Installation
SUSPENSION: REAR STABILIZER BAR: INSTALLATION
HINT
A bolt without a torque specification is shown in the standard bolt chart Standard Bolt - Specified Torque For Standard Bolts.
1. INSTALL STABILIZER BAR REAR
(a) Make sure the bracket's arrows face the front of the vehicle.
First temporarily install bolt 1. Then install bolts 2, 3 and 4. Then tighten bolt 5.
Torque : 48 Nm (489 kgf-cm, 35 ft-lbf)
2. INSTALL REAR STABILIZER LINK ASSEMBLY LH
(a) Install the stabilizer link with the 2 nuts and bolt.
Torque : 89 Nm (908 kgf-cm, 66 ft-lbf) for stabilizer bar side
Torque : 26 Nm (265 kgf-cm, 19 ft-lbf) for No. 2 suspension arm side
3. INSTALL REAR STABILIZER LINK ASSEMBLY RH
HINT
Use the same procedures described for the LH side.
4. INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY
(a) Slowly raise the suspension member jack, and install the suspension member to the body.
(b) for Sports package
(1) Install the 2 member stoppers with the 4 bolts labeled B, and install the 4 bolts labeled A.
Torque : 19 Nm (194 kgf-cm, 14 ft-lbf) for bolt labeled A
Torque : 127 Nm (1295 kgf-cm, 94 ft-lbf) for bolt labeled B
(c) for Standard
(1) Install the 4 bolts labeled B.
Torque : 127 Nm (1295 kgf-cm, 94 ft-lbf)
5. CONNECT PNEUMATIC CYLINDER WITH REAR SHOCK ABSORBER ASSEMBLY LH (w/ Air Suspension) Installation
6. CONNECT PNEUMATIC CYLINDER WITH REAR SHOCK ABSORBER ASSEMBLY RH (w/ Air Suspension)
HINT
Use the same procedures described for the LH side.
7. CONNECT REAR SHOCK ABSORBER ASSEMBLY LH (w/o Air Suspension) Installation
8. CONNECT REAR SHOCK ABSORBER ASSEMBLY RH (w/o Air Suspension)
HINT
Use the same procedures described for the LH side.
9. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY LH Installation
10. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY RH
HINT
Use the same procedures described for the LH side.
11. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY Installation
12. INSPECT AND ADJUST NO. 2 AND NO. 3 JOINT ANGLE Installation
13. INSTALL PROPELLER SHAFT HEAT INSULATOR Installation
14. INSTALL FRONT FLOOR NO. 1 HEAT INSULATOR Installation
15. INSTALL TAILPIPE RH Installation
16. INSTALL TAILPIPE LH Installation
17. INSTALL FRONT EXHAUST PIPE ASSEMBLY Installation
18. INSTALL FRONT FLOOR BRACE CENTER Installation
19. INSTALL HEATED OXYGEN SENSOR (for Sensor 2) Installation
20. INSPECT FOR GAS LEAK
21. INSTALL PARKING BRAKE CABLE
(a) Install the cable with the 2 nuts to the vehicle side.
Torque : 8.0 Nm (82 kgf-cm, 71 in-lbf)
22. CONNECT NO. 1 ACTUATOR HARNESS CLAMP
(a) Connect the 2 clamps and connector.
23. INSTALL REAR SPEED SENSOR LH Installation
24. INSTALL REAR SPEED SENSOR RH
HINT
Use the same procedures described for the LH side.
25. INSTALL REAR WHEEL HOUSE LINER LH
(a) Install the liner with the 3 screws, 11 nuts, 2clips to the vehicle side.
26. INSTALL REAR WHEEL HOUSE LINER RH
HINT
Use the same procedures described for the LH side.
27. INSTALL REAR FLOOR SIDE MEMBER COVER RH Installation
28. INSTALL REAR FLOOR SIDE MEMBER COVER LH Installation
29. INSTALL NO. 5 ROCKER PANEL MOULDING PROTECTOR Installation
30. INSTALL NO. 6 ROCKER PANEL MOULDING PROTECTOR Installation
31. INSTALL NO. 1 DIFFERENTIAL SUPPORT PROTECTOR Installation
32. INSTALL NO. 2 DIFFERENTIAL SUPPORT PROTECTOR Installation
33. INSTALL FLOOR NO. 1 UNDER COVER Installation
34. INSTALL LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY LH Installation
35. INSTALL REAR FLOOR FINISH PLATE Installation
36. INSTALL DECK TRIM SIDE BOARD LH Installation
37. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY Installation
38. INSTALL REAR WHEEL
Torque : 140 Nm (1428 kgf-cm, 104 ft-lbf)
39. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
40. INSTALL COWL TOP VENTILATOR LOUVER RH Installation
41. PERFORM INITIALIZATION
(a) Perform initialization Repair Instruction - Initialization.
NOTICE:
Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.
42. CHECK SUSPENSION CONTROL SYSTEM (w/ Air Suspension)
(a) Check the suspension control system Operation Check.
43. INSPECT AND ADJUST REAR WHEEL ALIGNMENT
(a) Inspect and adjust the rear wheel alignment Rear Wheel Alignment.
44. CHECK SPEED SENSOR SIGNAL
(a) Check the speed sensor signal Test Mode Procedure.
45. ADJUST HEADLIGHT ASSEMBLY
(a) Adjust the headlight Adjustments.