D. Generate SCN Codes
1. Click on "Coding" button on the top of the window (Figure 5).
2. Enter data into required fields (Figure 6).
(A) Enter VIN into "FIN/VIN" window.
(B) Enter PKW in the "Category" box.
(C) Click on "Other control unit."
(D) Enter respective SA Codes in the "Plus SA codes" & "Minus SA codes" window ONLY IF you are installing a Dealer installed accessory.
(E) Click on the button "F2 Enter Control Unit Data."
Note:
The SA Code needs to be entered and coded only once when the accessory is installed for the first time. Do not attempt to add/subtract a SA Code if you are only performing an Instrument Cluster replacement.
The SA Codes for each Dealer installed accessory is as follows:
Navigation
2006 Model Year and Older -
^ 164 & 251 - Plus SA Code '530' & Minus SA Code "528" & "245"
2007 Model Year and Newer -
^ 164 & 251 - Plus SA Code "530" & Minus SA Code "528" & "245"
^ 164x - NO SA CODE REQUIRED - The NAVI information should already be visible in the IC after the NAVI unit has been installed, configured and driven a short distance, If the NAVI Menu is not visible, simply SCN Code the Instrument Cluster without adding any SA Code numbers. The SCN Code will ensure that the NAVI information will be displayed.
Telephone
2006 Model Year and Older -
^ 164 & 251 - Plus SA Code "o05" <-- This is Letter "o", Number "0" and Number "5"
2007 Model Year and Newer -
^ 164 & 251 - No SA Code Needed - Tel Menu active in IC from factory
^ 164x - NO SA CODE REQUIRED - The TEL information should already be visible in the IC after the TEL unit has been installed. If the TEL Menu is not visible, simply SCN Code the Instrument Cluster without adding any SA Code numbers. The SCN Code will ensure that the TEL information will be displayed.
Note:
Refer to the following Instructions for Dealer accessory installation procedure:
^ Model 164: 1-1-82.70/435 & 1-1-82.85/441
^ Model 251: 1-1-82.70/454 & WIS AR82.58-P-7373RT
(F) Enter the Part Number of the control unit (Figure 7).
(G) Enter the Check Digit [1] (Figure 7).
3. Generate SCN Coding Information.
(H) Click "F3 Query" button (Figure 7).
Note:
If you see the following message (Figure 7a) pop-up after pressing the "F3 Query" button(Step 3), this means that the SA Code that you have entered has already been reflected in the vehicle record Because the SA Code is already in the vehicle record, it cannot be entered in again. Please delete the SA Code that was entered (Figure 6, Arrow D) and Click the "F3 Query" button again to generate the SCN Code. The SCN Code will be generated and it will reflect the Dealer Fit Accessory that has been installed into the vehicle.
Note:
If you see the following message type (Figure 7b) you have not put the correct Plus/Minus SA Code into the fields. Please refer to the information above and re-enter the SA Plus/Minus as required.
4. Display SCN Coding Information. (Figure 8) (I) Click the "OK" button.
(J) SCN Coding Information will then be displayed.
I. Print Out Method
(K) If you are SCN coding via Print Out Method, click on "F11 Print" to print the information, and continue onto section "E".
II. CD-Burn Method
(L) If you are SCN coding via CD-Burn Method, insert the CD into the CD Burner, then click on "F7 Start burning program". Your designated burning program will start. Proceed to step 5.
Note:
If you are starting the CD burning process for the first time on the computer, DO NOT click on "F7 Start burning program". Please have your IT personnel set up the burning software configuration.
Note for IT:
Burning Software Configuration: Select "F6 Select burning software". Then a window will open asking for you to select the preferred burning software. Search through the drive until you select the program (Ex. Nero.exe or Roxie.exe) of your choice. Click on "Save". The technician may now continue with step 4(L). To change the preferred burning software at anytime, repeat this procedure.
5. Burning the SCN Coding information.
(M) Look for the files in the following directory of your computer (Figure 9). C :\userdata\csd\writefil\create\flashfil\Pkw\XXX.XXX\VIN Number
Note:
The XXX.XXX is characters 4-9 of the VIN.
Example: For Vin 4JGBB86EX6A00283, the directory will be:
C :\u serdata\csd\writefil\create\flashfil\Pkw\BB8.6EX\4JGBB86EX6A00283\
(N) Only burn the two files located in the specified VIN directory (Figure 9).
(0) After the CD is burned, return to the SDS with the CD, and continue with section "E".
6. Select "Perform SCN Coding", Press "F3" (Figure 10).
7. A. If you are SCN Coding via Print Out Method, press "F4" (Figure 11) and continue to sub-category A" of this section.
B. If you are SCN coding via CD-Burn Method, insert the CD in the SDS, then press "F3" (Figure 11) and continue on to sub-category "A" of this section.