GF82.70-P-2008RIJ Setting Up/Ending Phone Call, Function

GF82.70-P-2008RIJ Setting Up/Ending Phone Call, Function
- with CODE (527) COMAND APS with single DVD drive (with navigation)
- basic telephony

Function requirements
^ Status "Circuit 30 ON" or "Circuit 15R ON"
^ Mobile phone and COMAND operating, display and controller unit (A40/3) switched on
^ Mobile phone system operating error-free
^ One mobile phone network is available in sufficient strength and quality
^ Mobile phone adapter cable connected to the communications control unit (N123/6) via the cell phone separation point (X39/37)
^ Compatible mobile phone connected to preinstalled adapter cable or Bluetooth-compatible mobile phone in vehicle and authorized by COMAND operating, display and controller unit
^ "vCards" can be loaded into the COMAND operating, display and controller unit from an SD card

Various mobile phones can be connected to the communications control unit via the cell phone separation point using the preinstalled adapter cable.

A Bluetooth-compatible mobile phone can only be operated in the vehicle when a mobile phone is not connected to the cell phone separation point or the adapter cable.
The Bluetooth mobile phone must also be authorized at the COMAND operating, display and controller unit and support Hands Free Profile (HFP) 1.0 or 1.5. More information is available under:
- www.mercedes-benz-mobile.com

With a mobile phone operated with Bluetooth, read access to the telephone book in the mobile phone is possible when the mobile phone supports the Bluetooth Profile Phonebook Access Profile (PBAP).

General
The mobile phone can be used by the user to initiate or terminate a telephone call to another person in the cellular telephone system network or the fixed-line network.
The establish call and terminate call function consists of the following subfunctions:
^ Function sequence, establish call via mobile phone buttons
^ Function sequence, establish call via telephone buttons or keypad on COMAND operating, display and controller unit
^ Function sequence, establish call via left multifunction steering wheel button group (S110) and right multifunction steering wheel button group (S111)
^ Function sequence, establish call via voice control system (VCS [SBS])
^ Function sequence, establish call via navigation mode
^ Function sequence, establish call for phone call in hands-free mode
^ Function sequence, terminate call via mobile phone buttons
^ Function sequence, terminate call via telephone buttons or keypad on COMAND operating, display and controller unit
^ Function sequence, terminate call via multifunction steering wheel button groups
^ Function sequence, call termination

The system is described using a mobile phone connected to the cell phone separation point and to the mobile phone adapter cable as an example. Deviations from this are indicated with the symbol.

Operating instruction
A telephone call can be established or terminated using the:
- Buttons on the mobile phone
- Telephone buttons or keypad on COMAND operating, display and controller unit
- Multifunction steering wheel button group
- VCS [SBS] (only for establishing call)

Function sequence, establish call via mobile phone buttons
Dialing the telephone number using the buttons on the mobile phone or selecting the telephone number from the mobile phone's telephone book and pressing the "Accept call button" initiates the telephone call in hands-free mode.

The control signals from the mobile phone buttons are internally processed and forwarded to the COMAND operating, display and controller unit via the following route:
- Adapter cable
- Cell phone separation point
- Direct line
- Communication control unit
- Direct line

With a mobile phone operating with Bluetooth, the control signals from the buttons on the mobile phone are processed internally. They are not forwarded to the COMAND operating, display and controller unit. The telephone call is completed in the "Private mode" when the mobile phone supports the "Private mode" and "Private mode" is activated.

Function sequence, establish call via telephone buttons or keypad on COMAND operating, display and controller unit
After dialing the telephone number via the telephone buttons on the COMAND operating, display and controller unit and pressing the "Accept phone call" button or by selecting the telephone function via the keypad on the COMAND operating, display and controller unit and then activating the "TRANSMIT" function, the telephone call is completed in hands-free mode. The telephone function can be selected with the menu item "ComTEL/Telephone"; this can be accomplished with the aid of the "TEL" telephone button on the COMAND operating, display and controller unit and is then indicated on the display of the COMAND operating, display and controller unit.

The following ways of dialing a telephone number are available to the user here:
- Enter telephone number with keypad on COMAND operating, display and controller unit with the speller offered
- Search for the telephone number using the "Name" menu entry in the address book
- Search for the telephone number using the "Call lists" menu entry in the call lists (accepted, dialed)

The name of the person who you wish to call can be selected in the address book and the call lists by scrolling up and down. The control signals from the telephone buttons or the keypad on the COMAND operating, display and controller unit are processed internally. The menu item is also indicated internally on the display of the COMAND operating, display and controller unit.

Function sequence, establish call via multifunction steering wheel button groups
The address book in the COMAND operating, display and controller unit or the telephone book in the mobile phone can be selected with the system selection (S110s3) button via the selection menu in the instrument cluster (A1).
The name of the person to be called can be selected by scrolling forward and backward in the COMAND operating, display and controller unit address book or in the telephone book in the telephone book of the mobile phone using the forward- and back (S110s1) buttons.
The accept/terminate phone call button (S111s3) can be used to establish the telephone call in the hands-free system.

The control signals from the multifunction steering wheel button groups are forwarded to the COMAND operating, display and controller unit via the following components:
- Direct line
- Steering column tube module (N80)
- Interior CAN

Display in the instrument cluster is accomplished by the COMAND operating, display and controller unit via the interior CAN.

Function sequence, establish call via voice control system
The voice control of the VCS [SBS] is activated by pressing the VCS [SBS] switch (S93/2) on the steering column tube module. The control signal of the VCS [SBS] switch is forwarded to the COMAND operating, display and controller unit via the following components:
- Direct line
- Steering column tube module
- Interior CAN

A signal tone is emitted after the voice control system has been activated.
The signal tone is transmitted by the COMAND operating, display and controller unit for vehicles with code (810) Sound System via the Media Oriented System Transport (MOST) to the Sound System amplifier (N40/3).

From there, the signal tone is transmitted via direct lines to the following speakers:
- Left door speaker group (H4/1)
- Right door speaker group (H4/2)
- Left rear speaker (H4/7)
- Right rear speaker (H4/8)
- Center cockpit speaker (centerfill) (H4/27)
- Subwoofer speaker (H4/29)

The audio signal for the subwoofer speaker is routed by the sound system amplifier via discrete lines to the subwoofer amplifier (N40/9) and from there, via discrete lines to the subwoofer speaker.

Now different voice commands can be used to search and select a telephone number.
The voice commands are received by the hands-free system microphone (B25) and transferred to the COMAND operating, display and controller unit via a direct line.
The voice control of the voice control system (VCS) is used to establish the telephone call in hands-free mode.

The individual voice commands are listed in the "Linguatronic operator's manual".

On vehicles except code (810) Sound system, the signal tone is transmitted from the COMAND operating, display and controller unit to the following speakers via direct lines:
- Left door speaker group
- Right door speaker group
- Left rear speaker
- Right rear speaker

Function sequence, establish call via navigation mode
If a telephone number is stored for a point of interest (POI), the user can dial it using the keypad on the COMAND operating, display and controller unit or by voice control on the VCS [SBS]. The telephone call is then established in hands-free mode. The control signals from the keypad on the COMAND operating, display and controller unit are processed internally.
The VCS [SBS] signals are forwarded to the COMAND operating, display and controller unit via the same route as for "Function sequence, establish telephone call via VCS [SBS]".

Function sequence, establish call for phone call in hands-free mode
After the telephone call is established, the COMAND operating, display and controller unit transmits and receives the mobile phone signals and data via the following route:
- Direct line
- Communication control unit
- Direct line
- Cell phone separation point
- Direct line
- Telephone antenna (A2/22)

The voice input in hands-free mode is received by the hands-free system microphone and transferred to the COMAND operating, display and controller unit via a direct line.

On vehicles with code (810) Sound system, the voice output is transferred from the COMAND operating, display and controller unit, via direct lines, to the following speakers:
- Left door speaker group
- Right door speaker group
- Left rear speaker
- Right rear speaker
- Center cockpit speaker (centerfill)
- Subwoofer speaker

The audio signal for the subwoofer speaker is routed by the sound system amplifier via direct lines to the subwoofer amplifier and from there, via direct lines to the subwoofer speaker.

On vehicles except code (810) Sound system, the voice output is transmitted from the COMAND operating, display and controller unit, via direct lines, to the following speakers:
- Left door speaker group
- Right door speaker group
- Left rear speaker
- Right rear speaker

With a mobile phone operated with Bluetooth, the COMAND operating, display and controller unit transmits or receives the mobile phone signals or data via the Bluetooth antenna (A2/91) and the mobile phone antenna, except when the telephone call is established using the mobile phone buttons. In the event of establishing a telephone call using the mobile phone buttons, the mobile phone transmits or receives the mobile phone signals or data via the mobile phone antenna. Voice input takes place using the microphone integrated in the mobile phone and voice output is emitted via the speakers integrated into the mobile phone ("private mode").

In the "Private mode" the user can make a call without other passengers in the vehicle being able to participate in the conversation when the mobile phone supports the "Private mode" and the "Private mode" is activated.

Function sequence, terminate call via mobile phone buttons
Pressing the "QUIT" button on the mobile phone terminates the telephone call. The control signals from the mobile phone buttons are internally processed and forwarded to the COMAND operating, display and controller unit via the following route:
- Adapter cable
- Cell phone separation point
- Direct line
- Communication control unit
- Direct line

With a mobile phone operating with Bluetooth, the control signals from the buttons on the mobile phone are processed internally. They are not forwarded to the COMAND operating, display and controller unit.

Function sequence, terminate call via telephone buttons or keypad on COMAND operating, display and controller unit
The telephone call can be terminated by pressing the "QUIT" button on the COMAND operating, display and controller unit or activating the "QUIT" function in the "ComTEL/Telephone" menu item. The control signals from the telephone buttons or the keypad on the COMAND operating, display and controller unit are processed internally.

Function sequence, terminate call via multifunction steering wheel button groups
The accept/terminate phone call button terminates the telephone call. The control signals from the multifunction steering wheel button groups are forwarded to the COMAND operating, display and controller unit via the following components:
- Direct line
- Steering column tube module
- Interior CAN

Function sequence, call termination
After completing a telephone call, the COMAND operating, display and controller unit discontinues transmission or reception of the mobile phone signals and data. This is accomplished internally in the COMAND operating, display and controller unit.

With a mobile phone operated with Bluetooth, the COMAND operating, display and controller unit discontinues transmission or reception of the mobile phone signals and data in an internal control unit procedure except when a call is terminated using the buttons on the mobile phone. When a telephone call is terminated using the mobile phone buttons, the mobile phone interrupts the transmission or reception of mobile phone signals or data. This process runs internally in the mobile phone.