Mykey

MyKey(TM) Programming

Program a MyKey(TM)

NOTE: After a MyKey(TM) has been programmed, the remaining standard key(s) (the key[s] that is not programmed with the MyKey(TM) feature) is referred to as an "administrator key(s)" or "admin" key(s). There must always be at least one admin key.

NOTE: The MyKey(TM) feature can be cleared within the same key cycle that it was programmed. Follow the Clear MyKey(TM) procedure to clear the key of any restricted MyKey(TM) status. If the key has been cycled, an admin key is required to clear the MyKey(TM) programming.

1. Insert a programmed PATS ignition key into the ignition lock cylinder and turn the key from the OFF position to the RUN position. This key must be the one that is being programmed to the MyKey(TM) restricted status.

2. Using the message center buttons:

1. Press the SETUP button until PRESS RESET TO CREATE MYKEY appears in the message center display.

2. Press and release the RESET button. HOLD RESET TO CONFIRM MYKEY is displayed.

3. Press and hold the RESET button (for approximately 2 seconds) until MARK THIS KEY AS RESTRICTED is displayed.

4. Wait until KEY RESTRICTED AT NEXT START is displayed, then release the RESET button.

3. The MyKey(TM) feature (standard restricted features) is successfully programmed into this particular key. Make sure it is labeled for easy identification. If you would like to customize the MyKey(TM) with the audio volume limited, maximum speed limit, speed alert chimes, and AdvanceTrac(R) on/off restrictions, refer to Configuring MyKey(TM) Optional Restricted Features.
- If the vehicle is equipped with remote start, also refer to Using MyKey(TM) with Aftermarket Remote Start Systems.

Configuring MyKey(TM) Optional Restricted Features

1. To configure the MyKey(TM) optional restricted features, carry out the following:

1. Using an admin key that has not been programmed as a MyKey(TM), turn the ignition ON.

2. Press and hold the SETUP button until RESET FOR MYKEY SETUP is displayed.

3. Press and release the RESET button to display the MyKey(TM) setup menus. The first programmable feature is: MYKEY MAX MPH [80 MPH] OFF.
- If you do not want to change the status of a feature that appears, press SETUP to accept the current setting and the message center displays the next feature.

- If you want to change the status of the feature that is displayed, press RESET to turn a feature on/off (or toggle between choices). After the feature selection has been made, press and release SETUP to accept and the message center displays the next feature.

4. Repeat the process for the next features of:
- MYKEY MPH TONES 45 55 65 [OFF] (choose the desired speed for the chime to sound)

- MYKEY VOLUME LIMIT [ON] OFF (choose the audio volume to be limited to 45%)

- MYKEY ADVTRAC CTRL ON [OFF] (choose for the AdvanceTrac(R) to be automatically locked on or able to be turned on or off by the MyKey(TM) driver)

Clear MyKey(TM)

1. NOTE: This procedure is used to clear the MyKey(TM) feature on all of the keys that are programmed to the vehicle. All of the keys then operate as normal (admin) keys with no restrictions.

Using an admin key, turn the ignition ON.

2. Press SETUP until PRESS RESET TO CLEAR MYKEY appears.

3. Press and release the RESET button until HOLD RESET TO CONFIRM CLEAR is displayed.

4. Press and hold the RESET button until ALL MYKEYS CLEARED is displayed.
- A MyKey(TM) can also be cleared during the same key cycle that it was programmed by following Steps 2, 3 and 4 of this procedure.

Using MyKey(TM) with Aftermarket Remote Start System

Program Remote Start System as a MyKey(TM)

1. Enter the vehicle and close all doors.

2. Remote start the vehicle using a remote start fob.

3. Follow Steps 1-3 of the Program a MyKey(TM).

Clear MyKey(TM) with the Remote Start System

NOTE: It is possible to program all of the keys as MyKeys(TM), with the remote start system being the only admin key. This procedure clears MyKey(TM) in the event of the aftermarket remote start system being programmed as the only admin key.

1. Enter the vehicle and close all doors.

2. Remote start the vehicle using the remote start fob.

3. Follow Steps 1-4 of the Clear MyKey(TM) procedure.