Pinpoint Test P: Voice Recognition Is Inoperative/Does Not Operate Correctly
Information and Entertainment System
Pinpoint Tests
Pinpoint Test P: Voice Recognition Is Inoperative/Does Not Operate Correctly
Refer to Wiring Diagram Set 130, Audio System/Navigation for schematic and connector information. Diagrams By Number
Normal Operation
When the VOICE switch is pressed, it changes the reference voltage on the voice recognition circuit and the audio system enters voice recognition mode. If the vehicle is equipped with navigation, the VOICE switch is wired to the Audio Control Module (ACM). If the vehicle is not equipped with navigation, the VOICE switch is wired to the Accessory Protocol Interface Module (APIM). For all vehicles, a microphone located in the auto-dimming interior mirror receives the voice command and sends a signal to the APIM. The microphone is also used to detect outgoing audio during a phone call.
If the vehicle is equipped with navigation, the APIM receives the microphone input and also broadcasts it to the ACM through a pair of circuits. The first voice commands spoken determine which system handles the voice commands.
- DTC B1038 (Microphone Input Circuit Failure) - set by the APIM (V1) during the on-demand self-test if it does not detect the microphone.
- DTC B1D79:01 (Microphone Input: General Electrical Failure) - set by the navigation ACM or the APIM (V2) during the microphone test when it does not receive an adequate signal from the microphone when the test tone is sounded.
This pinpoint test is intended to diagnose the following:
- Fuse
- Wiring, terminals or connectors
- Steering wheel controls
- Microphone (part of the auto-dimming interior mirror)
- ACM (if equipped with navigation)
- APIM
PINPOINT TEST P: VOICE RECOGNITION IS INOPERATIVE/DOES NOT OPERATE CORRECTLY
NOTICE: Use the correct probe adapter(s) when making measurements. Failure to use the correct probe adapter(s) may damage the connector.
NOTE: Failure to disconnect the battery when instructed will result in false resistance readings. Refer to Battery.
-------------------------------------------------
P1 CHECK THE OPERATION OF THE STEERING WHEEL CONTROLS
- Operate the audio system in radio tuner (AM/FM) mode.
- Press the VOICE button on the steering wheel controls.
- Does the audio system enter voice recognition mode?
Yes
If the vehicle is equipped with navigation, GO to P2.
Otherwise, GO to P5.
No
Go To Pinpoint Test M to diagnose the steering wheel controls system. Pinpoint Test M: The Steering Wheel Controls Are Inoperative/Do Not Operate Correctly
-------------------------------------------------
P2 CHECK THE MICROPHONE SIGNAL TO THE ACM
- Ignition OFF.
- Disconnect: ACM C2253c.
- NOTE: ACM C2253a must remain connected for this step to produce accurate results.
- Operate the audio system in radio tuner (AM/FM) mode.
- Press the VOICE button on the steering wheel controls.
- While speaking a command, measure the AC voltage between the ACM C2253c-11, circuit VMT02 (GN/OG), harness side and the ACM C2253c-12, circuit RMT02 (BN/YE), harness side.
- Is a fluctuating AC voltage present?
Yes
GO to P11.
No
GO to P3.
-------------------------------------------------
P3 CHECK THE MICROPHONE CIRCUITS TO THE ACM FOR A SHORT TO VOLTAGE
- Ignition OFF.
- Disconnect: APIM C3342.
- Ignition ON.
- Measure the voltage between the ACM C2253c-11, circuit VMT02 (GN/OG), harness side and ground; and between the ACM C2253c-12, circuit RMT02 (BN/YE), harness side and ground.
- Is any voltage present?
Yes
REPAIR the circuit in question. TEST the system for normal operation.
No
GO to P4.
-------------------------------------------------
P4 CHECK THE MICROPHONE CIRCUITS TO THE ACM FOR AN OPEN OR SHORT TO GROUND
- Ignition OFF.
- Measure the resistance between the ACM C2253c-11, circuit VMT02 (GN/OG), harness side and the APIM C3342-12, circuit VMT02 (GN/OG), harness side; and between the ACM C2253c-11, circuit VMT02 (GN/OG), harness side and ground.
- Measure the resistance between the ACM C2253c-12, circuit RMT02 (BN/YE), harness side and the APIM C3342-13, circuit RMT02 (BN/YE), harness side; and between the ACM C2253c-12, circuit RMT02 (BN/YE), harness side and ground.
- Is the resistance less than 5 ohms between the ACM and the APIM, and greater than 10,000 ohms between the ACM and ground?
Yes
GO to P5.
No
REPAIR the circuit in question. TEST the system for normal operation.
-------------------------------------------------
P5 CHECK THE MICROPHONE POWER CIRCUIT
- Ignition OFF.
- Disconnect: Auto-Dimming Interior Mirror C911.
- Ignition ON.
- Measure the voltage between the auto-dimming interior mirror C911-1, circuit CBP41 (BU), harness side and ground.
- Is the voltage greater than 10 volts?
Yes
GO to P6.
No
REPAIR the circuit. TEST the system for normal operation.
-------------------------------------------------
P6 CHECK THE MICROPHONE GROUND FOR AN OPEN
- Ignition OFF.
- Disconnect: Negative Battery Cable.
- Measure the resistance between the auto-dimming interior mirror C911-10, circuit GD133 (BK), harness side and ground.
- Is the resistance less than 5 ohms?
Yes
GO to P7.
No
REPAIR the circuit. TEST the system for normal operation.
-------------------------------------------------
P7 CHECK THE MICROPHONE CIRCUITS FOR A SHORT TO VOLTAGE
- Connect: Negative Battery Cable.
- Disconnect: APIM C3342.
- Ignition ON.
- Measure the voltage between the auto-dimming interior mirror C911-4, circuit VMN02 (WH/BN), harness side and ground; and between the auto-dimming interior mirror C911-5, circuit RMN02 (VT/BN), harness side and ground.
- Is any voltage present?
Yes
REPAIR the circuit in question. TEST the system for normal operation.
No
GO to P8.
-------------------------------------------------
P8 CHECK THE MICROPHONE CIRCUITS FOR AN OPEN OR SHORT TO GROUND
- Ignition OFF.
- Measure the resistance between the inside rear view mirror, harness side and the APIM, harness side; and between the auto-dimming interior mirror, harness side and ground as follows:
- Is the resistance less than 5 ohms between the auto-dimming interior mirror and the APIM, and greater than 10,000 ohms between the auto-dimming interior mirror and ground?
Yes
GO to P9.
No
REPAIR the circuit in question. TEST the system for normal operation.
-------------------------------------------------
P9 ISOLATE THE AUTO-DIMMING INTERIOR MIRROR
- Connect: APIM C3342.
- Install a new auto-dimming interior mirror.
- Operate the audio system in radio tuner (AM/FM) mode.
- Press the VOICE button on the steering wheel controls, and attempt several voice commands.
- Does the voice recognition operate correctly?
Yes
The fault was caused by an inoperative auto-dimming interior mirror. The system is now operating correctly.
No
GO to P10.
-------------------------------------------------
P10 CHECK FOR CORRECT APIM OPERATION
- Connect: All Disconnected Connectors.
- Disconnect the APIM connector.
- Check for:
- corrosion
- damaged pins
- pushed-out pins
- Connect the APIM connector and make sure it seats correctly.
- Wait 2 minutes for the APIM to re-initialize.
- Is the concern still present?
Yes
INSTALL a new APIM. REFER to Accessory Protocol Interface Module (APIM) Accessory Protocol Interface Module (APIM). TEST the system for normal operation.
No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
-------------------------------------------------
P11 CHECK FOR CORRECT ACM OPERATION
- Disconnect all the ACM connectors.
- Check for:
- corrosion
- damaged pins
- pushed-out pins
- Connect all the ACM connectors and make sure they seat correctly.
- Operate the system and verify the concern is still present.
- Is the concern still present?
Yes
INSTALL a new ACM. REFER to Audio Control Module (ACM) Audio Control Module (ACM). TEST the system for normal operation.
No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
-------------------------------------------------