AZ82.70-P-0001-04PA Retrofit Wiring Harness
AZ82.70-P-0001-04PA Retrofit Wiring Harness
- with CODE (494) USA version
- except CODE (810) Sound system
Special Tools:
1 Disconnect coupling housing (56) from plug (55) of SDAR wiring harness (50).
The coupling housing (56) is still required.
2 Disconnect coupling housing (62) from plug (61) of SDAR wiring harness (50).
The coupling housing (62) is still required.
3 Disconnect coupling housing (59) from plug (58) and pin wake-up pin (57) of wake-up line branch-off (53) of SDAR wiring harness (50) into contact cavity 1 of coupling housing (59).
Component Identification:
4 Connect coupling housing (59) to plug (58) of wake-up line branch-off (53) of SDAR wiring harness (50).
5 Expose UPCI preinstallation connector (44), remove lock (47) of UPCI preinstallation connector (44) of onboard wiring harness (46) and disconnect UPCI preinstallation connector (44) from 32-pin contact carrier (49).
6 Unpin blue/black line (48) of on-board wiring harness (46) from contact cavity 24 of 32-pin contact carrier (49) and pin into contact cavity 1 of coupling housing (62).
7 Pin wake-up pin (57) of wake-up line branch-off (53) of SDAR wiring harness into contact cavity 24 of 32- pin contact carrier (49).
8 Push 32-pin contact carrier (49) into UPCI preinstallation connector (44) and attach lock (47) to UPCI preinstallation connector (44) of on-board wiring harness (46).
9 Connect coupling housing (62) to plug (61) of wake-up line branch-off (53) of SDAR wiring harness.
10 Secure connector comprising coupling housing (59) and plug (58), and connector comprising coupling housing (62) and plug (61) of wake-up line branch-off (53) of SDAR wiring harness together to UPCI preinstallation connector (44) of on-board wiring harness (46) using self-adhesive felt as per picture.
Component Identification:
11 Position foam material around UPCI preinstallation connector (44) and secure UPCI preinstallation connector (44) to on- board wiring harnesses as per picture.
12 Route wake-up line branch-off (53) of SDAR wiring harness (50) as per picture and secure to on-board wiring harnesses.
13 Route SDAR wiring harness (50) as per picture and secure to on-board wiring harnesses.
14 Route ground connection (51) of SDAR wiring harness (50) as per picture, connect to ground (right wheelhouse in luggage compartment) (W7) and secure to on-board wiring harnesses.
15 Route power supply line branch-off (52) of SDAR wiring harness (50) to rear SAM control unit with fuse and relay module (N10/2) in luggage compartment as per picture and secure to on-board wiring harnesses together with antenna extension line (8).
Steps 15 and 16 below only need to be carried out for vehicles on which slot 5 on the rear SAM control unit with fuse and relay module (N10/2) is factory-fitted with an on-board 2-pin green connector (64).
16 Disconnect on-board 2-pin green connector (64) from slot 5 of rear SAM control unit with fuse and relay module (N10/2).
17 Unpin on-board red/black line (65) from on-board 2-pin green connector (64) and pin into contact cavity 2 of coupling housing (56).
The on-board 2-pin green connector (64) is no longer required.
18 Connect coupling housing (56) to plug (55) of power supply line branch-off (52) of SDAR wiring harness (50).
19 Connect power supply connector (54) of power supply line branch-off (52) of SDAR wiring harness (50) to slot 5 of rear SAM control unit with fuse and relay module (N10/2).
20 Secure connector comprising coupling housing (56) and plug (55), and power supply line branch-off (52) of SDAR wiring harness (50) to on-board wiring harnesses as per picture.
21 Fit 7.5 amp fuse at fuse slot 16 of rear SAM control unit with fuse and relay module (N10/2).
Depending on the special equipment, a 7.5 amp fuse may already be fitted at fuse slot 16 of the rear SAM control unit with fuse and relay module (N10/2).
The connector (63) is connected to the SDAR control unit at a later stage.