Operation CHARM: Car repair manuals for everyone.

Principles of Operation

PRINCIPLES OF OPERATION

Power Locks
The power lock/unlock feature requests all doors, including the liftgate, to lock or unlock upon a request from the door lock control switch, the keyless entry keypad or the remote keyless entry (RKE) transmitter. Power locking and unlocking of the doors functions independently of the ignition key position, vehicle speed or transaxle position. The smart junction box (SJB) activates internal relays to supply the correct voltage and grounds for the door lock actuators.

If all doors, liftgate and hood (with perimeter alarm) are closed when a lock command is received, the turn signals provide 1 flash. If any doors, liftgate or hood (with alarm) are ajar, then no flash occurs.

Autolock
If the vehicle is equipped with the autolock feature, there are 4 methods to enable/disable the feature: using the keyless entry keypad (if equipped), using the LH front door lock control switch, using the message center (if equipped) or the scan tool.

The autolock feature automatically and conditionally locks all doors as a convenience to the customer. This feature operates only when the key is in the ON position.

Autolock occurs when all doors are closed (including the liftgate), the feature has seen a brake pedal application while speed is less than 5 km/h (3 mph), and then the speed increases to 5 km/h (3 mph) or greater.

Relock is dependent on an autolock event happening first.

Relock occurs after a door is opened, the feature has seen a brake pedal application while speed is less than 5 km/h (3 mph), all doors become closed again, and then the speed increases to 5 km/h (3 mph) or greater.

Smart Unlock
The smart unlock feature prevents the LH front door from locking with the key in the ignition lock cylinder. When the SJB receives a lock command from a door lock control switch and the key is in the ignition lock cylinder with the LH front door open, the SJB commands the LH front door to unlock.

RKE External Antenna
The SJB uses an external coaxial antenna to receive RKE transmitter signals.

















RKE Transmitter
The RKE transmitter:
- locks or unlocks all vehicle doors and liftgate without a key.
- unlocks/opens a RH power sliding door and/or LH power sliding door (if equipped).
- opens/closes the power liftgate (if equipped).
- activates and deactivates the panic alarm.
- arms and disarms the perimeter anti-theft system (if equipped).

The RKE transmitter has a minimum operating range of 10 m (33 ft).

RKE Transmitter Lock/Unlock Control - Unlock
The RKE transmitter provides unlock functions independently of key position, vehicle speed, or transaxle position. The RKE transmitter provides a 2-step process for unlocking the doors. Upon receipt of the first request for unlocking the doors, the RKE transmitter requests the SJB to unlock the LH front door only and activate perimeter lighting (if equipped). If another unlock request is received within 3 seconds of the first, the RKE transmitter requests that both front doors, sliding doors and liftgate be unlocked.

RKE Transmitter Lock/Unlock Control - Lock
The RKE transmitter provides lock functions independently of key position, vehicle speed or transaxle position. The RKE transmitter requests that all the doors be locked when the RKE transmitter LOCK button is pressed. When the LOCK button is pressed once, all doors lock. If the LOCK button is pressed again within 3 seconds of the first, the horn chirps to confirm all doors (and hood, if equipped with alarm) are locked and closed. If any door, liftgate, or hood (with perimeter alarm) is ajar when the second lock request is received, 2 chirps are heard.

RKE Transmitter - LH/RH Power Sliding Door Open/Close
The RKE transmitter provides open and close functionality for power sliding doors when the transaxle is in PARK (P) and the speed is less than 5 km/h (3 mph). Pressing the power sliding door button on the RKE transmitter twice within 3 seconds opens the door. With the power sliding door open, pressing the power sliding door button twice within 3 seconds closes the door.

RKE Transmitter - Power Liftgate Open/Close
The RKE transmitter provides open/close functionality for the power liftgate (if equipped). When in PARK (P) or if the vehicle speed is less than 5 km/h (3 mph) with the liftgate closed, pressing the power liftgate button on the RKE transmitter opens the liftgate. With the liftgate open, pressing the power liftgate button twice within 3 seconds closes the power liftgate.

Panic Alarm
The panic alarm feature provides audible and visual alarms which are evident from the exterior of the vehicle. Activation of the panic alarm is accomplished by pressing the PANIC button on an RKE transmitter whenever the key is in the OFF position. The SJB requests that the turn signals are flashed and the horn sounds until the PANIC button is pressed again, 2 minutes and 45 seconds has elapsed since the time of activation, or the key is cycled to the ON position.

Perimeter Lighting
The perimeter lighting feature illuminates the exterior of the vehicle while the user approaches and enters the vehicle to provide better visibility to the user.

The perimeter lighting feature requests the headlamps and parking/position lamps to be on when the key is in the OFF position and the customer activates an external unlock feature (RKE transmitter, keyless entry keypad, door lock cylinder). The perimeter lighting feature requests the headlamps and park/position lamps to be off when 25 seconds have elapsed since the last external unlock activation, or the customer activates an external lock feature (RKE transmitter, keyless entry keypad), or the key is cycled to a position other than OFF.

Keyless Entry Keypad
The keyless entry keypad, located on the exterior of the LH front door, provides a method for the customer to access their vehicle without a key or RKE transmitter. The keyless entry keypad feature:
- locks all doors and liftgate while arming the perimeter alarm (if equipped).
- unlocks only the LH front door and disarms the perimeter alarm (if equipped).
- unlocks all doors and liftgate.
- programs/erases the customer key code.
- enables/disables autolocking.
- opens/closes the power sliding doors (if equipped).

The keyless entry keypad feature operates independently of key position status, vehicle speed, or transaxle position. When an keyless entry keypad button is pressed, the keyless entry keypad buttons illuminate to provide better visibility. If LOCK ALL DOORS is entered, or 5 seconds have elapsed since the last button press, the illumination is turned off.

Each vehicle equipped with an keyless entry keypad is programmed with a 5-digit factory keyless entry keypad code. This code is provided to the customer through a wallet card in the Owner's Literature package. In addition, this code is available through a diagnostic tool and is also printed on the SJB label. A personal keyless entry keypad code can be programmed into the SJB. When entering codes, each digit must be entered within 5 seconds of the prior digit.

Anti-Scan Feature
If the wrong code is entered 7 times (35 consecutive button presses), the keyless entry keypad goes into an anti-scan mode. This mode disables the keyless entry keypad for 1 minute and the keyless entry keypad lamp flashes.

The anti-scan feature turns off after:
- one minute of keyless entry keypad inactivity.
- pressing the UNLOCK button on the RKE transmitter.
- the key is turned to the ON position.

Unlocking the Doors and Liftgate with the Keyless Entry Keypad
To unlock the LH front door, enter either the factory set code or the personal code (each digit must be pressed within 5 seconds of the prior digit). The interior lamps will illuminate.

To unlock all the doors, enter either the factory set code or the personal code (LH front door unlocks) and press the 3/4 control within 5 seconds.

Opening and Closing the Sliding Doors with the Keyless Entry Keypad
To open or close the sliding door, enter either the factory set code or the personal code (each digit must be pressed within 5 seconds of the prior digit) then press the 5/6 button for the LH side door or 9/0 for the RH side door.

Locking the Doors with the Keyless Entry Keypad
It is not necessary to enter the factory set or personal code prior to locking all the doors. To lock all the doors, press the 7/8 and 9/0 controls at the same time.

Central Locking/Unlocking
The central locking/unlocking function is independent of the ignition switch and transmission range selector lever position. Central unlocking of all the doors is accomplished with:
- LH or RH front door lock control switches (unless the unlock inhibit feature is enabled).
- two unlock commands from the RKE transmitter within 3 seconds.
- the keyless entry keypad.

Central locking of all doors is accomplished with:
- the door lock control switches.
- a lock command from the RKE transmitter.
- the keyless entry keypad (if equipped).

When the vehicle is in an armed or full-alarm security state, any unlock command from the door lock control switches is ignored if the unlock inhibit feature is enabled. The door lock control switches are enabled if a valid unlock command is received from the RKE transmitter, the keyless entry keypad, or the key is cycled to ON.

Smart Junction Box (SJB) Additional Features
The SJB can also be programmed to enable/disable the following features:
- Perimeter lighting feature
- Unlock inhibit feature

Perimeter Lighting Programming

NOTE: All of the doors must be closed during the perimeter lighting programming procedure.

1. Turn the key to ON.
2. Press the UNLOCK button 3 times.
3. Turn the key to OFF.
4. Press the UNLOCK button 3 times.
5. Turn the key to ON. The horn will chirp to indicate entry into the driver configuration mode.
6. Press the UNLOCK button, then press the UNLOCK button again. The horn chirps once if the perimeter lighting feature is deactivated or it chirps twice (1 short chirp and 1 long chirp) if the perimeter lighting feature is activated.
7. Turn the key to OFF. The horn chirps to confirm the procedure is complete.

Unlock Inhibit Programming

NOTE: All of the doors must be closed during the unlock inhibit programming procedure.

1. Turn the key to ON.
2. Press the UNLOCK button 3 times.
3. Turn the key to OFF.
4. Press the UNLOCK button 3 times.
5. Turn the key to ON. The horn will chirp to indicate entry into the driver configuration mode.
6. Press the LOCK button, then press the LOCK button again. The horn chirps once if the unlock inhibit feature is deactivated or it chirps twice (1 short chirp and 1 long chirp) if the unlock inhibit feature is just activated.
7. Turn the key to OFF. The horn chirps to confirm the procedure is complete.