Back Window Glass: Service and Repair
REAR WINDOW GLASS REMOVAL1. For the Sedan, remove the following parts:
1. Remove the headliner.
2. Remove the rear package trim.
2. For the 5-Door, remove the following parts:
1. Remove the rear wiper arm and blade.
2. Remove the liftgate lower trim.
3. Remove the liftgate side trim.
4. Remove the liftgate upper trim.
3. For the Sport Wagon, remove the following parts;
1. Remove the rear wiper arm and blade.
2. Remove the liftgate lower trim.
3. Remove the liftgate side trim.
4. Remove the liftgate upper trim.
5. Remove the rear wiper motor.
4. Apply protective tape along the edge of the body to protect it from damage.
5. Cut the lip of the rear window molding using a razor.
WARNING: Using a razor with bare hands can cause injury. Always wear gloves when using a razor.
NOTE: The rear window molding is a replacement part.
Not Reusing Rear Window Glass
NOTE: For the areas of the sealant that are difficult to cut, use a SST (piano wire) and follow the procedure under "Reusing Rear Window Glass."
1. Use the tool like that shown in the figure, and insert the blade into the sealant.
2. Pull through the sealant around the edge of the glass.
3. Remove the rear window glass.
Reusing Rear Window Glass
NOTE: Before removing the rear window glass from the body, mark the position of the glass by affixing tape to the glass and body panel.
1. Make a hole through the sealant, avoiding pins, from the inside of the vehicle using an awl.
2. Pass the SST (piano wire) through the hole.
WARNING: Using the SST (piano wire) with bare hands can cause injury. Always wear gloves when using the SST (piano wire).
3. Wind each end of the SST (piano wire) around a bar.
NOTE: Use a long sawing action to spread the work over the whole length of the SST (piano wire) to prevent it from breaking due to localized heating.
4. Fix one end of the SST (piano wire), and while pulling the other end, cut the sealant around the rear window glass.
5. Remove the rear window glass.
6. Remove the pins from the glass.
7. Remove the rear window molding from the glass.
REAR WINDOW GLASS INSTALLATION
CAUTION: To prevent the sealant from cracking or the glass from being pushed out by air pressure if a door is closed, open all of the windows and leave them open until the sealant has hardened.
1. Cut away the old sealant using a razor so that 1 - 2 mm {0.04 - 0.07 in} thickness of sealant remains around the circumference of the frame.
WARNING: Using a razor with bare hands can cause injury. Always wear gloves when using a razor.
2. If the sealant has come off completely in any one place, apply some primer after degreasing, and allow it approximately 30 minutes to dry. Then put on new sealant to create a 2 mm {0.08 in} layer.
3. Clean and degrease an approximately 50.0 mm {1.97 in} wide strip along the perimeter of the glass and the bonding area on the body.
4. Install the dams and spacer as shown in the figure. (Sport Wagon only)
5. Install the molding as shown in the figure.
6. Use only glass primer on the glass. Allow it to dry for approximately 30 minutes.
CAUTION: Keep the area free of dirt and grease, and do not touch the surface or the primer may not properly bond to the surface of the glass and body, which may cause leaks to occur.
7. Apply sealant to the area of the glass surface as shown in the figure.
8. Set the position of the front windshield glass and insert a pin into the body. Install the glass.
9. Verify that the gap of the upper part is 7.3 mm {0.29 in} and the A pillar part is 6.8 mm {0.27 in}. (Only for Sedan)
10. Keeping the measurement of the molding lip gap within specification, press completely along the perimeter of the glass.
11. For the Sedan, install the following parts:
1. Install the headliner.
2. Install the rear package trim.
12. For the 5-Door, install the following points.
1. Install the rear wiper motor.
2. Install the liftgate lower trim.
13. For the Sport Wagon, install the following points.
1. Install the rear wiper motor.
2. Install the liftgate lower trim.
3. Install the liftgate side trim.
4. Install the liftgate upper trim.
14. Allow the sealant to harden completely.
Sealant hardening time: 24 hours.