Only Passenger Door Lock / Unlock Functions Do Not Operate
DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM: Only Passenger Door LOCK / UNLOCK Functions do not Operate
- Only Passenger Door LOCK / UNLOCK Functions do not Operate
DESCRIPTION
The front door ECU RH receives lock/unlock switch signals and activates the door lock motor according to these signals.
WIRING DIAGRAM
INSPECTION PROCEDURE
PROCEDURE
1. PERFORM ACTIVE TEST USING TECHSTREAM (FRONT DOOR LOCK RH)
(a) Select the Active Test, use the Techstream to generate a control command, and then check the door lock motor function.
Passenger Door (Front door ECU RH)
Result
NG -- INSPECT FUSE (P DOOR 1, P DOOR 2)
OK -- Continue to next step.
2. READ VALUE USING TECHSTREAM (DOOR LOCK POSITION SWITCH)
(a) Use the Data List to check if the door lock position switch is functioning properly.
Passenger Door (Front door ECU RH)
OK:
On tester screen, item changes between ON and OFF according to above chart.
NG -- INSPECT FRONT DOOR LOCK ASSEMBLY RH (DOOR LOCK POSITION SWITCH)
OK -- Continue to next step.
3. CHECK FRONT DOOR ECU RH (OPERATION)
(a) Replace the front door ECU RH with a normal one Overhaul.
(b) Check that all doors can be locked and unlocked by using the master switch.
OK:
All doors can be locked and unlocked with master switch.
NG -- REPLACE MAIN BODY ECU
OK -- END (FRONT DOOR ECU RH IS DEFECTIVE)
4. INSPECT FUSE (P DOOR 1, P DOOR 2)
(a) Remove the P DOOR 1 and P DOOR 2 fuses from the passenger side junction block.
(b) Measure the resistance of the fuse.
Standard resistance:
NG -- REPLACE FUSE
OK -- Continue to next step.
5. CHECK HARNESS AND CONNECTOR (FRONT DOOR ECU RH - BATTERY)
(a) Disconnect the N1 ECU connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard voltage:
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.
6. INSPECT FRONT DOOR LOCK ASSEMBLY RH
(a) w/o Door Closer:
(1) Apply battery voltage to the door lock motor and check operation of the door lock motor.
OK:
(b) w/ Door Closer:
(1) Apply battery voltage to the door lock motor and check operation of the door lock motor.
OK:
NG -- REPLACE FRONT DOOR LOCK ASSEMBLY RH Overhaul
OK -- Continue to next step.
7. CHECK HARNESS AND CONNECTOR (FRONT DOOR ECU RH - FRONT DOOR LOCK RH)
(a) Disconnect the N2 ECU connector.
(b) Disconnect the N8 door lock connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- REPLACE FRONT DOOR ECU RH Overhaul
8. INSPECT FRONT DOOR LOCK ASSEMBLY RH (DOOR LOCK POSITION SWITCH)
(a) w/o Door Closer:
(1) Measure the resistance according to the value(s) in the table below.
Standard resistance:
(b) w/ Door closer:
(1) Measure the resistance according to the value(s) in the table below.
Standard resistance:
NG -- REPLACE FRONT DOOR LOCK ASSEMBLY RH Overhaul
OK -- Continue to next step.
9. CHECK HARNESS AND CONNECTOR (FRONT DOOR ECU RH - FRONT DOOR LOCK RH)
(a) Disconnect the N2 ECU connector.
(b) Disconnect the N8 door lock connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- REPLACE FRONT DOOR ECU RH Overhaul