Pinpoint Test V: DTCs B103B And B1111
Seats
Pinpoint Tests
Pinpoint Test V: DTCs B103B and B1111
Refer to Wiring Diagram Set 119, Climate Controlled Seats for schematic and connector information. Diagrams By Number
Normal Operation
Climate controlled seats are independently controlled by the Dual Climate Controlled Seat Module (DCSM) mounted to the bottom of the passenger seat cushion. The climate controlled seat system only operates with the engine running, however, if using a scan tool to command the DCSM, diagnostic testing can be carried out with the ignition ON. The system receives voltage from Battery Junction Box (BJB) fuse 22 (30A) supplying voltage into DCSM C3265a pins E and F, circuit CBX01 (GN/RD). If voltage is disconnected from either pin E or F of DCSM C3265a both seats will remain operational because the voltage supply circuits are connected internally in the DCSM. However, if a fault occurs setting a DTC specific to either climate controlled seat, only the affected seat will be disabled.
The seat cushion and backrest are equipped with a Thermo-Electric Device (TED) assembly that includes a seat blower (fan motor, serviced as an assembly with the TED). Cabin air is drawn through the blower and distributed to each of the TED modules. The TEDs then heat or cool the air. The air is then directed into the foam pad and manifold where it is distributed along the surface of the cushion and backrest of the seat. Once the system is activated, the DCSM uses a set of flexible algorithms to control the heating/cooling modes and the blower speed dependant on the HVAC module seat switch settings.
- DTC B103B (Thermo-Electric Driver Overcurrent Low) - If DCSM outputs to the driver seat backrest or cushion TED (circuit pins G, H, J or K at the DCSM connector) or any components within these circuit loops are shorted to ground or a TED resistance of less than 0.9 ohm is sensed, the DCSM will shut down the driver seat system and set this DTC.
- DTC B1111 (Driver Thermo-Electric Device Control Overtemperature Fault) - If the DCSM TED driver integrated circuit temperature exceeds 175°C (347°F), the DCSM will shut down the driver seat system and set this DTC.
This pinpoint test is intended to diagnose the following:
- Wiring, terminals or connectors
- TED assembly
- DCSM
PINPOINT TEST V: DTCs B103B AND B1111
NOTICE: When taking measurements at Dual Climate Controlled Seat Module (DCSM) harness connectors, do not insert the electrical probes into the female connector pins. Inserting the probes into connector pins can cause intermittent or open electrical connections after reassembly resulting in Diagnostic Trouble Codes (DTCs) and system failure. Touching the tip of these connector pins is recommended instead.
NOTE: The air bag warning indicator illuminates when the correct Restraints Control Module (RCM) fuse is removed and the ignition is ON.
NOTE: The Supplemental Restraint System (SRS) must be fully operational and free of faults before releasing the vehicle to the customer.
-------------------------------------------------
V1 CHECK TED CIRCUITS FOR A SHORT TO GROUND
- Ignition OFF.
- Depower the SRS. Refer to Supplemental Restraint System (SRS) Depowering and Repowering in the General Procedures portion of Restraint Systems.
- Disconnect: Driver Seat Side Air Bag C3134.
- Disconnect: Driver Safety Belt Buckle Pretensioner C3065.
- Disconnect: Passenger Seat Side Air Bag C3133.
- Disconnect: Passenger Safety Belt Buckle Pretensioner C3066.
- Disconnect: DCSM C3265a.
- Measure the resistance between DCSM C3265a, harness side and ground using the following chart:
- Are the resistances greater than 10,000 ohms?
Yes
GO to V2.
No
If the resistance of C3265a-G, circuit CHS02 (YE/BU) and/or C3265a-H, circuit RHS02 (BU/OG) to ground is not greater than 10,000 ohms to ground, GO to V6.
If the resistance of C3265a-J, circuit CHS01 (GY/VT) and/or C3265a-K, circuit RHS01 (WH/VT) to ground is not greater than 10,000 ohms to ground, GO to V7.
-------------------------------------------------
V2 CHECK TED CIRCUITS FOR A SHORT TO VOLTAGE
- WARNING: Make sure no one is in the vehicle and there is nothing blocking or placed in front of any air bag module when the battery is connected. Failure to follow these instructions may result in serious personal injury in the event of an accidental deployment.
- Connect the battery ground cable. Refer to Battery.
- Ignition ON.
- Measure the voltage between DCSM C3265a, harness side and ground using the following chart:
- Is voltage present on any circuits?
Yes
If voltage is present at C3265a-G and/or C3265a-H, GO to V8.
If voltage is present at C3265a-J and/or C3265a-K, GO to V9.
No
GO to V3.
-------------------------------------------------
V3 CHECK THE RESISTANCE OF THE TED AND WIRING
- Ignition OFF.
- Measure the resistance between:
- DCSM C3265a-G, circuit CHS02 (YE/BU), harness side and DCSM C3265a-H, circuit RHS02 (BU/OG), harness side.
- DCSM C3265a-J, circuit CHS01 (GY/VT), harness side and C3265a-K, circuit RHS01 (WH/VT), harness side.
- Are the resistances between 0.9 and 10 ohms?
Yes
INSTALL a new DCSM. REFER to Dual Climate Controlled Seat Module (DCSM) Dual Climate Controlled Seat Module (DCSM). CLEAR the DTCs. REPEAT the self-test.
DISCONNECT the battery ground cable.
CONNECT passenger safety belt buckle pretensioner C3066.
CONNECT passenger seat side air bag module C3133.
CONNECT driver safety belt buckle pretensioner C3065.
CONNECT driver seat side air bag module C3134.
REPOWER the SRS. REFER to Restraint Systems.
No
If the resistance between DCSM C3265a-G and C3265a-H is not between 0.9 and 10 ohms,
GO to V5.
If the resistance between DCSM C3265a-J and C3265a-K is not between 0.9 and 10 ohms,
GO to V4.
-------------------------------------------------
V4 CHECK BACKREST TED RESISTANCE
- Disconnect: Backrest TED C3034.
- Measure the resistance between backrest TED C3034 pin 1 and pin 3, component side.
- Is the resistance between 0.9 and 10 ohms?
Yes
REPAIR the circuit(s). CLEAR the DTCs. REPEAT the self-test.
DISCONNECT the battery ground cable.
CONNECT passenger safety belt buckle pretensioner C3066.
CONNECT passenger seat side air bag module C3133.
CONNECT driver safety belt buckle pretensioner C3065.
CONNECT driver seat side air bag module C3134.
REPOWER the SRS. REFER to Restraint Systems.
No
INSTALL a new backrest TED. REFER to Seat Backrest Thermo-Electric Device Seat Backrest Thermo-Electric Device. CLEAR the DTCs. REPEAT the self-test.
DISCONNECT the battery ground cable.
CONNECT passenger safety belt buckle pretensioner C3066.
CONNECT passenger seat side air bag module C3133.
CONNECT driver safety belt buckle pretensioner C3065.
CONNECT driver seat side air bag module C3134.
REPOWER the SRS. REFER to Restraint Systems.
-------------------------------------------------
V5 CHECK CUSHION TED RESISTANCE
- Disconnect: Cushion TED C3035.
- Measure the resistance between cushion TED C3035 pin 1 and pin 3, component side.
- Is the resistance between 0.9 and 10 ohms?
Yes
REPAIR the circuit(s). CLEAR the DTCs. REPEAT the self-test.
DISCONNECT the battery ground cable.
CONNECT passenger safety belt buckle pretensioner C3066.
CONNECT passenger seat side air bag module C3133.
CONNECT driver safety belt buckle pretensioner C3065.
CONNECT driver seat side air bag module C3134.
REPOWER the SRS. REFER to Restraint Systems.
No
INSTALL a new cushion TED. REFER to Seat Cushion Thermo-Electric Device Seat Cushion Thermo-Electric Device. CLEAR the DTCs. REPEAT the self-test.
DISCONNECT the battery ground cable.
CONNECT passenger safety belt buckle pretensioner C3066.
CONNECT passenger seat side air bag module C3133.
CONNECT driver safety belt buckle pretensioner C3065.
CONNECT driver seat side air bag module C3134.
REPOWER the SRS. REFER to Restraint Systems.
-------------------------------------------------
V6 CHECK CUSHION TED CIRCUITS FOR A SHORT TO GROUND
- Disconnect: Cushion TED C3035.
- Measure the resistance between:
- DCSM C3265a-G, circuit CHS02 (YE/BU), harness side and ground.
- DCSM C3265a-H, circuit RHS02 (BU/OG), harness side and ground.
- Are the resistances greater than 10,000 ohms?
Yes
INSTALL a new cushion TED. REFER to Seat Cushion Thermo-Electric Device Seat Cushion Thermo-Electric Device. CLEAR the DTCs. REPEAT the self-test.
DISCONNECT the battery ground cable.
CONNECT passenger safety belt buckle pretensioner C3066.
CONNECT passenger seat side air bag module C3133.
CONNECT driver safety belt buckle pretensioner C3065.
CONNECT driver seat side air bag module C3134.
REPOWER the SRS. REFER to Restraint Systems.
No
REPAIR the circuit(s). CLEAR the DTCs. REPEAT the self-test.
DISCONNECT the battery ground cable.
CONNECT passenger safety belt buckle pretensioner C3066.
CONNECT passenger seat side air bag module C3133.
CONNECT driver safety belt buckle pretensioner C3065.
CONNECT driver seat side air bag module C3134.
REPOWER the SRS. REFER to Restraint Systems.
-------------------------------------------------
V7 CHECK BACKREST TED CIRCUITS FOR A SHORT TO GROUND
- Disconnect: Backrest TED C3034.
- Measure the resistance between:
- DCSM C3265a-J, circuit CHS01 (GY/VT), harness side and ground.
- DCSM C3265a-K, circuit RHS01 (WH/VT), harness side and ground.
- Are the resistances greater than 10,000 ohms?
Yes
INSTALL a new backrest TED. REFER to Seat Backrest Thermo-Electric Device Seat Backrest Thermo-Electric Device. CLEAR the DTCs. REPEAT the self-test.
DISCONNECT the battery ground cable.
CONNECT passenger safety belt buckle pretensioner C3066.
CONNECT passenger seat side air bag module C3133.
CONNECT driver safety belt buckle pretensioner C3065.
CONNECT driver seat side air bag module C3134.
REPOWER the SRS. REFER to Restraint Systems.
No
REPAIR the circuit(s). CLEAR the DTCs. REPEAT the self-test.
DISCONNECT the battery ground cable.
CONNECT passenger safety belt buckle pretensioner C3066.
CONNECT passenger seat side air bag module C3133.
CONNECT driver safety belt buckle pretensioner C3065.
CONNECT driver seat side air bag module C3134.
REPOWER the SRS. REFER to Restraint Systems.
-------------------------------------------------
V8 CHECK CUSHION TED CIRCUITS FOR A SHORT TO VOLTAGE
- Disconnect: Cushion TED C3035.
- Ignition ON.
- Measure the voltage between:
- DCSM C3265a-G, circuit CHS02 (YE/BU), harness side and ground.
- DCSM C3265a-H, circuit RHS02 (BU/OG), harness side and ground.
- Is voltage present on either circuit?
Yes
REPAIR the circuit(s). CLEAR the DTCs. REPEAT the self-test.
DISCONNECT the battery ground cable.
CONNECT passenger safety belt buckle pretensioner C3066.
CONNECT passenger seat side air bag module C3133.
CONNECT driver safety belt buckle pretensioner C3065.
CONNECT driver seat side air bag module C3134.
REPOWER the SRS. REFER to Restraint Systems.
No
INSTALL a new cushion TED. REFER to Seat Cushion Thermo-Electric Device Seat Cushion Thermo-Electric Device. CLEAR the DTCs. REPEAT the self-test.
DISCONNECT the battery ground cable.
CONNECT passenger safety belt buckle pretensioner C3066.
CONNECT passenger seat side air bag module C3133.
CONNECT driver safety belt buckle pretensioner C3065.
CONNECT driver seat side air bag module C3134.
REPOWER the SRS. REFER to Restraint Systems.
-------------------------------------------------
V9 CHECK BACKREST TED CIRCUITS FOR A SHORT TO VOLTAGE
- Disconnect: Backrest TED C3034.
- Ignition ON.
- Measure the voltage between:
- DCSM C3265a-J, circuit CHS01 (GY/VT), harness side and ground.
- DCSM C3265a-K, circuit RHS01 (WH/VT), harness side and ground.
- Is voltage present on either circuit?
Yes
REPAIR the circuit(s). CLEAR the DTCs. REPEAT the self-test.
DISCONNECT the battery ground cable.
CONNECT passenger safety belt buckle pretensioner C3066.
CONNECT passenger seat side air bag module C3133.
CONNECT driver safety belt buckle pretensioner C3065.
CONNECT driver seat side air bag module C3134.
REPOWER the SRS. REFER to Restraint Systems.
No
INSTALL a new backrest TED. REFER to Seat Backrest Thermo-Electric Device Seat Backrest Thermo-Electric Device. CLEAR the DTCs. REPEAT the self-test.
DISCONNECT the battery ground cable.
CONNECT passenger safety belt buckle pretensioner C3066.
CONNECT passenger seat side air bag module C3133.
CONNECT driver safety belt buckle pretensioner C3065.
CONNECT driver seat side air bag module C3134.
REPOWER the SRS. REFER to Restraint Systems.
-------------------------------------------------