Dynamic Radar Cruise Control System
CRUISE CONTROL: DYNAMIC RADAR CRUISE CONTROL SYSTEM: C1A40: ENG / EHV Device
C1A40 - ENG / EHV Device
DESCRIPTION
When the driving support ECU assembly receives a hybrid control system or SFI system malfunction signal from the power management control ECU or ECM via the CAN communication line, DTC C1A40 is stored.
WIRING DIAGRAM
INSPECTION PROCEDURE
PROCEDURE
1. READ OUTPUT DTC (HYBRID CONTROL SYSTEM)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
(e) Read the DTCs.
Result:
B -- GO TO HYBRID CONTROL SYSTEM How to Proceed With Troubleshooting
A -- Continue to next step.
2. READ OUTPUT DTC (SFI SYSTEM)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
(e) Read the DTCs.
Result:
B -- GO TO SFI SYSTEM How to Proceed With Troubleshooting
A -- Continue to next step.
3. CHECK WHETHER DTC OUTPUT RECURS (DTC C1A40)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Clear the DTCs Dynamic Radar Cruise Control System.
(d) Perform the following to make sure that the DTC detection conditions are met.
HINT
If the detection conditions are not met, the malfunction cannot be detected.
(1) Drive the vehicle at a speed of 50 km/h (30 mph) and 170 km/h (105 mph).
(2) Turn the cruise control switch (ON-OFF button) on.
(3) Push the -/SET switch to activate the cruise control.
(e) Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.
(f) Read the DTCs.
Result:
B -- REPLACE POWER MANAGEMENT CONTROL ECU
A -- USE SIMULATION METHOD TO CHECK How To Proceed With Troubleshooting
4. REPLACE POWER MANAGEMENT CONTROL ECU
(a) Replace the power management control ECU Removal.
NEXT -- Continue to next step.
5. CHECK WHETHER DTC OUTPUT RECURS (DTC C1A40)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Clear the DTCs Dynamic Radar Cruise Control System.
(d) Perform the following to make sure that the DTC detection conditions are met.
HINT
If the detection conditions are not met, the malfunction cannot be detected.
(1) Drive the vehicle at a speed of 50 km/h (30 mph) and 170 km/h (105 mph).
(2) Turn the cruise control switch (ON-OFF button) on.
(3) Push the -/SET switch to activate the cruise control.
(e) Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.
(f) Read the DTCs.
Result:
B -- REPLACE ECM
A -- END
6. REPLACE ECM
(a) Replace the ECM Removal.
NEXT -- Continue to next step.
7. CHECK WHETHER DTC OUTPUT RECURS (DTC C1A40)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Clear the DTCs Dynamic Radar Cruise Control System.
(d) Perform the following to make sure that the DTC detection conditions are met.
HINT
If the detection conditions are not met, the malfunction cannot be detected.
(1) Drive the vehicle at a speed of 50 km/h (30 mph) and 170 km/h (105 mph).
(2) Turn the cruise control switch (ON-OFF button) on.
(3) Push the -/SET switch to activate the cruise control.
(e) Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.
(f) Read the DTCs.
Result:
B -- REPLACE DRIVING SUPPORT ECU ASSEMBLY Removal
A -- END