Instrument Panel

INSTRUMENT PANEL

Exploded View







Removal and Installation
1. Remove the A-pillar and LH cowl side trim panels.�Service and Repair
2. Remove the transmission selector lever. Service and Repair
3. Depower the supplemental restraint system (SRS). Supplemental Restraint System (SRS) Depowering and Repowering
4. Remove the instrument panel side finish panels.
5. Remove the instrument panel center finish panel.
- Disconnect the electrical connectors.

6. Remove the RH cowl side panel and disconnect the instrument panel connectors behind it in this order.
1 Disconnect the bulkead electrical connector and detach it from the cowl.
2 Disconnect the electrical connector.
3 Disconnect the inertia switch electrical connector.
4 Disconnect the 2 ground strap bolts.







7. Lower the glove compartment and disconnect the instrument panel harness connectors.
1 Disconnect the vacuum harness connector.
2 Disconnect the instrument panel harness electrical connectors.







8. Disconnect the automatic temperature control solenoid and manifold electrical connector.







9. Disconnect the antenna lead-in cable.







10. Remove the parking brake release handle.
1 Remove the 2 screws.
2 Remove the release handle.







11. Disconnect the LH side instrument panel bulkhead electrical connector.







12. CAUTION: Do not allow the steering column shaft to rotate while the intermediate shaft is disconnected or damage to the clockspring may result. If there is evidence that the shaft has rotated, the clockspring must be removed and recentered.

Place the steering wheel and the front wheels in the straight-ahead position.
- Turn the ignition switch to the OFF position and remove the key.

13. NOTE: Install a new upper steering column shaft-to-steering column bolt.

Remove and discard the upper steering column shaft-to-steering column bolt.
- To install, tighten to 30 Nm (22 lb-ft).







14. From atop the accelerator pedal, disconnect the RH adjustable pedal electrical connector (if equipped).







15. From the LH side of the brake pedal, disconnect the adjustable pedal motor electrical connector (if equipped).







16. NOTE: RH side shown, LH side similar.

Remove the RH and LH instrument panel center braces.
1 Remove the 4 instrument panel brace bolts.
2 Remove the 4 instrument panel brace nuts.
- To install, tighten to 9 Nm (80 lb-in).







17. Remove the 2 instrument panel bolts.
- Remove the covers and remove the bolts.
- To install, tighten to 30 Nm (22 lb-ft).

18. Remove the driver front seat. Service and Repair
19. Position the carpet away from the restraints control module (RCM).
20. Disconnect the small RCM electrical connector.







21. Disconnect the stability control sensor cluster jumper harness electrical connector and detach the instrument panel harness from the floorpan.







22. Loosen the RH instrument panel bolts one half of the bolt length, but do not completely remove the bolts.
- To install, tighten to 30 Nm (22 lb-ft).

23. NOTE: The instrument panel may be supported by installing long bolts or threaded rods with the same diameter and thread pitch (in place of the LH instrument panel bolts), to support the instrument panel while allowing it to be moved away from the dash panel.

Remove the 2 LH instrument panel bolts and correctly support the instrument panel.
- To install, tighten to 30 Nm (22 lb-ft).

24. Position the LH side of the instrument panel rearward and disconnect the smart junction box (SJB) electrical connectors.







25. Position the instrument panel back to the original position and remove the LH instrument panel supports (if necessary).

26. CAUTION:
- To avoid damage to the instrument panel, an assistant is required to support the panel before carrying out this step.
- Before removing the instrument panel, make sure all electrical connector wiring is free and not hindered or damage to the wire harness may occur.

Remove the RH instrument panel bolts and remove the instrument panel.

27. To install, reverse the removal procedure.