Seat Belt, Rear 3 Point - Installation
89mazda08Category
14
Applicable Model/s (See Below)
Subject INSTALLATION OF REAR 3-POINT SEAT BELT
Bulletin No. 073/89
Issued 11/8/89
Revised
DESCRIPTION
Mazda has established the 3-Point Seat Belt Kit as a service part for the 1981-1985 GLC, 1979-1986 GLC Wagon, 1986-87 323, 1987 323 Wagon, 1979-1982 626, 1983-1987 626, and 1986-1988 RX-7.
If the installation of such kit is required by a customer, please refer to the installation procedures described in this bulletin.
APPLIED MODELS & KIT PART NUMBERS
INSTALLATION PROCEDURES
^ A. GLC 1981-1985 MODEL YEAR GLC WAGON 1979-1986 MODEL YEAR
1. Remove the rear seat cushion.
2. Remove the rear outer and inner lap belts.
3. Remove the rear pillar trim caps.
4. Install the new rear outer, inner lap belts and shoulder belts (as shown in illustration).
NOTE: ^ Spacer Thickness (*) 0.2 in. (5 mm)
^ Specified Tightening Torque (**) 28-58 ft.lb. (3.9-8.0 m-Kg, 38-78 N-m)
5. Reinstall the rear seat cushion.
^ B. 323 1986-1987 MODEL YEAR 323 WAGON 1987 MODEL YEAR
1. Remove the rear seat cushion.
2. Remove the rear outer and inner lap belts.
3. Remove the rear pillar trim caps.
4. Install the new rear outer, inner lap belts and shoulder belts (as shown in illustration).
NOTE: Spacer Thickness (*) (Use correct spacer specificafly designated for your vehicle)
3HB ........ 0.47 in. (12 mm)
4SD ........ 0.59 in. (15 mm)
SHB ........ 0.47 in. (12 mm)
Wagon .... 0.39 in. (10 mm)
^ Specified Tightening Torque (**) 28-58 ft.lb. (3.9-8.0 m-Kg, 38-78 N-m)
5. Reinstall the rear seat cushion.
^ C. 626 1979-1982 MODEL YEAR
1. Remove the rear seat cushion and seat back (except folding seat).
2. Remove the rear outer and inner lap belts.
3. Remove the rear package tray and make 0.98 in. (25 mm) diameter holes in it as shown.
4. Install the new rear outer and inner lap belts and shoulder belts as shown.
NOTE: ^ Spacer thickness: (*) 0.39 in. (10 mm)
^ Specified tightening torque: (**) 28-58 ft.lb. (3.9-8.0 M-Kg,38-78 N-m)
5. Install the rear seat cushion and seat back. (Except folding seat)
^ D. 626 1983-1987 MODEL YEAR.
1. Remove the rear seat cushion.
2. Remove the rear seat back. (Except 5-Door Hatchback or folding seat)
3. Remove the rear outer and inner lap belts.
4. Remove the rear pillar trim caps. (5-Door Hatchback)
5. Remove the rear package tray and make 0.98 in. (25 mm) diameter holes in it as shown in illustration. (Except 5-Door Hatchback)
6. Install the rear package tray (except 5-Door Hatchback).
7. Reinstall the rear seat. (except 5-Door or folding seat)
8. Install the new rear outer and inner lap belts and shoulder belts as shown in illustration.
NOTE: ^ Spacer Thickness (*) 0.20 In. (5 mm) (2HT & 4SD) 0.39 In. (10 mm) (5HB)
^ Specified tightening torque: (**) 28-58 ft.lb. (3.9-8.0 m-Kg, 38-78 N-m)
^ E. RX-7 1986-1988 MODEL YEAR
1. Remove the rear seat cushion.
2. Remove the rear outer and inner lap belts.
3. Drill 1.18 in. (30 mm) diameter holes in the rear pillar trim as shown.
4. Install the new rear outer and inner lap belts and shoulder belts.
NOTE: ^ Spacer Thickness (*) 0.39 in. (10 mm)
Specified tightening torque: (**) 28-58 ft.lb. (3.9-8.0 m-Kg, 38-78 N-m)
5. Install the rear seat cushion.