Principles of Operation

Information and Entertainment System

Principles of Operation

NOTE: The Smart Junction Box (SJB) is also known as the Generic Electronic Module (GEM).

Audio Control Module (ACM)

The Audio Control Module (ACM) can be operated with the ignition in RUN or ACC. The accessory delay feature allows the audio system to be operated for a preset period of time after the ignition is turned to OFF and a front door has not been opened. The ACM (Audio Control Module) sends AC voltage audio signals to the speakers or to the amplifier, depending on vehicle configuration. The ACM (Audio Control Module) can produce its own DTCs, which can be communicated to the scan tool through the Medium Speed Controller Area Network (MS-CAN).

Front Controls Interface Module (FCIM)

The Front Controls Interface Module (FCIM) acts as a customer interface with the audio system. For vehicles without navigation, the FCIM (Front Controls Interface Module) only controls the audio functions. When a switch is pressed, a message is broadcast over the MS-CAN (Medium Speed Controller Area Network) to any module able to receive the signal.

For vehicles with navigation, the FCIM (Front Controls Interface Module) controls the audio and climate control systems. All of the switches on the panel are part of the FCIM (Front Controls Interface Module), so it is necessary for the module to send messages over the MS-CAN (Medium Speed Controller Area Network) when any switch (audio, climate control, etc.) is pressed. When a climate control switch is pressed, the HVAC module sends a message back to the FCIM (Front Controls Interface Module) to illuminate the correct switches to indicate the status of the climate control.

Front Display Interface Module (FDIM)

For vehicles without navigation, the Front Display Interface Module (FDIM) is a stand-alone module. It receives messages for all of its displays, which include:

- Audio information

- Climate control fan speed and temperature setting

- Outside air temperature

- Compass heading

For vehicles with navigation, the FDIM (Front Display Interface Module) is hardwired to the ACM (Audio Control Module). When the touchscreen is pressed, a signal is sent to the ACM (Audio Control Module), which acts on the signal either by changing the audio setting or by sending a message via the MS-CAN (Medium Speed Controller Area Network) to the module controlling the function that was selected. The audio system, navigation, and climate control video feed to the FDIM (Front Display Interface Module) is provided by the ACM (Audio Control Module). If equipped with a rear view camera, the video feed for the camera is provided by the rear view camera when the vehicle is in REVERSE.

Satellite Audio

The satellite audio system consists of the ACM (Audio Control Module), a satellite radio antenna, and a 2-piece satellite radio antenna cable. The satellite radio antenna receives digital audio signals and sends them to the ACM (Audio Control Module).

THX(R) Audio System

The THX(R) audio system provides theatre quality sound in the vehicle. Audio signals are sent from the ACM (Audio Control Module) to the audio Digital Signal Processing (DSP) module, which processes the audio signals and sends them to all of the speakers. The audio DSP (Digital Signal Processing) module uses internal software to produce a sound environment best-suited to the customer-selected setting.

Navigation System

The vehicle navigation system guides the user to a pre-entered destination. No navigation map DVD is necessary because the map data is stored directly in the ACM (Audio Control Module) hard drive. The ACM (Audio Control Module) calculates route information based on Global Positioning System (GPS) data. The GPS (Global Positioning System) antenna tracks several satellites simultaneously. The ACM (Audio Control Module) also uses vehicle speed and transmission gear selected signals received through the MS-CAN (Medium Speed Controller Area Network) to detect vehicle speed and direction, resulting in more accurate navigation tracking.

The navigation display is shown on the FDIM (Front Display Interface Module). Either the FDIM (Front Display Interface Module) touchscreen or the buttons on the FCIM (Front Controls Interface Module) can be used to interact with the navigation system.

The compass heading is derived from the GPS (Global Positioning System) antenna signal. There are no serviceable parts for the compass.

A voice recognition system allows the user to interface with the system without using the touchscreen. A microphone, located in the headliner, provides a direct input to the ACM (Audio Control Module). The same microphone is shared with the SYNC system.

Jukebox Feature

The navigation ACM (Audio Control Module) contains a 10 gigabyte on-board hard drive that is capable of storing music ripped (recorded) from a music disc. The music can be loaded into the jukebox by inserting a disc (in the correct format) and following the on-screen instructions to load the music into the ACM (Audio Control Module). The jukebox cannot rip MP3 discs.

SYNC System

The SYNC system allows interaction with several types of customer devices, including mobile phones and media devices. The system is comprised of the Accessory Protocol Interface Module (APIM), a microphone (located in the headliner), the Universal Serial Bus (USB) cable and port, and the audio input jack. The APIM (Accessory Protocol Interface Module) contains an on-board Bluetooth chipset, which enables certain wireless devices to interact with the system.

The APIM (Accessory Protocol Interface Module) consists of 2 internal modules: the Consumer Interface Processor (CIP) and the Vehicle Interface Processor (VIP). The modules are not replaceable individually, but can be flashed independently, if required.

The CIP (Consumer Interface Processor) interfaces with all of the inputs to the APIM (Accessory Protocol Interface Module). It contains an analog-to-digital-to-analog converter, as well as the Bluetooth chipset. Any consumer-available application upgrades that are available are loaded directly to the CIP (Consumer Interface Processor) through the USB (Universal Serial Bus) port.

The VIP (Vehicle Interface Processor) provides an interface between the CIP (Consumer Interface Processor) and the vehicle. Its main functions are controlling the APIM (Accessory Protocol Interface Module) power management and translating both inbound and outbound signals over the Controller Area Network (CAN).

The APIM (Accessory Protocol Interface Module) can receive inputs from the following audio sources:

- USB (Universal Serial Bus) port

- Audio input jack

- Bluetooth

The USB (Universal Serial Bus) port can be used for connecting a media device (such as an iPod(R)) with the devices available cable, or for directly plugging in a portable mass storage device (such as a "thumb drive"). When playing media files stored on a mass storage device, the SYNC system only plays files that do not have Digital Rights Management (DRM) protection. The USB (Universal Serial Bus) port can also be used for uploading new SYNC applications or their upgrades.

The USB (Universal Serial Bus) port is powered by the APIM (Accessory Protocol Interface Module), so no external power source is needed to power a device plugged into the USB (Universal Serial Bus) port if the device supports this feature.

The audio input jack can be used for connecting a media device (such as an iPod(R)) utilizing a 1/8-inch audio jack. When a device is connected through the audio input jack, only the speaker volume can be controlled by the ACM (Audio Control Module). All other functions (such as seek, fast forward, pause, etc.) must be carried out on the device itself.

The Bluetooth interface can accommodate both Bluetooth-enabled mobile phones and Bluetooth-enabled media devices. Any Bluetooth device used with the SYNC system must first be paired with the system before it is operational.

Bluetooth is a secure, short-range radio frequency that allows devices to communicate wirelessly through radio waves. The operating range of a Bluetooth signal is a maximum of 32 feet.

Only one Bluetooth phone and one Bluetooth media device can be connected to the system at any one time. If an additional device of either type is paired with the system and made active, the APIM (Accessory Protocol Interface Module) disconnects any active connections and establishes a connection with the new device.

It is important to understand that not all mobile phones have the same level of features when interacting with the SYNC system. For a list of compatible phones, refer to the SyncMyRide website.

In addition to audio information, metadata may also be sent to the APIM (Accessory Protocol Interface Module) from a device plugged into the USB (Universal Serial Bus) port. Metadata consists of such information as artist, album title, song title, and genre. The metadata is used by the APIM (Accessory Protocol Interface Module) to create indexes that can be used to sort for particular music, based on customer preference. Not all USB (Universal Serial Bus) devices can send metadata to the APIM (Accessory Protocol Interface Module) ; also, no metadata is transferred when a device is connected through the audio input jack. When a new media device is connected to the SYNC system, the APIM (Accessory Protocol Interface Module) automatically indexes the information. This may take several minutes (depending on the amount of data on the device), and is considered normal operation. When a device that was previously connected to the SYNC system is reconnected, the APIM (Accessory Protocol Interface Module) updates the index (rather than creating a new one), which reduces the amount of time needed to index the device.

The APIM (Accessory Protocol Interface Module) receives both stereo and mono sound inputs, and can also transmit both stereo and mono sound. The mono function is used to receive the microphone input, and to send sound to the ACM (Audio Control Module) for voice prompts, the Text-To-Speech (TTS) feature, ring tones, and any audio received through a connected mobile phone. The TTS (Text-To-Speech) feature speaks information so that it does not have to be read from the display.

The Global Positioning System Module (GPSM) provides vehicle location for real-time traffic reports and re-routing, and for identifying vehicle location in the event of a collision. The vehicle location information is broadcast to the APIM (Accessory Protocol Interface Module) over the MS-CAN (Medium Speed Controller Area Network).

The APIM (Accessory Protocol Interface Module) communicates on the MS-CAN (Medium Speed Controller Area Network) and High Speed Controller Area Network (HS-CAN). Communication with the scan tool is established through the HS-CAN (High Speed Controller Area Network).

Voice Recognition For Vehicles With Navigation And The SYNC System

When the audio system enters voice recognition mode, the ACM (Audio Control Module) initially controls the voice recognition feature. The microphone is wired directly to the APIM (Accessory Protocol Interface Module), which relays the microphone input to the ACM (Audio Control Module) through dedicated wiring. If the first command spoken is part of the ACM (Audio Control Module) voice recognition set, the ACM (Audio Control Module) retains control of the voice recognition and takes the appropriate action(s). If the first command spoken is part of the APIM (Accessory Protocol Interface Module) voice recognition set, the ACM (Audio Control Module) shuts off its own voice recognition and broadcasts a Controller Area Network (CAN) message to the APIM (Accessory Protocol Interface Module), transferring the voice recognition to the SYNC system and providing the voice command that was spoken. The ACM (Audio Control Module) controls the voice engine for the base audio, navigation, and climate control systems. The APIM (Accessory Protocol Interface Module) controls the voice engine for the SYNC system (USB (Universal Serial Bus) port, audio input jack, Bluetooth).

AM/FM Antenna

The AM/FM antenna is located on the rear window glass. An antenna isolator module is utilized to filter out interference from the rear defrost grid. A co-axial antenna cable connects the antenna isolator module to the ACM (Audio Control Module).

Satellite Radio/Global Positioning System (GPS) Antenna

The satellite radio antenna receives digital audio signals and transfers them to the ACM (Audio Control Module) through the satellite radio antenna cable.

If the vehicle is equipped with navigation, a combination satellite radio/GPS (Global Positioning System) antenna is utilized. This antenna receives both digital audio signals and GPS (Global Positioning System) information. The compass heading is derived from the GPS (Global Positioning System) signal.

Steering Wheel Controls

The steering wheel controls consist of a series of resistors. Each steering wheel control switch function corresponds with a specific resistance value within the switch. When a switch is pressed, the ACM (Audio Control Module) (or the APIM (Accessory Protocol Interface Module)) monitors the change in reference voltage to determine the requested function.

Subwoofer

The subwoofer speaker is powered by the audio DSP (Digital Signal Processing) module. The enable/clip detection circuit carries out 2 functions: to turn the amplifier on, and to indicate to the ACM (Audio Control Module) when the subwoofer output distortion signal reaches a damaging level. The ACM (Audio Control Module) then clips the audio output signal to prevent damage to the subwoofer.

Noise Suppression Equipment

The radio frequency suppression equipment reduces interference transmitted through the speakers by the engine ignition and electrical systems. When installing any new radio suppression equipment components, make sure that a good contact is made at all connections. For this vehicle, an engine bonding strap from the engine block to the RH strut tower, and a radio interference capacitor (located on the LH side of the parcel shelf) are utilized.

Audio Signals

Stereo signals contain left and right channel information, and are used for most audio signals, including:

- ACM (Audio Control Module) output to speakers

- ACM (Audio Control Module) audio output to audio DSP (Digital Signal Processing) module

- Audio DSP (Digital Signal Processing) module output to speakers

- APIM (Accessory Protocol Interface Module) audio output to ACM (Audio Control Module)

A mono signal is used for the microphone input to the APIM (Accessory Protocol Interface Module). A mono signal is also used for the voice prompts, the Text-To-Speech (TTS) feature, ring tones, and any audio received through a connected mobile phone. These audio signals are output from the APIM (Accessory Protocol Interface Module) to the ACM (Audio Control Module). The mono and stereo outputs from the APIM (Accessory Protocol Interface Module) utilize separate circuits.

A digital signal is used to transmit data from a media device connected through the USB (Universal Serial Bus) port to the APIM (Accessory Protocol Interface Module). The APIM (Accessory Protocol Interface Module) then converts the signal to analog and relays the signal to the ACM (Audio Control Module).

A wireless signal is used to broadcast audio signals from a Bluetooth device to the APIM (Accessory Protocol Interface Module), which converts the wireless audio signal to analog and relays it to the ACM (Audio Control Module).

Network Communication

The following audio system components communicate via the MS-CAN (Medium Speed Controller Area Network) :

- ACM (Audio Control Module)

- Navigation ACM (Audio Control Module)

- FCIM (Front Controls Interface Module)

- FDIM (Front Display Interface Module) (vehicles without navigation)

- Audio DSP (Digital Signal Processing) module

- APIM (Accessory Protocol Interface Module)

- GPSM (Global Positioning System Module)

There are numerous messages internal to the audio system. The functions of these messages include (but are not limited to):

- Changing the audio source

- Changing equalizer settings

- Updating the FDIM (Front Display Interface Module) display

- Dialing phone numbers from the FCIM (Front Controls Interface Module) or FDIM (Front Display Interface Module)

In addition, the following messages are utilized by the audio system in conjunction with systems outside of the audio system:

Audio System