Disassembly

Disassembly

Components

Automatic Transmission (Part 1):

Automatic Transmission (Part 2):

Disassembly procedure

1. Remove the torque converter, and immediately turn it so that the hole faces upward. This will help to keep any remaining fluid from spilling.





2. Assemble the SSTs.





3. Mount the transmission on the SSTs.
4. Turn down the oil pan in order to gather any material.

Caution: Be careful not to scratch the mating surfaces of the control valve body cover and the transmission case.

5. Remove the oil pan and the gasket.
6. Examine any material found in the oil pan or on the magnet to determine the condition of the transmission.
^ If large amounts of material are found, replace the torque converter and carefully inspect the transmission for the cause.





7. Install the oil pan with a few bolts to protect the control valve body.





8. Remove the turbine sensor and the vehicle speed sensor (VSS).
9. Remove the O-ring from the turbine sensor and the VSS.





10. Remove the TR switch.

Caution: Denting the parking components will reduce the performance of the transmission. When handling the components, be careful not to drop them.





11. Remove the extension housing as shown in the figure.





12. Remove the bearing from the extension housing.





13. Remove the oil seal from the extension housing using a flathead screwdriver.





14. Remove the output shaft component and the bearing.





15. Remove the seal rings from the output shaft component.





16. Remove the parking pawl, shaft, spring, and the spacer.





17. Remove the actuator support.

Note: Do not reuse the oil pan installation bolts as they are coated.

18. Remove the oil pan.





19. Disconnect the harness component as shown in the figure.





20. Remove the bolts as shown in the figure.

Note:
^ When removing control valve body, be careful not to drop the manual valve.
^ Do not move the manual valve in the direction of arrow to prevent the pin for the manual valve rotation prevention from falling from the control valve body.





21. Remove the control valve body.





22. Remove the harness component.
23. Remove the O-ring from the harness component.





24. Remove the roll pin using a pin punch.





25. Remove the roll pin.





26. Remove the manual shaft, manual plate and parking rod.





27. Remove the detent spring.

Caution: Scratching the transmission will reduce the performance of the transmission. When removing the oil seal, be sure to prevent the flathead screwdriver from contacting the transmission.





28. Remove the oil seal using a flathead screwdriver.





29. Remove the torque converter housing as shown in the figure.





30. Remove the O-ring from the input shaft.





31. Remove the bolts as shown in the figure.





32. Install the SST to the oil pump.
33. While pulling the oil pump shaft upward, remove the oil pump by sliding the weight of the SST.
34. Remove the SST from the oil pump.
35. Remove any old sealant from the oil pump.





36. Remove the bearing from the oil pump.





37. Remove the O-ring from the oil pump.





38. Remove the seal rings from the oil pump.





39. Remove the input shaft.





40. Remove the bearing and the reverse and high clutch drum.





41. Remove the bearing from the reverse and high clutch drum.





42. Remove the high clutch hub and the bearing race.





43. Remove the bearing, front sun gear, and the bearing race.
44. Inspect the 2-4 brake operation.





45. Remove the seal ring and the sleeve.

Caution: Be sure to center the SSTs on the transmission case. Otherwise, the return spring can be damaged.





46. Install the SSTs to the transmission case.

Caution: Do not compress the 2-4 brake retainer excessively. Doing so can damage the return spring.





47. Compress the 2-4 brake retainer using the SST.
48. Remove the snap ring.
49. Remove the SSTs.





50. Remove the 2-4 brake retainer and the return spring.





51. Remove the 2-4 brake piston from the 2-4 brake retainer.





52. Remove the seal rings from the 2-4 brake piston.





53. Remove the carrier component, plates of the 2-4 brake, and the N-spring.

Note: Remove the low one-way clutch inner race by loosening the bolts evenly and gradually. Otherwise, the low one-way clutch inner race will slant and become irremovable.





54. Remove the bolts.





55. Remove the bearing and the low one-way clutch inner race.





56. Remove the seal rings from the low one-way clutch inner race.