AZ82.80-P-0002-01EC Retrofit InCar Hotspot Wiring Harness
AZ82.80-P-0002-01EC Retrofit InCar Hotspot Wiring Harness
000 589 13 99 00, Wiring harness repair kit, basic
220 589 04 99 00, New passenger vehicle wiring harness repair kit
Connection scheme
1 InCar Hotspot
2 Cellular telephone system splitter
3 Cellular telephone system splitter/InCar Hotspot antenna line
4 Cellular telephone system splitter/vehicle antenna line
6 Power supply wiring harness
7 Vehicle/cellular telephone system splitter antenna line
17 Black 2-pin connector
A28/11x1 Multifunction antenna electrical connector
N10/2 Rear SAM control unit with fuse and relay module
W7 Right wheelhouse trunk ground point
br Brown line
rt Red line
sw Black wire
Routing diagram
1 InCar Hotspot
2 Cellular telephone system splitter
3 Cellular telephone system splitter/InCar Hotspot antenna line
4 Cellular telephone system splitter/ vehicle antenna line
6 Power supply wiring harness
7 Vehicle/cellular telephone system splitter antenna line
A28/11x1 Multifunction antenna electrical connector
N10/2 Rear SAM control unit with fuse and relay module
W7 Right wheelhouse trunk ground point
1 Remove multifunction antenna electrical connector (A28/11x1) from bracket (12) and disconnect.
The color of the multifunction antenna electrical connector (A28/11x1) is black.
2 Wrap felt tape around cellular telephone system splitter (2)
3 Place cellular telephone system splitter (2) in vehicle in vicinity of multifunction antenna electrical connector (A28/11x1).
4 Connect disconnected connector of multifunction antenna electrical connector (A28/11x1) to black 1-pin connector (7.1) of the vehicle/cellular telephone system splitter antenna line (7).
5 Connect disconnected connector of multifunction antenna electrical connector (A28/11x1) to the black 1-pin connector (4.1) of the cellular telephone system splitter/vehicle antenna line (4).
6 Connect black 1-pin connector of cellular telephone system splitter/InCar Hotspot antenna line (3) to the cellular telephone system splitter (2) and route to breakthrough below rear shelf.
7 Fasten cellular telephone system splitter (2) to vehicle wiring harness using felt tape, and route antenna line for cellular telephone system splitter/InCar Hotspot (3) through breakthrough to the rear shelf.
8 Route cellular telephone system splitter/InCar Hotspot antenna line (3) along rear shelf to InCar Hotspot (1).
9 Connect cellular telephone system splitter/InCar Hotspot antenna line (3) to InCar Hotspot (1).
10 Connect power supply wiring harness (6) to InCar Hotspot (1) and route along existing lines to rear SAM control unit with fuse and relay module (N10/2).
11 Secure power supply wiring harness (6) and cellular telephone system splitter/InCar Hotspot antenna line in vicinity of rear shelf with several strips of felt tape.
12 Secure power supply wiring harness (6) with cable ties.
13 Route brown line (br) of power supply wiring harness behind the rear SAM control unit with fuse and relay module (N10/2) to the right wheel arch trunk ground point (W7) and connect.
14 Check whether a fuse has been installed in slot (arrow A) of rear SAM control unit with fuse and relay module (N10/2).
If a fuse has been inserted into slot (arrow A), perform the following operation steps at one of the slots (arrows B, C or D) accordingly.
15 Detach yellow fuse carrier (15) from rear SAM control unit with fuse and relay module and open lock (15.1).
16 Open lock (15.3) of yellow fuse carrier (15).
17 Pin black line (sw) of power supply wiring harness into second contact cavity (15.2) of yellow fuse carrier (15).
18 Close lock (15.3) of yellow fuse carrier (15).
19 Insert fuse (16) into yellow fuse carrier (15) and close lock (15.1).
The fuse rating is 7,5 A.
20 Attach yellow fuse carrier (15) to rear SAM control unit with fuse and relay module.
21 Check whether the slot (arrow E) has been installed at the rear SAM control unit with fuse and relay module (N10/2) and whether a fuse has been inserted.
The slot (arrow E) on the rear of the rear SAM control unit with fuse and relay module (N10/2) is marked with "10R". If a fuse has been inserted in the slot (arrow E) or the slot (arrow E) is not present, continue with operation step 27.
22 Open lock (17.1) of black coupling housing (17).
The black coupling housing (17) is included in the installation kit.
23 Pin red line (rt) of power supply wiring harness into contact cavity 2 of the black coupling housing (17).
Contact cavity 2 of the black coupling housing (17) is marked.
24 Close lock (17.1) of black coupling housing (17).
25 Plug black connector (17) into slot "10R" on rear of rear SAM control unit with fuse and relay module (N10/2).
26 Insert a fuse with a fuse rating of 7.5 A into slot (arrow E).
Only perform the following operation steps if the slot (arrow E) at the rear SAM control unit with fuse and relay module (N10/2) was occupied or if it was not present.
27 Select a free slot (arrows F, G, H and K).
28 Detach fuse carrier (20) from rear SAM control unit with fuse and relay module.
29 Open lock (20.1) of fuse carrier (20).
30 Disconnect SLK contact (18) of red line (rt) of power supply wiring harness.
31 Crimp an SLK 2.8 contact (19) to the red line (rt) of the power supply wiring harness.
32 Open lock (20.3) of fuse carrier (20).
33 Pin red line (rt) of power supply wiring harness into second contact cavity (20.2) of fuse carrier (20).
34 Close lock (20.3) of fuse carrier (20).
35 Insert fuse (21) into fuse carrier (20) and close lock (20.1).
The fuse rating is 7,5 A.
36 Attach fuse carrier (20) to rear SAM control unit with fuse and relay module.