Steps 51-100

51. Loosely install the screw.





52. Install the intermediate band apply strut.





53. CAUTION: If the strut is installed incorrectly, transmission damage will occur.

Check to make sure that the intermediate band apply strut is installed in the correct orientation to the case and piston rod.





54. Install the selected No. 4 thrust washer on the direct clutch drum.
^ Coat the thrust washer with petroleum jelly.





55. NOTE: Align the center support screw hole with correct case hole.

Install the center support.





56. Install the center support locknut and cage.





57. Loosely install the screw.





58. CAUTION: Install the center support retaining ring with the tapered side facing up.

CAUTION: Make sure the notch opening is not obstructed by the center support retaining ring.

Install the center support retaining ring.
1 Make sure the center support retaining ring is installed with the tapered side facing up.
2 Make sure the opening of the center support retaining ring is positioned correctly.





59. Install the center shaft thrust bearing (No. 3).





60. Install the overdrive ring gear, overdrive one-way clutch and center shaft assembly.





61. CAUTION: Do not bend the trigger wheel. Make sure that the No. 2 thrust bearing is in this assembly.

Install the Planetary gear overdrive carrier.





62. Install the overdrive brake drum and coast clutch drum assembly.





63. Install the overdrive band servo piston and spring.
^ Lubricate the servo bore with clean automatic transmission fluid.





64. Using the special tools, install the retaining ring.





65. NOTE: If the overdrive band is reused, it must be installed in the same position as when removed.

NOTE: Make sure that the overdrive band apply strut is aligned with the band notch.

NOTE: The new overdrive band is dark in color. This is a normal condition of the band. Hairline cracks in the band are also considered normal. Do not install a new band based solely on the color.

Install the overdrive band.








66. CAUTION: To avoid a fall out condition of the strut from the screw during assembly and function, the small U-shaped notch should be toward the band and the large U-shaped notch toward the main control side.

Install the overdrive anchor strut.
1 Small "U" notch.
2 Large "U" notch.





67. CAUTION: If the strut is installed incorrectly, transmission damage will occur.

Check to make sure that the overdrive band anchor strut is installed in the correct orientation to the case and adjustment screw.





68. Loosely install the screw.





69. Install the overdrive apply strut.





70. CAUTION: If the strut is installed incorrectly, transmission damage will occur.

Check to make sure that the overdrive band apply strut is installed in the correct orientation to the case and piston rod.





71. CAUTION: The torque specifications are critical for this procedure. Failure to use the correct torque specifications may cause transmission damage.

Install the special tool.
1 Install the special tool and the bolts using the 2 pump screw locations at approximately 6 and 12 o'clock positions.
^ Tighten to 15 Nm (11 ft. lbs.).
2 Tighten the center screw.
^ Tighten to 1 Nm (10 inch lbs.).





72. NOTE: Align the disc holes on special tool with the slot in gauge bar for correct measurement.

Measure the distance from the top of the gauge bar to the drum bearing surface through the hole in the disc and record as dimension A. Repeat measurement 180 degrees opposite side of the special tool and record as dimension B.
73. Add dimension A to B. divide by 2 and record as dimension C.
74. Subtract the thickness of the gauge bar 17.78 mm (0.71 inch) from dimension C and record as dimension D.





75. Select the No. 1 thrust bearing from the above chart using dimension D.





76. Install the selected No. 1 fluid pump input thrust washer.
^ Coat the fluid pump input thrust washer with petroleum jelly.





77. Install the special tools into the transmission case.





78. Install the pump gasket.





79. CAUTION: Make sure that the fluid pump inlet thrust washer (No. 1), selective thrust washer, fluid pump gasket and the fluid pump-to-case O-ring seal remain in the correct position throughout this step.

Install the fluid pump.





80. CAUTION: The special tools must be used to correctly align the pump with the adapter plate to reduce gear noise, bushing failure and leakage.

Using the special tool, align the fluid pump to the adapter plate.





81. Install 6 screws. Tighten the screws in a star pattern.
^ Tighten to 25 Nm (18 ft. lbs.).





82. Remove the special tools and install the 2 remaining screws.
^ Tighten to 25 Nm (18 ft. lbs.).





83. CAUTION: Do not allow overdrive band adjustment screw to back out. Band strut could fall out of position.

CAUTION: Install, but do not tighten, a new locknut on the band adjustment screw. Apply petroleum jelly to the locknut seal.

Install a new locknut on the band adjustment screw





84. CAUTION: The overdrive servo must be installed prior to band adjustment.

Using the special tool, tighten the overdrive band adjustment screw. Then back off the screw exactly (2) turns and hold that position.
^ Tighten to 14 Nm (10 ft. lbs.).





85. Tighten the overdrive band locknut.
1 Hold the overdrive band adjustment screw stationary.
2 Tighten the overdrive band locknut.
^ Tighten to 54 Nm (40 ft. lbs.).





86. CAUTION: Do not allow the intermediate band adjusting screw to back out. Band strut could fall out of position.

CAUTION: Install, but do not tighten, a new locknut on the band adjustment screw. Apply petroleum jelly to the locknut seal.

Install new nut on the band adjustment screw.





87. CAUTION: The intermediate servo must be installed prior to band adjustment.

Tighten the intermediate band adjustment screw. Then back off the screw exactly (2) turns and hold that position.
^ Tighten to 14 Nm (10 ft. lbs.).





88. Tighten the intermediate band locknut.
1 Hold the intermediate band adjustment screw stationary.
2 Tighten the intermediate band locknut.
^ Tighten to 54 Nm (40 ft. lbs.).





89. Tighten the center support screw.
^ Tighten to 11 Nm (8 ft. lbs.).





90. Using the special tools, carry out the air pressure test procedure.





91. Install the special tools into the transmission case.





92. Using the special tools, install the main control valve body and loosely install the screws.
1 Install the short screw.
2 Install the screw with the larger head.
3 Install the remaining screws.





93. Remove the special tools and loosely install the screw.





94. Tighten the screws in the sequence shown.
^ Tighten to 10 Nm (89 inch lbs.).





95. With the manual lever in the NEUTRAL position, install the manual valve detent spring.
^ Tighten to 10 Nm (89 inch lbs.).





96. Install new O-ring seals on the solenoid body connector. Lubricate the O-ring seals with clean automatic transmission fluid.





97. CAUTION: Inspect the transmission case bore to make sure it is free of foreign material and not damaged. If damaged, transmission leak may occur.

Install the solenoid body. Tighten bolts in the sequence shown.
^ Tighten to 8 Nm (71 inch lbs.).





98. Install the reverse servo. Tighten the bolts in the sequence shown in 2 stages.
^ Stage 1: Tighten bolts to 5 Nm (44 ft. lbs.).
^ Stage 2: Tighten bolts to 11 Nm (8 ft. lbs.).





99. CAUTION: Lubricate the fluid filter seals with clean automatic transmission fluid or they may be damaged.

NOTE: Make sure that the fluid filter seals are correctly seated on the filter.

Lubricate the seals and install the transmission fluid filter.
^ Tighten to 10 Nm (89 inch lbs.).





100. NOTE: The transmission fluid pan gasket is reusable. Clean and inspect for damage. If not damaged, the gasket should be reused.

Install the transmission fluid pan and gasket and loosely install the screws.