Operation CHARM: Car repair manuals for everyone.

Installation





EXTERIOR: REAR BUMPER: INSTALLATION

HINT
A bolt without a torque specification is shown in the standard bolt chart Standard Bolt - Specified Torque For Standard Bolts.

1. INSTALL REAR BUMPER LOWER RETAINER LH

(a) Attach the 3 claws to install the rear bumper lower retainer, and then install the 3 screws and grommet.

2. INSTALL REAR BUMPER LOWER RETAINER RH

HINT
Use the same procedure described for the LH side.

3. INSTALL REAR BUMPER LOWER SIDE RETAINER LH

(a) Attach the claw to install the rear bumper lower side retainer and install the screw.

4. INSTALL REAR BUMPER LOWER SIDE RETAINER RH

HINT
Use the same procedure described for the LH side.

5. INSTALL REAR BUMPER SIDE SUPPORT LH

(a) Attach the 5 claws to install the rear bumper side support and install the 4 screws.

6. INSTALL REAR BUMPER SIDE SUPPORT RH

HINT
Use the same procedure described for the LH side.

7. INSTALL REAR BUMPER UPPER RETAINER LH

(a) Attach the 2 clips to install the rear bumper upper retainer.

8. INSTALL REAR BUMPER UPPER RETAINER RH

HINT
Use the same procedure described for the LH side.

9. INSTALL REAR COMBINATION LIGHT ASSEMBLY LH Installation

10. INSTALL REAR COMBINATION LIGHT ASSEMBLY RH

HINT
Use the same procedure described for the LH side.

11. INSTALL LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY LH Installation

12. INSTALL LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY RH Installation

13. INSTALL REAR FLOOR FINISH PLATE Installation

14. INSTALL TOOL BOX (w/o Spare Tire)

15. INSTALL DECK BOARD ASSEMBLY (w/o Spare Tire)

16. INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER Installation

17. INSTALL NO. 1 COOLER COVER (w/ Rear Cooler) Installation

18. INSTALL NO. 2 LUGGAGE COMPARTMENT TRIM HOOK (w/o Rear Cooler) Installation

19. INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY Installation

20. INSTALL DECK TRIM SIDE BOARD LH Installation

21. INSTALL DECK TRIM SIDE BOARD RH

HINT
Use the same procedure described for the LH side.

22. INSTALL ROPE HOOK Installation

23. INSTALL ROPE HOOK ASSEMBLY Installation

24. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY Installation

25. INSTALL LUGGAGE COMPARTMENT DOOR HINGE COVER LH Installation

26. INSTALL LUGGAGE COMPARTMENT DOOR HINGE COVER RH Installation

27. INSTALL REAR BUMPER NO. 1 REINFORCEMENT

(a) Install the rear bumper No. 1 reinforcement with the 8 bolts.

Torque : 20 Nm (204 kgf-cm, 15 ft-lbf)

28. INSTALL REAR BUMPER ARM REINFORCEMENT LH

(a) Attach the 6 claws to install the rear bumper arm reinforcement.

29. INSTALL REAR BUMPER ARM REINFORCEMENT RH

HINT
Use the same procedure described for the LH side.

30. INSTALL REAR BUMPER ENERGY ABSORBER

(a) Install the rear bumper energy absorber.

31. INSTALL REAR BUMPER COVER

(a) w/ Intuitive Parking Assist System:

Connect the No. 3 floor wire connector.

(b) Attach the 18 claws to install the rear bumper cover.

(c) Install the 2 rear bumper seal brackets.

(d) Install the 6 screws and 6 clips.

32. INSTALL REAR BUMPER PLATE LH

(a) Attach the 3 claws to install the rear bumper plate.

33. INSTALL REAR BUMPER PLATE RH

HINT
Use the same procedure described for the LH side.