Operation Check

DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM: OPERATION CHECK

1. CHECK POWER DOOR LOCK OPERATION

NOTICE:
The operation check below is based on the non-customized initial condition of the vehicle.

(a) Check basic functions.

(1) Check that all doors lock when the lock side of the door control switch (for manual operation) is pressed, and all doors unlock when the unlock side is pressed.

(2) Check that all doors lock when the driver door lock key cylinder is turned to lock using the key.

(3) Check that driver door unlock when the driver door lock key cylinder is turned to unlock using the key.

(b) Check the key lock-in prevention function.

NOTICE:
In order to prevent the key from being locked in, the following inspection should be performed with the driver door window open.

(1) Turn the engine switch on (IG) or (ACC).

(2) With the driver door open, check that all doors unlock immediately after the door lock knob for the driver door is locked.

(3) With the driver door open, check that all doors unlock immediately after the lock side of the door control switch (for manual operation) is pressed.

(4) With the driver door open, lock the driver door lock knob and hold it for 2 seconds or more, then close the driver door and check that all doors unlock.

(c) Check the security function of the door lock control system.

(1) Close all doors and leave the driver door window open so that the door control switch can be operated from outside the vehicle. (Step 1)

(2) Open the driver door and remove the key from the vehicle. With the door still open, lock the door using the lock knob and close the door. Then, check that the doors do not unlock when the unlock side of the door control switch (for manual operation) is pressed from outside the vehicle.

(3) Starting from Step 1, with the key outside the vehicle, close and lock the driver door using the mechanical key. Then, check that the doors do not unlock when the unlock side of the door control switch (for manual operation) is pressed from outside the vehicle.

(4) Starting from Step 1, with the key outside the vehicle, close and lock the driver door using wireless door lock or entry lock operation. Then, check that the doors do not unlock when the unlock side of the door control switch (for manual operation) is pressed from outside the vehicle.

HINT
Check that the security function of the door lock control system is canceled under the following conditions:

* The engine switch is turned on (IG).

* The driver door is unlocked using the key.

* The unlock side of the door control switch (for manual operation) is pressed after the door lock knob is unlocked manually.

* The doors are unlocked by wireless operation.

(d) Check the illumination function.

(1) Set the map light switch to the door position.

(2) When the driver door is unlocked by the key linked or wireless operation with the engine switch off and all doors closed and locked, check that the roof light comes on.

(3) Check that the interior light turns off in approximately 15 seconds* if the doors have not been opened.

HINT
*: This function can be customized Programming and Relearning.

(e) Check the key-linked 2-step unlock function.

(1) Lock all doors.

(2) Check that only the driver door unlocks when the driver door lock cylinder is turned to unlock once using the key and other doors unlock when turned to unlock consecutively once again.

(f) Check the driver door-linked automatic door unlock function.

HINT
The default setting for A/T is OFF. If necessary, the function must be set to ON through the customize function.

(1) When the driver door is closed, turning the engine switch from on (IG) to off and opening the driver door within approximately 45 seconds will automatically unlock all doors.

(g) Check the shift linked automatic door lock function (for A/T).

HINT
* The default setting for models without the occupant classification system is OFF. If necessary, the function must be set to ON through the customize function.
* The automatic locking operation is disabled if the crash detection sensor (built into the center airbag sensor) unlocking system malfunctions when the engine switch is on (IG) and all doors are closed.

(1) When the engine switch is on (IG) and the shift lever is moved from P to any position other than P, check that all doors lock automatically.

(h) Check the shift linked automatic door unlock function (for A/T).

(1) When the engine switch is on (IG) and the shift lever is moved to P from any position other than P, check that all doors unlock automatically.

(i) Check the speed-sensitive automatic door lock function.

HINT
* The default setting for models with the occupant classification system and A/T is OFF. If necessary, the function must be set to ON through the customize function.
* The automatic locking operation is disabled if the crash detection sensor (built into the center airbag sensor) unlocking system has a malfunction when the engine switch is on (IG) and all doors are closed.

(1) When any door is unlocked and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that all doors lock automatically.