P0ADC
HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM: P0ADB-227, P0ADC-226: Hybrid Battery Positive Contactor Control Circuit Low
P0ADC-226 - Hybrid Battery Positive Contactor Control Circuit High
DESCRIPTION
Refer to the description for DTC P0AE6-225 P0AE6.
WIRING DIAGRAM
Refer to the wiring diagram for DTC P0AE6-225 P0AE6.
INSPECTION PROCEDURE
CAUTION:
- Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
- After disconnecting the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
HINT
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
PROCEDURE
1. CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HYBRID BATTERY JUNCTION BLOCK)
(a) Disconnect connector A58 from the hybrid vehicle control ECU.
(b) Turn the power switch on (IG).
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Text in Illustration
NOTICE:
Turning the power switch on (IG) with the hybrid vehicle control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.
(d) Turn the power switch off.
(e) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
(f) Connect the hybrid vehicle control ECU connector.
NG -- CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HYBRID BATTERY JUNCTION BLOCK)
OK -- Continue to next step.
2. CHECK FOR INTERMITTENT PROBLEMS
(a) Check for intermittent problems Check for Intermittent Problems.
Result:
B -- REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
A -- REPLACE HYBRID VEHICLE CONTROL ECU Components
3. CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - HYBRID BATTERY JUNCTION BLOCK)
CAUTION:
Be sure to wear insulated gloves.
(a) Check that the service plug grip is not installed.
NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
(b) Disconnect connector z16 from the hybrid battery junction block assembly.
(c) Disconnect connector A58 from the hybrid vehicle control ECU.
(d) Turn the power switch on (IG).
NOTICE:
Turning the power switch on (IG) with the hybrid vehicle control ECU and hybrid battery junction block assembly connectors disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.
(e) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Text in Illustration
(f) Turn the power switch off.
(g) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
(h) Connect the hybrid vehicle control ECU connector.
(i) Connect the hybrid battery junction block assembly connector.
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.
4. CHECK HARNESS AND CONNECTOR (HYBRID BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND)
CAUTION:
Be sure to wear insulated gloves.
(a) Check that the service plug grip is not installed.
NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
(b) Disconnect connector z16 from the hybrid battery junction block assembly.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
(d) Connect the hybrid battery junction block assembly connector.
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- REPLACE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY Components