Vehicle Damage Warnings
ELECTRICAL AND ELECTRONICElectronic components used in automotive computers are designed to operate at low voltages (3 - 5V) and are extremely susceptible to damage caused by static electrical discharge. Voltages as low as 12V can damage computer circuits. By comparison, it takes as much as 4,000 volts of static discharge for a person to even feel the "ZAP."
There are several ways to become statically charged; charging by friction and charging by induction are the most common. Friction between organic materials (such as cotton or leather) and synthetics (such as plastic, vinyl, or glass) will generate static charges as great as 25,000 volts. This can happen by simply sliding across a car seat or by wearing a cotton shirt under a coat made of synthetic materials. Charging by induction occurs when a person standing near a highly charged object (strong magnetic field such as a transformer) momentarily touches ground. Like charges are displaced to ground, leaving the person highly charged with opposite polarity. Static charges are gradually equalized by moisture in the air, but are retained much longer when humidity is low.
USE OF PROPER TOOLS AND TESTING PROCEDURES
Unless use of an analog meter is specified by a testing procedure, use a digital volt/ohm meter (DVM) with a minimum 10 megohms internal impedance when testing a PCME or related components. Analog meters have low internal impedance and cause circuit "loading" in low voltage circuits, resulting in inaccurate measurements and possible damage to components.
Always follow recommended testing procedures. Never ground or apply voltage to a circuit unless specified by a testing procedure. The PCME provides a regulated constant low voltage source to some circuits which may require a minimum resistance (impedance) to operate. Directly grounding or applying battery power to these circuits could damage the PCME and cause a system failure.
PRECAUTIONS TO AVOID ELECTRONIC COMPONENT DAMAGE
^ Discharge static electrical charges before handling sensitive parts. Touch ground or maintain a ground connection to a bare skin area like the wrist when servicing sensitive parts.
^ Never touch PCME connector pins, integrated circuit connector pins, or soldered components on PCME circuit boards.
^ Always ensure the battery is properly connected before attempting to start engine.
^ Do not disconnect battery when the engine is running.
^ Fully release connector locks prior to disconnecting. Ensure connectors are fully seated and all insulators and shields are in place when reinstalling.
^ Never connect or disconnect electrical connections with the ignition switch ON unless specifically directed to do so in a test procedure.
^ To disable the ignition system, unplug primary connections or ground ignition wire(s) to cancel desired cylinder(s). NEVER disconnect secondary leads to disable the ignition system.
^ Do not use a self powered test lamp to check continuity.
^ Do not create arcing to check the continuity of a circuit.
^ When charging a battery, be sure battery cables are disconnected.
^ When replacing electronic components, disconnect battery ground.
NOTE: Before removing battery ground, access trouble codes. PCME memory is erased if ground cable is removed.
^ When measuring voltage at the PCME harness connector, disconnect harness connector first, then turn ignition ON as necessary.
^ To prevent deforming PCME harness connectors, do not probe terminals directly. Instead, insert a pin from the harness side and perform measurements through pin.
^ Avoid getting water on fuel, control system and ignition system components.
^ Fuel and engine control system wiring should be at least 4 inches from ignition wires.
^ Never pierce ignition leads or insulator boots to connect timing lights or analyzers. Use proper adapters.
^ When removing a spark plug wire, twist the boot one quarter turn and pull on boot only. Never pull directly on leads.
^ Always use 12V batteries as a power source.
^ Never apply battery power to a component unless directed to do so in a test procedure.
^ Do not try to disassemble the PCME.
^ Never use a booster/starter which has a voltage rating above 12V to start engine.
^ Before performing electrical welding (for instance, spot welding), disconnect the battery, climate control, injection, cruise control, PCME, and radio.
^ In cases when temperatures may exceed 176°F (80°C), (example: infra-red spray booth), remove all electronic control units.
^ Batteries contain acid and produce explosive gas (hydrogen). Avoid creating sparks near battery.
ENGINE AND EXHAUST
On vehicles with catalytic converters, the following conditions must be observed:
^ Use only "UNLEADED FUEL."
^ Avoid running out of fuel.
^ In case of poor engine operation (misfiring), avoid driving the vehicle and correct the problem as soon as possible.
^ Do not disconnect any spark plug wires with the engine running.
^ Avoid push starting the vehicle.
^ If running on a dynamometer, make sure the catalytic converter is well ventilated.
^ To avoid of burns, use caution when working near the catalytic converter.
Do not use silicone based products on an oxygen sensor equipped vehicle. These products may contaminate the sensor.
When performing a compression test, remove the fuel pump relay fuse and disconnect power to the ignition. This will stop fuel flow to the injectors and prevent engine from starting.