Radio, Stereo, and Compact Disc: Testing and Inspection
SETTING AUDIO CODE NUMBERFig. 1 Entering Radio Coded Theft Protection:
1. With the ignition switch in the ACC position, turn OFF the audio unit.
2. Press and hold the SCAN and AUTO-M buttons simultaneously until "code" appears on the display (approx. 1.5 seconds).
Fig. 2 Clearing Radio Coded Theft Protection:
3. Press the SCAN and AUTO-M buttons again until bars appear on the display.
Note: Input the code number within 10 seconds, or the display will be deleted. If deleted, repeat the procedure from Step 1. Complete steps 1-3 within 10 seconds, or the setting procedure will be canceled.
Fig. 3 Entering Coded Theft Protection:
4. Record the code number before attempting to input it. If the number is input and then forgotten, it cannot be canceled and the audio unit will be inoperative if ever disconnected. While the bars are displayed, input the personally selected code number by pressing preset channel buttons 1,2, 3, and 4. Use 1 for the first digit, 2 for the second, 3 for the third, and 4 for the last digit. Example: Inputting code number 3543.
Press 1 four times. 2 six times, 3 five times, and 4 four times.
Note: Record the code number within 10 seconds, or the display will be deleted. If deleted, repeat the procedure from Step 1.
Fig. 4 Setting Coded Theft Protection:
5. With the code number displayed. press and hold the SCAN and AUTO-M buttons until a beep is heard (approx. 1.5 seconds). "Code" will be displayed for approximately 5 seconds, and after it disappears, the code number is set.
Note: If "Err" (error) appears on the display, repeat the procedure from Step 1. If input error is repeated three times, temporarily turn OFF the ignition and restart the procedure.
CANCELLING AUDIO CODE NUMBER
1. With the ignition switch in the ACC position, turn OFF the audio unit.
2. Press and hold down the SCAN and AUTO-M buttons simultaneously until "code" flashes on the display.
3. Press SCAN and AUTO-M buttons again until bars appear on the display.
Note: Complete Steps 1-3 within 10 seconds, or the canceling procedure will be canceled.
4. While the bars are displayed, input the current code number as described in Setting Code Number, Step 4.
5. With the code number on display, press and hold the SCAN and AUTO-M until a beep is heard (approx. 1.5 seconds). "Code" will be displayed for approximately 5 seconds and the code number is canceled. The display then resumes the code number setting condition.
Note: Input the code number within 10 seconds, or the display will be deleted. If deleted, repeat the procedure from Step 1.
- If "Err" (error) appears on the display, repeat the procedure from Step 1.
- If "code" appears on the display, the code number is not canceled. Repeat the procedure from Step 3.
- Three consecutive errors will activate the antitheft operation, and the audio unit will be rendered completely inoperative. In this case, consult Fujitsu Ten Service Co.
- Error includes turning the ignition switch OFF and disconnection of the audio unit connectors.
RESETTING AUDIO CODE NUMBER
When the code number cancel operation is completed, set a new code number as follows.
1. Press and hold the SCAN and AUTO-M buttons until bars appear on the display.
2. Record the code number before attempting to input it. If the number is input and forgotten, it cannot be canceled and the audio unit will be rendered inoperative if ever disconnected. While the bars are displayed, input the new code number as described under "Setting Code Number".
Note: Complete Steps 1-3 within 10 seconds, or the setting procedure will be cancelled.
3. Press and hold the SCAN and AUTO-M buttons simultaneously until a beep is heard and "code" appears on the display (approx. 1.5 seconds). "Code" will flash for 15 seconds, then disappear to indicate that the code number is set.
4. If "Err" (error) appears on the display, repeat the procedure from Step 1.
Note: Error includes turning the ignition switch OFF and disconnecting the audio unit connectors.
- Three consecutive errors will activate the anti- theft operation, and the audio unit will be completely inoperative. In this case, consult Fujitsu Ten Service Co.
CANCELLING ANTI-THEFT OPERATION
Note: The audio system becomes inoperative under the following conditions if the code number has been input.
1. A battery cable is disconnected.
2. Battery is discharged.
3. Audio unit audio connectors are disconnected.
To resume audio system operation, the anti-theft operation must be deactivated.
1. Turn the ignition switch to the ACC position. Code" will flash on the display.
2. Press the SCAN and AUTO-M buttons simultaneously until bars appear on the display.
3. While the bars are displayed, input the correct preselected code number as described in Setting Code Number, Step 4,
4. Press and hold the SCAN and AUTO-M buttons until a beep is heard and "code" appears on the display (approx. 1.5 seconds). "Code" will flash for 5 seconds, then disappear to indicate that the system is operative.
Note: If "Err" (error) appears on the display, repeat the procedure from Step 1.
- Error includes turning the ignition switch OFF and disconnecting the audio unit connectors.
- Three consecutive errors will activate the antitheft operation, and the audio unit will be rendered completely inoperative. In this case, consult Fujitsu Ten Service Co.