Cylinder Head Assembly: Testing and Inspection
2UR-FSE ENGINE MECHANICAL: CYLINDER HEAD: INSPECTION
HINT
When viewed from the rear of the engine assembly, Bank 1 is on the left side and Bank 2 is on the right side.
1. INSPECT CYLINDER HEAD SUB-ASSEMBLY
(a) Using a precision straightedge and feeler gauge, measure the warpage of the surfaces where the cylinder head contacts the cylinder block and manifold.
Standard warpage:
Maximum warpage:
0.10 mm (0.00394 in.)
If the warpage is greater than the maximum, replace the cylinder head.
(b) Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks.
If cracked, replace the cylinder head.
2. INSPECT INTAKE VALVE
(a) Using a micrometer, measure the diameter of the valve stem.
Standard valve stem diameter:
5.470 to 5.485 mm (0.215 to 0.216 in.)
If the diameter is not as specified, replace the valve and guide bush.
(b) Using a vernier caliper, measure the valve head margin thickness.
Standard margin thickness:
1.25 mm (0.0492 in.)
Minimum margin thickness:
0.50 mm (0.0197 in.)
If the margin thickness is less than the minimum, replace the intake valve.
(c) Using a vernier caliper, measure the valve's overall length.
Standard overall length:
105.85 mm (4.17 in.)
Minimum overall length:
105.35 mm (4.15 in.)
If the overall length is less than the minimum, replace the intake valve.
3. INSPECT EXHAUST VALVE
(a) Using a micrometer, measure the diameter of the valve stem.
Standard valve stem diameter:
5.465 to 5.480 mm (0.215 to 0.216 in.)
If the diameter is not as specified, replace the valve and guide bush.
(b) Using a vernier caliper, measure the valve head margin thickness.
Standard margin thickness:
1.4 mm (0.0551 in.)
Minimum margin thickness:
0.50 mm (0.0197 in.)
If the margin thickness is less than the minimum, replace the exhaust valve.
(c) Using a vernier caliper, measure the valve's overall length.
Standard overall length:
110.40 mm (4.35 in.)
Minimum overall length:
109.90 mm (4.33 in.)
If the overall length is less than the minimum, replace the exhaust valve.
4. INSPECT INTAKE VALVE SEAT
(a) Apply a light coat of Prussian blue to the valve face.
(b) Lightly press the valve face against the valve seat.
HINT
Do not rotate the valve while pressing the valve.
(c) Check the valve face and valve seat.
(1) Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.1 to 1.5 mm (0.0433 to 0.0591 in.).
If not, correct the valve seat.
(2) Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.
If not, correct the valve seat.
5. INSPECT EXHAUST VALVE SEAT
(a) Apply a light coat of Prussian blue to the valve face.
(b) Lightly press the valve face against the valve seat.
(c) Check the valve face and valve seat.
(1) Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.1 to 1.5 mm (0.0433 to 0.0591 in.).
If not, correct the valve seat.
(2) Check that the contact surface of the valve seat and valve face are even around the entire valve seat.
If not, correct the valve seat.
6. INSPECT INNER COMPRESSION SPRING
(a) Using a vernier caliper, measure the free length of the inner compression spring.
Standard free length:
51.70 mm (2.04 in.)
If the free length is not as specified, replace the spring.
(b) Using a steel square, measure the deviation of the inner compression spring.
Maximum deviation:
1.0 mm (0.0394 in.)
Maximum angle (reference):
2°
If the deviation is greater than the maximum, replace the spring.
7. INSPECT VALVE GUIDE BUSH OIL CLEARANCE
(a) Using a caliper gauge, measure the inside diameter of the guide bush.
Standard bush inside diameter:
5.51 to 5.53 mm (0.217 to 0.218 in.)
(b) Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.
Standard oil clearance:
Maximum oil clearance:
If the clearance is greater than the maximum, replace the valve and guide bush.
8. INSPECT CAMSHAFT THRUST CLEARANCE
(a) Inspect the bank 1 camshafts.
(1) Install the bank 1 camshafts.
(2) Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.
Standard thrust clearance:
0.08 to 0.140 mm (0.00315 to 0.00551 in.)
Maximum thrust clearance:
0.15 mm (0.00591 in.)
If the thrust clearance is greater than the maximum, replace the cylinder head. If the thrust surface is damaged, replace the camshaft.
(b) Inspect the bank 2 camshafts.
(1) Install the bank 2 camshafts.
(2) Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.
Standard thrust clearance:
0.08 to 0.140 mm (0.00315 to 0.00551 in.)
Maximum thrust clearance:
0.15 mm (0.00591 in.)
If the thrust clearance is greater than the maximum, replace the cylinder head. If the thrust surface is damaged, replace the camshaft.