C2303
P311 HYBRID TRANSMISSION / TRANSAXLE: ELECTRONIC SHIFT LEVER SYSTEM: C2303: Short in Power Source Relay Circuit
C2303 - Short in Power Source Relay Circuit
DESCRIPTION
The P CON MTR relay is activated by output voltage from the transmission control ECU and supplies power to the shift control actuator (parking lock motor). The transmission control ECU outputs this DTC when it detects a malfunction in the P CON MTR relay.
WIRING DIAGRAM
Refer to the wiring diagram for DTC C2301 C2301.
INSPECTION PROCEDURE
NOTICE:
It is not possible to clear the following DTCs using the Techstream: DTCs C2300 (Actuator System Malfunction), C2301 (Shift Changing Time Malfunction), C2303 (Short in Power Source Relay Circuit), C2304 (Open or Short Circuit in U Phase), C2305 (Open or Short Circuit in V Phase), C2306 (Open or Short Circuit in W Phase), C2307 (Power Supply) and C2309 (Open in B+ Circuit). After the repair, it is necessary to disconnect the P CON MAIN fuse and wait for at least 60 seconds to clear the DTCs.
PROCEDURE
1. CHECK SHIFT CONTROL ACTUATOR ASSEMBLY (SHIFT CONTROL ACTUATOR ASSEMBLY POWER SOURCE CIRCUIT)
(a) Disconnect connector from the shift control actuator assembly connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Text in Illustration
(c) Connect the shift control actuator assembly connector.
(d) Turn the power switch off.
NG -- CHECK RELAY (P CON MTR)
OK -- Continue to next step.
2. CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU ASSEMBLY - SHIFT CONTROL ACTUATOR)
(a) Disconnect connector A35 from the transmission control ECU assembly.
(b) Disconnect connector from the shift control actuator assembly.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance (Check for Short):
Text in Illustration
(d) Connect the shift control actuator assembly connector.
(e) Connect the transmission control ECU assembly connector.
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- REPLACE TRANSMISSION CONTROL ECU ASSEMBLY Components
3. CHECK RELAY (P CON MTR)
(a) Remove the P CON MTR relay from the engine room junction block assembly.
Text in Illustration
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
(c) Install the P CON MTR relay to the engine room junction block assembly.
NG -- REPLACE RELAY (P CON MTR)
OK -- Continue to next step.
4. CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU ASSEMBLY - P CON MTR RELAY)
(a) Disconnect connector A35 from the transmission control ECU assembly.
(b) Remove the P CON MTR relay from the engine room junction block assembly.
Text in Illustration
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance (Check for Short):
Text in Illustration
(d) Install the P CON MTR relay to the engine room junction block assembly.
(e) Connect the transmission control ECU assembly connector.
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.
5. CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ACTUATOR ASSEMBLY - P CON MTR RELAY)
(a) Disconnect connector from the shift control actuator assembly.
(b) Remove the P CON MTR relay from the engine room junction block assembly.
Text in Illustration
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance (Check for Short):
Text in Illustration
(d) Install the P CON MTR relay to the engine room junction block assembly.
(e) Connect the shift control actuator assembly connector.
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- CHECK FOR INTERMITTENT PROBLEMS How To Proceed With Troubleshooting