Part 2 of 2

Engine continued





36. Remove the 2 bolts and the fuel rail with the fuel injectors.





37. Remove the fuel rail spacers.





38. Detach the wiring harness retainer.





39. Disconnect the EGR valve and radio interference capacitor electrical connectors. Detach the wiring harness retainer.





40. Disconnect the coil-on-plug and camshaft position (CMP) sensor electrical connectors.





41. Detach the wiring harness retainer.





42. Position the rubber boot aside and disconnect the cylinder head temperature (CHT) sensor electrical connector. Remove the wiring harness from the engine.





43. Disconnect the coolant hose.





44. Disconnect and remove the coolant hose.





45. Disconnect and remove the coolant hoses.





46. Remove the bolt and the KS.





47. Remove the bolts and the crankcase vent oil separator.





48. If equipped, remove the block heater.





49. Remove the crankcase vent tube and the coil-on-plugs.





50. Remove the spark plugs and the CHT sensor.
^ Discard the CHT.





51. Remove the bolts and the valve cover.

52. CAUTION: Failure to position the No. 1 piston at top dead center (TDC) can result in damage to the engine. Turn the engine in the normal direction of rotation only.

Using the crankshaft pulley bolt, turn the crankshaft clockwise to position the No. 1 piston at TDC.
^ The hole in the crankshaft pulley should be in the 6 o'clock position.





53. CAUTION: The special tool 303-465 is for camshaft alignment only. Using this tool to prevent engine rotation can result in engine damage.

NOTE: The camshaft timing slots are offset. If the special tool cannot be installed, rotate the crankshaft one complete revolution clockwise to correctly position the camshafts.

Install the special tool in the slots on the rear of both camshafts.





54. Remove the engine clue bolt.





55. NOTE: The special tool will contact the crankshaft and prevent it from Burning past TDC. However, the crankshaft can still be rotated in the counterclockwise direction.

Install the special tool.





56. Install the special tools.





57. CAUTION: Failure to hold the crankshaft pulley in place while loosening the bolt can result in damage to the engine.

Remove the crankshaft pulley.
^ Remove the crankshaft pulley bolt and washer. Discard the bolt.
^ Remove the crankshaft pulley.





58. CAUTION: Use care not to damage the engine front cover or the crankshaft when removing the seal.

Using the special tool, remove the crankshaft front oil seal.





59. NOTE: Whenever the CKP sensor is removed, a new one must be installed using the alignment jig supplied with the new part.

Remove and discard the CKP sensor.





60. Remove the bolts and the engine front cover.





61. Remove the timing chain tensioner.
1. Compress the timing chain tensioner, and insert a paper clip into the hole to retain the tensioner.
2. Remove the bolts and timing chain tensioner.





62. Remove the RH timing chain guide.





63. Remove the timing chain.





64. Remove the bolts and the LH timing chain guide.





65. CAUTION: Do not rely on the Camshaft Alignment Plate to prevent camshaft rotation. Damage to the tool or the camshaft can occur.

Using the flats on the camshaft to prevent camshaft rotation, remove the bolts and the camshaft sprockets.





66. Remove the oil pump chain tensioner and guide.
1. Release the tension on the tensioner spring.
2. Remove the tensioner and the shoulder bolt.
3. Remove the guide.





67. NOTE: Remove the crankshaft sprocket diamond washers located in front of and behind the crankshaft sprocket.

NOTE: The oil pump chain sprocket must be held in place.

Remove the oil pump chain and sprockets.
1. Remove the bolt.
2. Remove the chain and sprockets.





68. Mark the position of the camshaft lobes on the No. 1 cylinder for assembly reference.





69. CAUTION: Failure to follow the camshaft loosening procedure can result in damage to the camshafts.

Remove the camshafts from the engine.
^ Loosen the camshaft bearing bolts in the sequence shown, one turn at a time. Repeat until all the tension is released.
^ Remove the camshaft bearing caps.
^ Remove the camshafts.





70. Remove the cylinder head.
^ Remove and discard the cylinder head bolts.
^ Remove the cylinder head.
^ Remove and discard the cylinder head gasket.





71. Remove the cylinder head alignment dowels.





72. Remove the bolts and the oil pan.





73. Remove the bolts and the rear crankshaft seal.





74. Remove the bolts, oil pump pickup tube and gasket.





75. Remove the bolts and the oil pump.





76. If necessary, remove the bolts and halfshaft support bracket.