P014D
2ZR-FXE ENGINE CONTROL: SFI SYSTEM: P014C, P014D, P015A, P015B: A/F Sensor Slow Response - Rich to Lean Bank 1 Sensor 1
DESCRIPTION
HINT
Refer to DTC P2195 P2195.
*: Calculated by ECM based on the air fuel ratio sensor output.
MONITOR DESCRIPTION
After the engine has been warmed up, the ECM carries out air-fuel ratio feedback control, and maintains the air-fuel ratio at the theoretical level. In addition, after all the preconditions have been met, active air-fuel ratio control is carried out for approximately 10 seconds and during active air-fuel ratio control, the ECM measures the response of the air-fuel ratio sensor by increasing or decreasing a specific injection quantity based on the theoretical air-fuel ratio learned during normal air-fuel control. The ECM determines whether there is an air-fuel ratio sensor malfunction at the mid-point of active air-fuel ratio control.
If the air-fuel ratio sensor's response ability is reduced, DTC P014C and P014D are output.
If the air-fuel ratio sensor output timing is delayed, DTC P015A and P015B are output.
MONITOR STRATEGY
TYPICAL ENABLING CONDITIONS
TYPICAL MALFUNCTION THRESHOLDS
P014C: Air Fuel Ratio Sensor (Sensor 1) Response Rate (Rich to Lean Response Rate)
P014D: Air Fuel Ratio Sensor (Sensor 1) Response Rate (Lean to Rich Response Rate)
P015A: Air Fuel Ratio Sensor (Sensor 1) Response Rate (Rich to Lean Delay)
P015B: Air Fuel Ratio Sensor (Sensor 1) Response Rate (Lean to Rich Delay)
MONITOR RESULT
Refer to detailed information in Checking Monitor Status Mode 6 Data.
P014C: O2 Sensor / RL RES RATE B1S1
P014D: O2 Sensor / LR RES RATE B1S1
P015A: O2 Sensor / RL DELAY B1S1
P015B: O2 Sensor / LR DELAY B1S1
CONFIRMATION DRIVING PATTERN
HINT
Performing this confirmation pattern will activate the air fuel ratio sensor response monitor.
1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure) Reading and Clearing Diagnostic Trouble Codes.
5. Turn the power switch off and wait for at least 30 seconds.
6. Turn the power switch on (IG) and turn the Techstream on.
7. Put the engine in inspection mode (maintenance mode) Component Tests and General Diagnostics.
8. Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor.
9. Check that O2 Sensor / Current is incomplete.
HINT
The test values for the test items RL RES RATE B1S1, LR RES RATE B1S1, RL DELAY B1S1 and LR DELAY B1S1 do not exist in the Detail of O2 Sensor monitor at this time (the initial value of "0.000" is indicated in each test item).
10. Start the engine and warm it up (until the engine coolant temperature is 75°C (167°F) or higher) [A].
11. Drive the vehicle at a constant speed between 75 and 100 km/h (47 and 62 mph) for 10 minutes [B].
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
12. Check that the monitor item O2 Sensor / Current becomes Complete.
HINT
Check the test values on the Techstream by entering the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / Details / RL RES RATE B1S1, LR RES RATE B1S1, RL DELAY B1S1 and LR DELAY B1S1.
13. If the monitor item O2 Sensor / Current does not become Complete (if the test values indicated on the Techstream do not change), perform Readiness Monitor Drive Pattern for the air fuel ratio sensor and heated oxygen sensor Monitors, Trips, Drive Cycles and Readiness Codes.
14. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
15. Read the pending DTCs.
HINT
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
16. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
17. Input the DTC: P014C, P014D, P015A or P015B.
18. Check the DTC judgment result.
HINT
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
19. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs Reading and Clearing Diagnostic Trouble Codes.
HINT
- If a permanent DTC is output, the system is malfunctioning.
- If no permanent DTC is output, the system is normal.
WIRING DIAGRAM
Refer to DTC P2195 P2195.
INSPECTION PROCEDURE
HINT
- A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
- A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.
- Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
- Sensor 1 refers to the sensor closest to the engine assembly.
- Sensor 2 refers to the sensor farthest away from the engine assembly.
PROCEDURE
1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P014C, P014D, P015A OR P015B)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
(e) Read the DTCs.
Result
HINT
If any DTCs other than P014C, P014D, P015A or P015B are output, troubleshoot those DTCs first.
B -- GO TO DTC CHART SFI System
A -- Continue to next step.
2. INSPECT AIR FUEL RATIO SENSOR NO.2 (HEATER RESISTANCE)
(a) Inspect the air fuel ratio sensor Air Fuel Ratio Sensor.
NG -- REPLACE AIR FUEL RATIO SENSOR NO.2 Removal
OK -- Continue to next step.
3. CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) P2237
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.
4. CHECK AIR FUEL RATIO SENSOR NO.2
(a) Check that the proper air fuel ratio sensors are installed to the vehicle.
NG -- REPLACE AIR FUEL RATIO SENSOR NO.2 Removal
OK -- Continue to next step.
5. PERFORM CONFIRMATION DRIVING PATTERN
(a) Drive the vehicle according to the Confirmation Driving Pattern.
NEXT -- Continue to next step.
6. CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P015A OR P015B)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
(e) Read the pending DTCs.
Result
B -- CHECK FOR INTERMITTENT PROBLEMS Check For Intermittent Problems
A -- Continue to next step.
7. REPLACE AIR FUEL RATIO SENSOR NO.2
(a) Replace the air fuel ratio sensor Removal.
NEXT -- Continue to next step.
8. PERFORM CONFIRMATION DRIVING PATTERN
(a) Drive the vehicle according to the Confirmation Driving Pattern.
NEXT -- Continue to next step.
9. CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P015A OR P015B)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
(e) Read the pending DTCs.
Result
B -- CHECK ENGINE TO DETERMINE CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO P0171
A -- END