Deactivation

Special Tool(s):

Deactivation


WARNING: Always wear safety glasses when repairing an air bag supplemental restraint system (SRS) vehicle and when handling an air bag module. This will reduce the risk of injury in the event of an accidental deployment.

WARNING: Carry a live air bag module with the air bag and trim cover pointed away from your body. This will reduce the risk of injury in the event of an accidental deployment.

WARNING: Do not set a live air bag module down with the trim cover face down. This will reduce the risk of injury in the event of an accidental deployment.

WARNING: After deployment, the air bag surface can contain deposits of sodium hydroxide, a product of the gas generant combustion that is irritating to the skin. Wash your hands with soap and water afterwards.

WARNING: Never probe the connectors on the air bag module. Doing so can result in air bag deployment, which can result in personal injury.

WARNING: The safety belt pretensioner is a pyrotechnic device. Always wear safety glasses when repairing an air bag equipped vehicle and when handling a safety belt buckle pretensioner or safety belt retractor pretensioner. Never probe a pretensioner electrical connector. Doing so could result in pretensioner or air bag deployment and could result in personal injury.

WARNING: Never probe the connectors on the safety canopy module. Doing so can result in safety canopy deployment.

WARNING: Vehicle sensor orientation is critical for proper system operation. If a vehicle equipped with an air bag supplemental restraint system (SRS) is involved in a collision, inspect the sensor mounting bracket and wiring pigtail for deformation. Replace and properly position the sensor or any other damaged supplemental restraint system (SRS) components whether or not the air bag is deployed.

WARNING: The restraint system diagnostic tool is for restraint system service only. Remove from vehicle prior to road use. Failure to remove could result in injury and possible violation of vehicle safety standards.

NOTE: If a seat equipped with a seat mounted side air bag and/or a safety belt pretensioner (if equipped) system is being serviced, the air bag system must be deactivated.

NOTE: Restraint system diagnostic tools MUST be installed under the seats in the seat side air bag (if equipped) and safety belt pretensioner (if equipped) to floor connectors.

NOTE: Diagnostics or repairs are not to be performed on a seat equipped with a seat side air bag with the seat in the vehicle. Prior to attempting to diagnose or repair a seat concern when equipped with a seat side air bag the seat must be removed from the vehicle and the restraint system diagnostic tools must be installed in the seat side air bag electrical connectors. The restraint system diagnostic tools must be removed prior to operating the vehicle over the road.

NOTE: After diagnosing or repairing an SRS the restraint system diagnostic tools must be removed before operating the vehicle over the road.

NOTE: After diagnosing or repairing a seat system, the restraint system diagnostic tools must be removed before operating the vehicle over the road.

NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.

All Vehicles

1. WARNING: To avoid accidental deployment and possible personal injury, the backup power supply must be depleted before repairing or replacing any front or side air bag supplemental restraint system (SRS) components and before servicing, replacing, adjusting or striking components near the front or side air bag sensors, such as doors, instrument panel, console, door latches, strikers, seats and hood latches. The side impact sensors (if equipped) are located at or near the base of the B-pillars and C-pillars. To deplete the backup power supply energy, disconnect the battery ground cable and wait at least one minute. Be sure to disconnect auxiliary batteries and power supplies (if equipped).

Disconnect the battery ground cable and wait at least one minute.







2. Remove the two steering wheel back cover plugs (one shown).







3. Remove the two driver air bag module bolts (one shown).
4. Remove the driver air bag module.
1 Release the two retaining tabs. Disconnect the driver air bag module electrical connector.
- Label the driver air bag module squib number on the driver air bag module electrical connector before disconnecting.

2 Release the two retaining tabs. Disconnect the driver air bag module electrical connector.
- Label the driver air bag module squib number on the driver air bag module electrical connector before disconnecting.

3 Disconnect the horn switch electrical connector.







4 Remove the driver air bag module.







5. Attach the restraint system diagnostic tools to the clockspring electrical connectors at the top of the steering column.







6. Push in on the glove compartment sides, releasing the stops and lowering it out of the way.







7. Through the glove compartment opening, release the tab and disconnect the passenger air bag module electrical connector.







8. Attach the restraint system diagnostic tool to the vehicle harness side of the passenger air bag module electrical connector.



Vehicles Without Safety Canopies

9. CAUTION: Do not deactivate the safety canopy module circuit by removing the safety canopy bridge resistor from the safety canopy electrical connector.

If the safety canopy bridge resistor is removed an open circuit fault will be generated by the restraints control module (RCM).
If a restraint system diagnostic tool is installed at the safety canopy electrical connector, a low resistance fault will be generated by the RCM.


Vehicles With Safety Canopies

10. Remove the RH C-pillar trim panel.
l Pull out and release the retaining clips.
2 Pull out and release the retainer.







3 Lower the door opening weatherstrip, slide the C-pillar trim panel up, releasing the retainers and remove the C-pillar trim panel.







11. Disconnect the RH safety canopy electrical connector.







12. Attach the restraint system diagnostic tool to the vehicle harness side of the RH safety canopy electrical connector.


Vehicles With Power Seats

13. Connect the battery ground cable.


All Vehicles

14. Move and tilt the front seats to their highest and most forward position.

Vehicles With Power Seats

15. WARNING: To avoid accidental deployment and possible personal injury, the backup power supply must be depleted before repairing or replacing any front or side air bag supplemental restraint system (SRS) components and before servicing, replacing, adjusting or striking components near the front or side air bag sensors, such as doors, instrument panel, console, door latches, strikers, seats and hood latches. The side impact sensors (if equipped) are located at or near the base of the B-pillars and C-pillars. To deplete the backup power supply energy, disconnect the battery ground cable and wait at least one minute. Be sure to disconnect auxiliary batteries and power supplies (if equipped).

Disconnect the battery ground cable and wait at least one minute


All Vehicles







16. From under the front RH seat, push in to release the tab and disconnect the safety belt buckle pretensioner electrical connector.







17. Attach the restraint system diagnostic tool to the front RH seat safety belt buckle pretensioner floor electrical connector.


Vehicles With Safety Canopies

18. Remove the LH C-pillar trim panel.
1 Pull out and release the retaining clips.
2 Pull out and release the retainer.







3 Lower the door opening weatherstrip, slide the C-pillar trim panel up, releasing the retainers and remove the C-pillar trim panel.







19. Disconnect the LH safety canopy electrical connector.







20. Attach the restraint system diagnostic tool to the vehicle harness side of the LH safety canopy electrical connector.


All Vehicles







21. From under the front LH seat, push in to release the tab and disconnect the safety belt buckle pretensioner electrical connector.







22. Attach the restraint system diagnostic tool to the front LH seat safety belt buckle pretensioner floor electrical connector.
23. Connect the battery ground cable.
24. With the restraint system diagnostic tools installed at all deployable devices, prove out the supplemental restraint system (SRS).
25. Disconnect the battery ground cable and wait at least one minute.