. REMOVE INTAKE AIR SURGE TANK ASSEMBLY

Removal

93. REMOVE NO. 2 SURGE TANK STAY Removal

94. DISCONNECT WATER HOSE JOINT Removal

95. REMOVE CRANKSHAFT PULLEY Removal

96. REMOVE WATER INLET Removal

97. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY Disassembly

98. REMOVE OIL STRAINER SUB-ASSEMBLY (for 4WD) Disassembly

99. REMOVE OIL PAN SUB-ASSEMBLY Disassembly

100. REMOVE OIL STRAINER SUB-ASSEMBLY Disassembly

101. REMOVE FUEL PRESSURE PULSATION DAMPER Removal

102. REMOVE NO. 1 FUEL PIPE Removal

103. DISCONNECT NO. 2 FUEL PIPE Removal

104. REMOVE FUEL PUMP ASSEMBLY Removal

105. REMOVE NO. 2 FUEL PIPE Removal

106. REMOVE IGNITION COIL ASSEMBLY Removal

107. REMOVE NO. 1 OIL PIPE Disassembly

108. REMOVE NO. 2 OIL PIPE Disassembly

109. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH Disassembly

110. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH Disassembly

111. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

(a) Remove the bolt and wiring harness clamp bracket.





(b) Remove the 25 bolts and 2 nuts as shown in the illustration.





(c) Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.





NOTICE:
Be careful not to damage the contact surfaces of the cylinder head, cylinder block and chain cover.

HINT
Tape the screwdriver tip before use.

(d) Remove the gasket.





112. REMOVE TIMING CHAIN CASE OIL SEAL

(a) Using a screwdriver, pry out the oil seal.





HINT
Tape the screwdriver tip before use.