Installation
AXLE: FRONT AXLE HUB: INSTALLATION
1. INSTALL FRONT AXLE HUB BEARING
(a) Using SST and a press, install a new front axle hub bearing to the steering knuckle.
SST : 09950-60020
09951-00810
SST : 09950-70010
09951-07100
2. INSTALL FRONT LOWER BALL JOINT ASSEMBLY Installation
3. INSTALL FRONT DISC BRAKE DUST COVER
(a) Install the disc brake dust cover to the steering knuckle with the 4 bolts.
Torque : 8.3 Nm (85 kgf-cm, 73 in-lbf)
4. INSTALL FRONT AXLE HUB SUB-ASSEMBLY
(a) Using SST and a press, install the front axle hub sub-assembly.
SST : 09608-32010
SST : 09950-60020
09951-00810
SST : 09950-70010
09951-07100
5. INSTALL FRONT AXLE HUB HOLE SNAP RING
(a) Using snap ring pliers, install a new front axle hub hole snap ring.
6. INSTALL NO. 1 FRONT WHEEL BEARING DUST DEFLECTOR
(a) Using SST and a hammer, install a new No. 1 front wheel bearing dust deflector.
SST : 09316-60011
09316-00011
09316-00031
SST : 09608-32010
HINT
Align the hole for the speed sensor in the No. 1 front wheel bearing dust deflector with the steering knuckle.
7. INSTALL FRONT AXLE ASSEMBLY
(a) Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly.
(b) Install the steering knuckle with the front axle assembly to the front shock absorber with the 2 bolts and 2 nuts.
Torque : 210 Nm (2140 kgf-cm, 155 ft-lbf)
NOTICE:
* If the bolts and nuts are reused, apply a small amount of engine oil to the threads of the nuts.
* Be careful not to damage the drive shaft boot or speed sensor rotor.
8. INSTALL FRONT SUSPENSION LOWER NO. 1 ARM Installation
9. INSTALL TIE ROD END SUB-ASSEMBLY Installation
10. INSTALL FRONT DISC Reassembly
11. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY
(a) Install the front disc brake caliper assembly to the steering knuckle with the 2 bolts.
Torque : 107 Nm (1090 kgf-cm, 79 ft-lbf)
NOTICE:
Do not twist the brake hose when installing the front disc brake caliper assembly.
12. INSTALL FRONT AXLE HUB NUT
(a) Clean the threaded parts on the drive shaft and axle hub nut using a non-residue solvent.
NOTICE:
* Be sure to perform this work for a new drive shaft.
* Keep the threaded parts free of oil and foreign objects.
(b) Using a socket wrench (30 mm), install a new axle hub nut.
Torque : 294 Nm (3000 kgf-cm, 217 ft-lbf)
HINT
Stake the nut after inspecting for looseness and runout in the following steps.
13. SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY
(a) Remove the 2 bolts and separate the front disc brake caliper assembly from the steering knuckle.
NOTICE:
Use wire or an equivalent tool to keep the brake caliper from hanging by its flexible hose.
14. REMOVE FRONT DISC Disassembly
15. INSPECT FRONT AXLE HUB BEARING LOOSENESS Front Axle Hub
16. INSPECT FRONT AXLE HUB RUNOUT Front Axle Hub
17. INSTALL FRONT DISC Reassembly
18. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY
(a) Install the front disc brake caliper assembly to the steering knuckle with the 2 bolts.
Torque : 107 Nm (1,090 kgf-cm, 79 ft-lbf)
NOTICE:
Do not twist the brake hose when installing the front disc brake caliper assembly.
19. INSTALL FRONT SPEED SENSOR Installation
20. INSTALL FRONT AXLE HUB NUT
(a) Using a chisel and hammer, stake the axle hub nut.
21. INSTALL FRONT WHEEL
Torque : 103 Nm (1,050 kgf-cm, 76 ft-lbf)
22. ADJUST FRONT WHEEL ALIGNMENT
HINT
Front Wheel Alignment
23. CHECK ABS SPEED SENSOR SIGNAL
HINT
Test Mode Procedure