Part 2
45. CAUTION: Do not use metal scrapers, wire brushes, power abrasive discs or other abrasive means to clean the sealing surfaces. These tools cause scratches and gouges which make leak paths.
Clean the intake manifold sealing surfaces.
46. Remove the bolts and the RH engine mount.
47. NOTE: LH shown, RH similar.
Remove the cylinder block drain plugs. Reinstall the drain plugs after draining the coolant.
48. CAUTION: Do not use metal scrapers, wire brushes, power abrasive discs or other abrasive means to clean the sealing surfaces. These tools cause scratches and gouges which make leak paths.
NOTE: There are several kinds of bolts used in fastening the valve cover. The bolts must be installed in their original locations.
Remove the LH valve cover.
Clean and inspect the mating surfaces, and if necessary install new gaskets.
49. CAUTION: Do not use metal scrapers, wire brushes, power abrasive discs or other abrasive means to clean the sealing surfaces. These tools cause scratches and gouges which make leak paths.
NOTE: There are several kinds of bolts used in fastening the valve cover. The bolts must be installed in their original locations.
Remove the RH valve cover.
Clean and inspect the mating surfaces, and if necessary install new gaskets.
50. NOTE: Use compressed air to remove any foreign material from the spark plug wells before removing the spark plugs.
Remove the spark plugs.
51. Remove the crankshaft pulley bolt. Using the special tool, remove the crankshaft pulley.
52. Using the special tool, remove the crankshaft front oil seal.
53. Remove the four oil pan bolts.
54. CAUTION: Do not use metal scrapers, wire brushes, power abrasive discs or other abrasive means to clean the sealing surfaces. These tools cause scratches and gouges which make leak paths.
Remove the studs, bolts and the engine front cover.
55. Remove the front cover gaskets, clean and inspect the front cover sealing surfaces.
56. Remove the crankshaft sensor ring from the crankshaft.
57. Install the special tool between the valve spring coils to prevent valve stem seal damage.
58. NOTE: Mark the followers for installation in their original locations.
NOTE: Position the cam lobe away from the camshaft roller follower prior compressing the valve spring.
Using the special tool to compress the valve spring, remove the camshaft roller followers.
59. Remove the special tool.
60. Position the crankshaft with the keyway at the 12 o'clock position.
61. Remove the timing chain tensioning system from both timing chains.
1. Remove the bolts.
2. Remove the timing chain tensioners.
3. Remove the timing chain tensioner arms.
62. Remove the LH and the RH timing chains and the crankshaft sprocket.
63. Remove both timing chain guides.
64. Install the Lifting Handles on both ends of the cylinder head.
65. NOTE: The hydraulic lash adjusters must be installed in their original locations. Record hydraulic lash adjuster locations.
Remove the hydraulic lash adjuster.
RH Cylinder Head
66. Remove the nut and the tube.
67. CAUTION: The cylinder head must be cool before removing it from the engine. Cylinder head warpage can result if a warm or hot cylinder head is removed.
CAUTION: Place clean shop towels over exposed engine cavities. Carefully remove the towels so foreign material is not dropped into the engine.
CAUTION: The cylinder head bolts must be discarded and new bolts installed. They are torque-to-yield designed and cannot be reused.
CAUTION: Do not use metal scrapers, wire brushes, power abrasive discs or other abrasive means to clean the sealing surfaces. These tools cause scratches and gouges that make leak paths. Use a plastic scraping tool to remove all traces of the head gasket.
CAUTION: Aluminum surfaces are soft and can be scratched easily. Never place the cylinder head gasket surface, unprotected, on a bench surface.
Remove the bolts and the RH cylinder head.
- Discard the cylinder head gasket.
- Discard the cylinder head bolts.
LH Cylinder Head
68. CAUTION: The cylinder head must be cool before removing it from the engine. Cylinder head warpage can result if a warm or hot cylinder head is removed.
CAUTION: Place clean shop towels over exposed engine cavities. Carefully remove the towels so foreign material is not dropped into the engine.
CAUTION: The cylinder head bolts must be discarded and new bolts installed. They are torque-to-yield designed and cannot be reused.
CAUTION: Do not use metal scrapers, wire brushes, power abrasive discs or other abrasive means to clean the sealing surfaces. These tools cause scratches and gouges that make leak paths. Use a plastic scraping tool to remove all traces of the head gasket.
CAUTION: Aluminum surfaces are soft and can be scratched easily. Never place the cylinder head gasket surface, unprotected, on a bench surface.
Remove the bolts and the LH cylinder head.
- Discard the cylinder head gasket. Discard the cylinder head bolts.
Both Cylinder Heads
CAUTION: Do not use metal scrapers, wire brushes, power abrasive discs or other abrasive means to clean the sealing surfaces. These tools cause scratches and gouges that make leak paths. Use a plastic scraping tool to remove all traces of the head gasket.
CAUTION: Observe all warnings or cautions and follow all application directions contained on the packaging of the silicone gasket remover and the metal surface prep.
NOTE: If there is no residual gasket material present, metal surface prep can be used to clean and prepare the surfaces.
69. Clean the cylinder head-to-cylinder block mating surfaces of both the cylinder head and the cylinder block.
1. Remove any large deposits of silicone or gasket material with a plastic scraper.
2. Apply silicone gasket remover, following package directions, and allow to set for several minutes.
3. Remove the silicone gasket remover with a plastic scraper. A second application of silicone gasket remover may be required if residual traces of silicone or gasket material remain.
4. Apply metal surface prep, following package directions, to remove any remaining traces of oil or coolant, and to prepare the surfaces to bond with the new gasket. Do not attempt to make the metal shiny. Some staining of the metal surfaces is normal.
70. NOTE: The straightedge used must be flat within 0.0051 mm (0.0002 in) per foot of tool length.
Support the cylinder head on a bench with the head gasket side up. Inspect all areas of the deck face with a straightedge, paying particular attention to the oil pressure feed area. The cylinder head must not have depressions deeper than 0.00254 mm (0.001 in) across a 38.1 mm (1.5 in) square area, or scratches more than 0.0254 mm (0.001 in).