Operation CHARM: Car repair manuals for everyone.
Home >> Mercedes Benz >> 2009 >> SL 65 AMG (230.479) V12-6.0L Turbo (275.981) >> Repair and Diagnosis >> A L L Diagnostic Trouble Codes ( DTC ) >> Testing and Inspection >> P Code Charts >> P0600 >> No CAN message from instrument cluster or message faulty. (P0600) >> Part 3

Part 3


No CAN message from instrument cluster or message faulty. (P0600)


1.1.2.2.9. AIRmatic

Test 1.1.2.2.9.1: Test voltage of terminal 30 at control unit N51 (AIRmatic with ADS control module).

Test 1.1.2.2.9.2: Test of cable for voltage supply

Test 1.1.2.2.9.3: Test procedure ground cable

1.1.2.2.9.1. Test voltage of terminal 30 at control unit N51 (AIRmatic with ADS control module).
Test prerequisite

- Battery voltage is OK.
Status of the relevant actual values:
- Terminal 30:Warning! Communication with ECU required.
Test sequence

- Switch off ignition.
- Connect socket box.
- Switch on ignition.

- Measure direct voltage with multimeter between sockets (2.21) 55 and (2.47) 81 of the 126-pole socket box tester.
Specified value

- [11...14 V]
Question

- Is the measurement value OK?


YES
The measurement value is OK.Note

- In the event of stored faults with a high fault frequency count or in the event of customer complaints, check lines and connectors for loose contact and corrosion..
End of test

NO
The actual value is not o.k.Note

- This test did not produce any clear result.
- Select further tests.


1.1.2.2.9.2. Test of cable for voltage supply
Test prerequisite

- Battery voltage is OK.
Test sequence

- Switch off ignition.
- Connect socket box.
- Switch on ignition.

- Measure direct voltage with multimeter between ground and socket (2.47) 81 of the 126-pole socket box tester.
Specified value

- [11...14 V]
Question

- Is the measurement value OK?


YES
The measurement value is OK.Note

- In the event of stored faults with a high fault frequency count or in the event of customer complaints, check lines and connectors for loose contact and corrosion..
End of test

NO
The measurement value is not OK.Possible cause and remedy

- Lines to component N51 (AIRmatic with ADS control module)
- F34f37 (Fuse 37)
End of test

1.1.2.2.9.3. Test procedure ground cable
Test prerequisite

- Battery voltage is OK.
Test sequence

- Switch off ignition.
- Connect socket box.

- W15/Measure resistance with multimeter between 1 and (2.21) 55 of the 35-pole socket box tester.
Specified value

- [<1ohms ]
Question

- Is the measurement value OK?


YES
The measurement value is OK.Note

- In the event of stored faults with a high fault frequency count or in the event of customer complaints, check lines and connectors for loose contact and corrosion..
End of test

NO
The measurement value is not OK.Possible cause and remedy

- Ground cable
- W15/1 (Ground (right footwell))
End of test

1.1.2.2.10. SBC

Test 1.1.2.2.10.1: Check power supply of component Left SBC.

Test 1.1.2.2.10.2: Check power supply of component Right SBC.

1.1.2.2.10.1. Check power supply of component Left SBC.

Test 1.1.2.2.10.1.1: Test voltage of terminal 87 at control unit A7/3 (SBC left hydraulic unit).

Test 1.1.2.2.10.1.2: Test of cable for voltage supply

Test 1.1.2.2.10.1.3: Test procedure ground cable

1.1.2.2.10.1.1. Test voltage of terminal 87 at control unit A7/3 (SBC left hydraulic unit).
Test prerequisite

- Battery voltage is OK.
Test sequence

- Switch off ignition.
- Connect socket box.
- Switch on ignition.

- Measure direct voltage with multimeter between sockets (1.44) 44 and (1.42) 42 of the 126-pole socket box tester.
Specified value

- [11...14 V]
Question

- Is the measurement value OK?


YES
The measurement value is OK.Note

- In the event of stored faults with a high fault frequency count or in the event of customer complaints, check lines and connectors for loose contact and corrosion..
End of test

NO
The measurement value is not OK.Possible cause and remedy

- Lines to component A7/3n1 (SBC left control module)
- N10/1f47 (Fuse 47)
End of test

1.1.2.2.10.1.2. Test of cable for voltage supply
Test prerequisite

- Battery voltage is OK.
Test sequence

- Switch off ignition.
- Connect socket box.
- Switch on ignition.

- Measure direct voltage with multimeter between ground and socket (1.42) 42 of the 126-pole socket box tester.
Specified value

- [11...14 V]
Question

- Is the measurement value OK?


YES
The measurement value is OK.Note

- In the event of stored faults with a high fault frequency count or in the event of customer complaints, check lines and connectors for loose contact and corrosion..
End of test

NO
The measurement value is not OK.Possible cause and remedy

- Lines to component A7/3 (SBC left hydraulic unit)
- N10/1f47 (Fuse 47)
End of test

1.1.2.2.10.1.3. Test procedure ground cable
Test prerequisite

- Battery voltage is OK.
Test sequence

- Switch off ignition.
- Connect socket box.

- W14/Measure resistance with multimeter between 2 and (1.44) 44 of the 35-pole socket box tester.
Specified value

- [<1ohms ]
Question

- Is the measurement value OK?


YES
The measurement value is OK.Note

- In the event of stored faults with a high fault frequency count or in the event of customer complaints, check lines and connectors for loose contact and corrosion..
End of test

NO
The measurement value is not OK.Possible cause and remedy

- Ground cable
- W14/2 (Left SBC ground)
End of test

1.1.2.2.10.2. Check power supply of component Right SBC.

Test 1.1.2.2.10.2.1: Test voltage of terminal 87 at control unit A7/4n1 (SBC right control module).

Test 1.1.2.2.10.2.2: Test of cable for voltage supply

Test 1.1.2.2.10.2.3: Test procedure ground cable

1.1.2.2.10.2.1. Test voltage of terminal 87 at control unit A7/4n1 (SBC right control module).
Test prerequisite

- Battery voltage is OK.
Test sequence

- Switch off ignition.
- Connect socket box.
- Switch on ignition.

- Measure direct voltage with multimeter between sockets (1.44) 44 and (1.42) 42 of the 126-pole socket box tester.
Specified value

- [11...14 V]
Question

- Is the measurement value OK?


YES
The measurement value is OK.Note

- In the event of stored faults with a high fault frequency count or in the event of customer complaints, check lines and connectors for loose contact and corrosion..
End of test

NO
The measurement value is not OK.Possible cause and remedy

- Lines to component A7/4n1 (SBC right control module)
- N10/1f47 (Fuse 47)
End of test

1.1.2.2.10.2.2. Test of cable for voltage supply
Test prerequisite

- Battery voltage is OK.
Test sequence

- Switch off ignition.
- Connect socket box.
- Switch on ignition.

- Measure direct voltage with multimeter between ground and socket (1.42) 42 of the 126-pole socket box tester.
Specified value

- [11...14 V]
Question

- Is the measurement value OK?


YES
The measurement value is OK.Note

- In the event of stored faults with a high fault frequency count or in the event of customer complaints, check lines and connectors for loose contact and corrosion..
End of test

NO
The measurement value is not OK.Possible cause and remedy

- Lines to component A7/4n1 (SBC right control module)
- N10/1f47 (Fuse 47)
End of test

1.1.2.2.10.2.3. Test procedure ground cable
Test prerequisite

- Battery voltage is OK.
Test sequence

- Switch off ignition.
- Connect socket box.

- W14/Measure resistance with multimeter between 2 and (1.44) 44 of the 35-pole socket box tester.
Specified value

- [<1ohms ]
Question

- Is the measurement value OK?


YES
The measurement value is OK.Note

- In the event of stored faults with a high fault frequency count or in the event of customer complaints, check lines and connectors for loose contact and corrosion..
End of test

NO
The measurement value is not OK.Possible cause and remedy

- Ground cable
- W14/2 (Left SBC ground)
End of test

1.1.2.2.11. SGR - Radar sensors control unit
Test voltage supply of circuit 87.
Test prerequisite

- Battery voltage is OK.
- Fuse N10/1f46 (Fuse 46) in component N10/1 (Driver-side SAM control unit with fuse and relay module) is o.k.
Status of relevant actual value:
- Voltage supply terminal 15:Warning! Communication with ECU required.
Test sequence

- Switch off ignition.
- Separate plug connection A at control unit N62/1 (Radar sensors control unit (SGR)).
- Measure direct voltage with multimeter between sockets (N62/1) A.16 and (N62/1) A.1
Specified value

- Voltage[11.0 ... 14.5] V
Question

- Is the measurement value OK?







YES
Test voltage supply of circuit 87.
Test prerequisite

- Fuse N10/1f46 (Fuse 46) in component N10/1 (Driver-side SAM control unit with fuse and relay module) is o.k.
Status of relevant actual value:
- Voltage supply terminal 15:Warning! Communication with ECU required.
Test sequence

- Switch on ignition.
- Measure direct voltage with multimeter between sockets (N62/1) A.16 and (N62/1) A.5
Specified value

- Voltage[11.0 ... 14.5] V
Question

- Is the measurement value OK?







YES
The measurement value is OK.Possible cause and remedy

- In the event of stored faults with a high fault frequency count or in the event of customer complaints, check lines and connectors for loose contact and corrosion..
End of test

NO
The measurement value is not OK.Possible cause and remedy

- Check line from N62/1 (Radar sensors control unit (SGR)) to N10/1 (Driver-side SAM control unit with fuse and relay module) for Short circuit or open circuit.
- Check line from N62/1 (Radar sensors control unit (SGR)) to W15/2 (Ground, left footwell) for Open circuit.
- Check control unit N10/1 (Driver-side SAM control unit with fuse and relay module).
End of test







NO
The measurement value is not OK.Possible cause and remedy

- Check line from N62/1 (Radar sensors control unit (SGR)) to N10/1 (Driver-side SAM control unit with fuse and relay module) for Short circuit or open circuit.
- Check line from N62/1 (Radar sensors control unit (SGR)) to W15/2 (Ground, left footwell) for Open circuit.
- Check control unit N10/1 (Driver-side SAM control unit with fuse and relay module).
End of test







1.1.2.2.12. TPC - Tire pressure monitor
Operation number of operation texts and work units or standard texts and flat rates:40-0641Test prerequisite

- Battery voltage is OK.
Test sequence

- Switch off ignition.
- Disconnect connector at component N88 (TPM [RDK] control unit).
- [A.16] Measure direct voltage with multimeter between 16 and 15 [A.15]
Specified value

- Voltage[11.0...14.5] V
Question

- Is the measurement value OK?


YES
The measurement value is OK.Possible cause and remedy

- Inspect cables, electrical connections and plug connections for damage, correct connection, loose contact and corrosion, and repair or replace if necessary.
- Replace component N88 (TPM [RDK] control unit).
End of test

NO
The measurement value is not OK.Possible cause and remedy

- Check fuse f2 (voltage supply from control unit N88 (TPM [RDK] control unit)) in component N10/3 (SAM control module with fuse and relay module rear-end 1).
- Check lines from component N88 (TPM [RDK] control unit) to component N10/3 (SAM control module with fuse and relay module rear-end 1).
End of test

1.1.2.2.13. N118 (Fuel pump control module)

Test 1.1.2.2.13.1: Check power supply at control unit N118 (Fuel pump control module).

1.1.2.2.13.1. Check power supply at control unit N118 (Fuel pump control module).
Possible cause and remedy

- Test fuse, replace if necessary
-
Question

- Is fuse OK?


YES
Test prerequisite

- If other control units also report low-voltage faults, check alternator and governor, repair or replace as necessary.
-
Test sequence

- Switch on ignition.
- Unplug 4-pin connector from component N118 (Fuel pump control module).
- Measure voltage at the unclipped cable.(Ground- Positive)
- Measure direct voltage with multimeter between sockets (N118) 1.2 and (N118) 1.1
Specified values

- Voltage: [11.0 ... 14.5] V
Question

- Is the measurement value OK?







YES
The measurement value is OK.Further possible causes of fault

- Inspect plug connections for corrosion, pinched insulation and loose contact.
End of test

NO
The measurement value is not OK.Possible cause and remedy

- Inspect lead of voltage supply to control module N118 (Fuel pump control module) if necessary for loose contact, damage and corrosion and repair.
End of test

NO
Replace faulty fuse.End of test

1.1.2.2.14. HRA - Headlamp range adjustment
Warning!Communication with ECU required.


1.1.2.3. Resistance test of engine compartment CAN

Test 1.1.2.3.1: Test terminating resistor of component X30/5 (Left voltage distributor (CAN) connector).

Test 1.1.2.3.2: Test terminating resistor of CAN element in control module ME-SFI 2.7.1.

Test 1.1.2.3.3: Test total resistance of engine compartment CAN.

1.1.2.3.1. Test terminating resistor of component X30/5 (Left voltage distributor (CAN) connector).
Test terminating resistor of component X30/5 (Left voltage distributor (CAN) connector).
Test sequence

- Switch off ignition.
- Connect socket box to component N3/10 (ME-SFI [ME] control unit).
- Disconnect coupling 4 at component N3/10 (ME-SFI [ME] control unit).
- Measure resistance with multimeter between sockets (4.11) 96 and (4.1) 86 of the 126-pole socket box tester.
Specified value

- Resistor[115...125]ohms
Question

- Is the measurement value OK?


YES
The measurement value is OK.Further possible causes of fault

- Fault in control unit EZS: Read out fault memory of control unit N73 (EIS [EZS] control unit).
- Read out fault memory of control unit N93 (Central gateway control unit).
End of test

NO
The measurement value is not OK.Possible cause and remedy

- Line from component X30/5 (Left voltage distributor (CAN) connector) to component N3/10 (ME-SFI [ME] control unit)
- Component X30/5 (Left voltage distributor (CAN) connector)
End of test

1.1.2.3.2. Test terminating resistor of CAN element in control module ME-SFI 2.7.1.
Test terminating resistor of component ME-SFI 2.8.
Test sequence

- Switch off ignition.
- Connect socket box to component N3/10 (ME-SFI [ME] control unit).
- Connector 4 is plugged in at control unit.
- Unplug the socket 4 from the wiring harness at the socket box.
- Measure resistance with multimeter between sockets (4.11) 96 and (4.1) 86 of the 126-pole socket box tester.
Specified value

- Resistor[115...125]ohms
Question

- Is the measurement value OK?


YES
The measurement value is OK.End of test

NO
The measurement value is not OK.Possible cause and remedy

- Control unit N3/10 (ME-SFI [ME] control unit)
End of test

1.1.2.3.3. Test total resistance of engine compartment CAN.
Test total resistance of the CAN engine.
Test sequence

- Switch off ignition.
- Connect socket box to component N3/10 (ME-SFI [ME] control unit).
- Measure resistance with multimeter between sockets (4.11) 96 and (4.1) 86 of the 126-pole socket box tester.
Specified value

- Resistor[55...65]ohms
Question

- Is the measurement value OK?


YES
The measurement value is OK.Further possible causes of fault

- Fault in control unit EZS: Read out fault memory of control unit N73 (EIS [EZS] control unit).
End of test

NO
The measurement value is not OK.Possible cause and remedy

- Line from component N3/10 (ME-SFI [ME] control unit) to component X30/5 (Left voltage distributor (CAN) connector)
- Test terminating resistor of component X30/5 (Left voltage distributor (CAN) connector).
- Test terminating resistor of CAN element in control module N3/10 (ME-SFI [ME] control unit).


pro multis · About Operation CHARM