Operation CHARM: Car repair manuals for everyone.
Home >> Mercury Truck >> 2009 >> Mariner 4WD V6-3.0L >> Repair and Diagnosis >> Restraints and Safety Systems >> Air Bag Systems >> Testing and Inspection >> Pinpoint Tests >> Pinpoint Test - Restraints Control Module (RCM) >> Pinpoint Test L: DTCs B0090:11, B0090:81, B0090:93 And B0090:96

Pinpoint Test L: DTCs B0090:11, B0090:81, B0090:93 And B0090:96




Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS)

Pinpoint Test - Restraints Control Module (RCM)

Pinpoint Test L: DTCs B0090:11, B0090:81, B0090:93 and B0090:96

Refer to Wiring Diagram Set 46 (Escape/Mariner, Escape Hybrid/Mariner Hybrid), Supplemental Restraint System for schematic and connector information. Diagrams By Number

Normal Operation

The Restraints Control Module (RCM) checks the LH front impact severity sensor (Left Frontal Restraints Sensor) and circuits for the following faults:

- Open circuit
- Short to voltage
- Short to ground

If a fault is detected, the RCM will store DTC B0090:11, B0090:81, B0090:93 or B0090:96 in memory and send a message to the Instrument Cluster (IC) module to illuminate the air bag warning indicator.

B0090:11-B0090:96:





This pinpoint test is intended to diagnose the following:
- Wiring, terminals or connectors
- LH front impact severity sensor (Left Front Restraints Sensor)
- RCM



PINPOINT TEST L: DTCs B0090:11, B0090:81, B0090:93 AND B0090:96

WARNING: Do not handle, move or change the original horizontal mounting position of the restraints control module (RCM) while the RCM is connected and the ignition switch is ON. Failure to follow this instruction may result in the accidental deployment of the Safety Canopy(R) and cause serious personal injury or death.

NOTICE: Use the correct probe adapter(s) from the Flex Probe Kit when taking measurements. Failure to use the correct probe adapter(s) may damage the connector.

Most faults are due to connector and/or wiring concerns. Carry out a thorough inspection and verification before proceeding with the pinpoint test. Inspection and Verification

NOTE: Supplemental Restraint System (SRS) components should only be disconnected or reconnected when instructed to do so within a pinpoint test step. Failure to follow this instruction may result in incorrect diagnosis of the SRS.

NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.

NOTE: Do not probe any impact sensor. The impact sensor can not be tested using a multi-meter.

-------------------------------------------------
L1 RETRIEVE RCM DTCs


- Enter the following diagnostic mode on the scan tool: Self Test - RCM.
- Was DTC B0090:11, B0090:81, B0090:93 or B0090:96 retrieved on-demand during self-test?

Yes
This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-demand during self-test.

For DTC B0090:11, GO to L2.

For DTC B0090:93, GO to L5.

For DTC B0090:81 or B0090:96, INSTALL a new LH front impact severity sensor. REFER to Front Impact Severity Sensor Front Impact Severity Sensor. GO to L11.

No
The fault is intermittent when present as a CMDTC only. GO to L10.

-------------------------------------------------
L2 CHECK LEFT FRONTAL RESTRAINTS SENSOR DTC FOR A FAULT STATUS CHANGE (SHORT TO GROUND INDICATED)


NOTE: This pinpoint test step will attempt to change the fault reported by the RCM by inducing a different fault condition. If the fault reported changes, this indicates the RCM is functioning correctly and is not the source of the fault.

- Ignition OFF.
- Depower the SRS. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Disconnect: LH Front Impact Severity Sensor C1464.
- Repower the SRS. Do not prove out the SRS at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Enter the following diagnostic mode on the scan tool: Self Test - RCM.
- Did the on-demand DTC change from B0090:11 to B0090:93?

Yes
INSTALL a new LH front impact severity sensor. REFER to Front Impact Severity Sensor Front Impact Severity Sensor. GO to L11.

No
GO to L3.

-------------------------------------------------
L3 CHECK LH FRONT IMPACT SEVERITY SENSOR CIRCUIT FOR A SHORT TO GROUND


- Ignition OFF.
- Depower the SRS. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Disconnect: RCM C2041a and C2041b.
- Measure the resistance between LH front impact severity sensor C1464-1, circuit VR213 (VT/GN), harness side and ground.




- Is the resistance greater than 10,000 ohms?

Yes
GO to L4.

No
REPAIR circuit VR213 (VT/GN). GO to L11.

-------------------------------------------------
L4 CHECK FOR A SHORT BETWEEN LH FRONT IMPACT SEVERITY SENSOR CIRCUITS


- Measure the resistance between LH front impact severity sensor C1464-1, circuit VR213 (VT/GN), harness side and C1464-2, circuit RR129 (YE/GY), harness side.




- Is the resistance greater than 10,000 ohms?

Yes
GO to L9.

No
REPAIR circuits VR213 (VT/GN) and RR129 (YE/GY). GO to L11.

-------------------------------------------------
L5 CHECK LH FRONT IMPACT SEVERITY SENSOR AND RCM CONNECTIONS (NO OPERATION INDICATED)


- Ignition OFF.
- Inspect LH front impact severity sensor C1464 to be fully seated and locked. Seat and lock connector as necessary.
- Gain access to the RCM and inspect C2041a and C2041b to be sure they are fully seated and locked. Seat and lock the connector(s) as necessary. Refer to Restraints Control Module (RCM) Service and Repair.
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: Self Test - RCM.
- Was DTC B0090:93 retrieved on-demand during self-test?

Yes
GO to L6.

No
Fault corrected. GO to L11.

-------------------------------------------------
L6 CHECK LH FRONT IMPACT SEVERITY SENSOR CIRCUITS FOR A SHORT TO VOLTAGE


- Ignition OFF.
- Depower the SRS. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Disconnect: RCM C2041a and C2041b.
- Disconnect: LH Front Impact Severity Sensor C1464.
- Repower the SRS. Do not prove out the SRS at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Ignition ON.
- Measure the voltage between LH front impact severity sensor:
- C1464-1, circuit VR213 (VT/GN), harness side and ground.
- C1464-2, circuit RR129 (YE/GY), harness side and ground.




- Is voltage present on either circuit?

Yes
REPAIR circuit VR213 (VT/GN) or RR129 (YE/GY). GO to L11.

No
GO to L7.

-------------------------------------------------
L7 CHECK LH FRONT IMPACT SEVERITY SENSOR CIRCUITS FOR AN OPEN


- Ignition OFF.
- Depower the SRS. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Measure the resistance between RCM C2041b, harness side and LH front impact severity sensor C1464, harness side using the following chart.









- Are the resistances less than 0.5 ohm?

Yes
GO to L8.

No
REPAIR circuit VR213 (VT/GN) or RR129 (YE/GY). GO to L11.

-------------------------------------------------
L8 CHECK LEFT FRONTAL RESTRAINTS SENSOR DTC FOR A FAULT STATUS CHANGE (NO OPERATION INDICATED)


NOTE: This pinpoint test step will attempt to change the fault reported by the RCM by inducing a different fault condition. If the fault reported changes, this indicates the RCM is functioning correctly and is not the source of the fault.

- Connect: RCM C2041a and C2041b.
- Connect a fused jumper wire between LH front impact severity sensor C1464-1, circuit VR213 (VT/GN), harness side and C1464-2, circuit RR129 (YE/GY), harness side.
- Repower the SRS. Do not prove out the SRS at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Enter the following diagnostic mode on the scan tool: Self Test - RCM.
- Did the on-demand DTC change from B0090:93 to B0090:11?

Yes
INSTALL a new sensor. REFER to Front Impact Severity Sensor Front Impact Severity Sensor. GO to L11.

No
GO to L9.

-------------------------------------------------
L9 CONFIRM THE RCM FAULT


NOTE: Make sure all restraint system components, sensor electrical connectors and the RCM electrical connectors are connected before carrying out the self-test. If not, DTCs will be recorded.

- Ignition OFF.
- Depower the SRS. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Prior to reconnecting any previously disconnected SRS component:
- inspect connector(s) (including any in-line connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
- inspect wire harness for any damage, pinched, cut or pierced wires.
- inspect C2041a and C2041b connector position assurance lever/lock for correct operation. Refer to Restraints Control Module (RCM) Service and Repair.
- repair any concerns found. Refer to Wiring Diagram Set 5 (Escape/Mariner, Escape Hybrid/Mariner Hybrid), Connector Repair Procedures for schematic and connector information. Diagrams By Number

- Connect: RCM C2041a and C2041b.
- Connect: LH Front Impact Severity Sensor C1464.
- Repower the SRS. Do not prove out the SRS at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Enter the following diagnostic mode on the scan tool: Self Test - RCM.
- Was the original DTC retrieved on-demand during self-test?

Yes
INSTALL a new RCM. REFER to Restraints Control Module (RCM) Service and Repair. GO to L11.

No
In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. SRS components should only be installed when directed to do so in the pinpoint test. GO to L10.

-------------------------------------------------
L10 CHECK FOR AN INTERMITTENT FAULT


- Ignition OFF.
- Depower the SRS. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Disconnect: LH Front Impact Severity Sensor C1464.
- Disconnect: RCM C2041a and C2041b.
- Inspect for the following:
- inspect harness and component connectors for loose or spread terminals and loose or frayed wire connections at terminals.
- inspect wire harness for any damage, pinched, cut or pierced wires.
- inspect RCM C2041a and C2041b connector position assurance lever/lock for correct operation. Refer to Restraints Control Module (RCM) Service and Repair.
- repair any concerns found. Refer to Wiring Diagram Set 5 (Escape/Mariner, Escape Hybrid/Mariner Hybrid), Connector Repair Procedures for schematic and connector information. Diagrams By Number

- Connect: All Previously Disconnected Component(s)/Connector(s).
- Repower the SRS. Do not prove out the SRS at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: Self Test - RCM.
- Was DTC B0090:11, B0090:81, B0090:93 or B0090:96 retrieved on-demand during self-test?

Yes
The fault condition is now present. This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-demand during self-test.

For DTC B0090:11, GO to L2.

For DTC B0090:93, GO to L5.

For DTC B0090:81 or B0090:96, INSTALL a new LH front impact severity sensor. REFER to Front Impact Severity Sensor Front Impact Severity Sensor. GO to L11.

No
The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. SRS components should only be installed when directed to do so in the pinpoint test. REPAIR any intermittent wiring, terminal or connector concerns found.
GO to L11.

-------------------------------------------------
L11 CHECK FOR ADDITIONAL SRS DTCs


- Ignition OFF.
- WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
- Reconnect all SRS components (if previously disconnected).
- If previously directed to depower the SRS, repower the SRS. Do notprove out the SRS at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: Self Test - Restraints.
- NOTE: When selecting Restraints from the Self Test menu, DTCs will be retrieved from the RCM and OCSM.
- Are any RCM and/or OCSM DTCs retrieved?

Yes
Do not clear any DTCs until all DTCs have been resolved. GO to the DTC Charts for pinpoint test direction. [1][2]Diagnostic Trouble Code Descriptions

No
CLEAR all RCM and OCSM CMDTCs. PROVE OUT the SRS. Repair is complete. RETURN the vehicle to the customer.

-------------------------------------------------
pro multis · About Operation CHARM