Operation CHARM: Car repair manuals for everyone.
Home >> Mercury Truck >> 2011 >> Mariner 4WD V6-3.0L >> Repair and Diagnosis >> Restraints and Safety Systems >> Air Bag Systems >> Testing and Inspection >> Pinpoint Tests >> Pinpoint Test X: DTCs B1214:11, B1214:12, B1214:13 and B1214:1A

Pinpoint Test X: DTCs B1214:11, B1214:12, B1214:13 and B1214:1A




Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS)

Pinpoint Tests

Pinpoint Test X: DTCs B1214:11, B1214:12, B1214:13 and B1214:1A

Refer to Wiring Diagram Set 46 (Escape/Mariner, Escape Hybrid/Mariner Hybrid), Supplemental Restraint System for schematic and connector information. Diagrams By Number

Normal Operation

The Restraints Control Module (RCM) continuously monitors the passenger safety belt retractor and circuits for the following faults:

- Resistance out of range
- Unexpected voltage
- Short to ground
- Faulted passenger safety belt retractor

If a fault is detected, the RCM will store DTC B1214:11, B1214:12, B1214:13 or B1214:1A in memory and send a message to the Instrument Cluster (IC) module to illuminate the air bag warning indicator.

The RCM analyzes the deployment loop resistance and uses this measurement in combination with an age correction factor to determine if a fault exists. The value displayed in the PID is the deployment loop resistance as measured by the RCM. If the value displayed is lower or higher than the desired range (refer to diagram below), the RCM can set a DTC. As the deployment loop resistance drifts farther outside the desired range, the chance for a DTC increases. The RCM fault trigger threshold may vary as the vehicle ages. Small variations in resistance can occur due to the effect of road vibrations on terminal fit and/or temperature changes. These variables can result in an intermittent fault. For this reason, the test will require the PID value to be within the desired range before the fault is considered repaired, regardless if the module is reporting an on-demand DTC at time of diagnosis. Following this direction will help make sure that minor changes in resistance do not create a repeat concern. This test will use a process of elimination to diagnose each part of the deployment loop circuit including:

- Wiring
- Connections
- Passenger safety belt retractor
- RCM










This pinpoint test is intended to diagnose the following:
- Wiring, terminals or connectors
- Passenger safety belt retractor
- RCM


PINPOINT TEST X: DTCs B1214:11, B1214:12, B1214:13 and B1214:1A

WARNING: Do not handle, move or change the original horizontal mounting position of the restraints control module (RCM) while the RCM is connected and the ignition switch is ON. Failure to follow this instruction may result in the accidental deployment of the Safety Canopy(R) and cause serious personal injury or death.

WARNING: Never disassemble or tamper with safety belt buckle/retractor pretensioners or adaptive load limiting retractors or probe the electrical connectors. Failure to follow this instruction may result in the accidental deployment of the safety belt pretensioners or adaptive load limiting retractors which increases the risk of serious personal injury or death.

NOTICE: Use the correct probe adapter(s) from the Flex Probe Kit when taking measurements. Failure to use the correct probe adapter(s) may damage the connector.

Most faults are due to connector and/or wiring concerns. Carry out a thorough inspection and verification before proceeding with the pinpoint test. Inspection and Verification

NOTE:Supplemental Restraint System (SRS) components should only be disconnected or reconnected when instructed to do so within a pinpoint test step. Failure to follow this instruction may result in incorrect diagnosis of the SRS.

NOTE: Always make sure the correct SRS component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar. Check the part number listed in the Ford Catalog Advantage(TM) or equivalent to make sure the correct component is being installed. If an incorrect SRS component is installed, DTCs may set.

NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.

-------------------------------------------------
X1 RETRIEVE RCM DTCs

- Ignition ON.
- Enter the following diagnostic mode on the scan tool: Self Test - RCM.
- Was DTC B1214:11, B1214:12, B1214:13 or B1214:1A retrieved on-demand during self-test?

Yes
This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-demand during self-test.

For DTC B1214:13 or B1214:1A, GO to X2.

For DTC B1214:11, GO to X8.

For DTC B1214:12, GO to X10.

No
This is an intermittent fault when present as a CMDTC only. The fault condition is not present at this time.

For DTC B1214:13 or B1214:1A, GO to X13.

For DTC B1214:11, GO to X14.

For DTC B1214:12, GO to X15.

-------------------------------------------------
X2 CHECK THE PASSENGER SEATBELT RETRACTOR DEPLOYMENT CONTROL RESISTANCE (DEPLOY_24_R) PID

- Enter the following diagnostic mode on the scan tool: DataLogger - RCM.
- DEPLOY_24_R PID
- Does the PID value read between 1.7 and 2.78 ohms?

Yes
GO to X12.

No
GO to X3.

-------------------------------------------------
X3 CHECK THE PASSENGER SEATBELT RETRACTOR DEPLOYMENT CONTROL RESISTANCE (DEPLOY_24_R) PID WHILE CARRYING OUT THE HARNESS TEST

- While monitoring the DEPLOY_24_R PID carry out the harness test of the passenger retractor circuits and accessible connectors (including any in-line connectors), by wiggling connectors and flexing the wire harness.
- Does the PID value read between 1.7 and 2.78 ohms while carrying out the harness test?

Yes
DEPOWER the SRS and REPAIR the connector, terminals or wire harness as needed.

Refer to Wiring Diagram Set 5 (Escape/Mariner, Escape Hybrid/Mariner Hybrid), Connector Repair Procedures for schematic and connector information. Diagrams By Number

GO to X17.

No
For PID value less than 1.7 ohms, GO to X4.

For PID value greater than 2.78 ohms, GO to X6.

-------------------------------------------------
X4 CHECK THE PASSENGER SEATBELT RETRACTOR DEPLOYMENT CONTROL DTC FOR A FAULT STATUS CHANGE (LOW RESISTANCE INDICATED)

NOTE: This pinpoint test step will attempt to change the fault reported by the RCM by inducing a different fault condition. If the fault reported changes, this indicates the RCM is functioning correctly and is not the source of the fault.

- Ignition OFF.
- Depower the SRS. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Disconnect: Passenger Safety Belt Retractor C303.
- Repower the SRS. Do not prove out the SRS at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: Self Test - RCM.
- DIAGNOSTIC TIP: When viewing DTCs with the driver safety belt retractor disconnected, an open circuit fault would normally be retrieved.
- Did the on-demand DTC change from B1214:1A to B1214:13?

Yes
GO to X11.

No
GO to X5.

-------------------------------------------------
X5 CHECK FOR A SHORT BETWEEN PASSENGER SAFETY BELT RETRACTOR CIRCUITS

- Ignition OFF.
- Depower the SRS. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Disconnect: RCM C2041A and C2041B.
- Measure the resistance between the passenger safety belt retractor C303-2, circuit CR147 (GN/OG), harness side and C303-1, circuit RR147 (YE/VT), harness side.





- Is the resistance greater than 10,000 ohms?

Yes
GO to X12.

No
REPAIR circuits CR147 (GN/OG) and RR147 (YE/VT). GO to X17.

-------------------------------------------------
X6 CHECK THE PASSENGER SAFETY BELT RETRACTOR CIRCUITS FOR AN OPEN

- Ignition OFF.
- Depower the SRS. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Disconnect: Passenger Safety Belt Retractor C303.
- Disconnect: RCM C2041A and C2041B.
- Measure the resistance between RCM C2041B, and passenger safety belt retractor C303, harness side using the following chart.










- Are the resistances less than 0.5 ohm?

Yes
GO to X7.

No
REPAIR circuit CR147 (GN/OG) or RR147 (YE/VT). GO to X17.

-------------------------------------------------
X7 CHECK THE PASSENGER SEATBELT RETRACTOR DEPLOYMENT CONTROL DTC FOR A FAULT STATUS CHANGE (OPEN INDICATED)

NOTE: This pinpoint test step will attempt to change the fault reported by the RCM by inducing a different fault condition. If the fault reported changes, this indicates the RCM is functioning correctly and is not the source of the fault.

- Connect: RCM C2041A and C2041B.
- Connect a fused jumper wire between the passenger safety belt retractor C303-2, circuit CR147 (GN/OG), harness side and C303-1, circuit RR147 (YE/VT), harness side.
- Repower the SRS. Do not prove out the SRS at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: Self Test - RCM.
- DIAGNOSTIC TIP: When viewing DTCs with the passenger safety belt retractor circuits shorted together, a low resistance fault would normally be retrieved.
- Did the on-demand DTC change from B1214:13 to B1214:1A?

Yes
GO to X11.

No
GO to X12.

-------------------------------------------------
X8 CHECK THE PASSENGER SEATBELT RETRACTOR DEPLOYMENT CONTROL DTC FOR A FAULT STATUS CHANGE (SHORT TO GROUND INDICATED)

NOTE: This pinpoint test step will attempt to change the fault reported by the RCM by inducing a different fault condition. If the fault reported changes, this indicates the RCM is functioning correctly and is not the source of the fault.

- Ignition OFF.
- Depower the SRS. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Disconnect: Passenger Safety Belt Retractor C303.
- Repower the SRS. Do not prove out the SRS at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: Self Test - RCM.
- DIAGNOSTIC TIP: When viewing DTCs with the passenger safety belt retractor disconnected, an open circuit fault would normally be retrieved.
- Did the on-demand DTC change from B1214:11 to B1214:13?

Yes
GO to X11.

No
GO to X9.

-------------------------------------------------
X9 CHECK THE PASSENGER SAFETY BELT RETRACTOR CIRCUITS FOR A SHORT TO GROUND

- Ignition OFF.
- Depower the SRS. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Disconnect: RCM C2041A and C2041B.
- Measure the resistance between the passenger safety belt retractor:
- C303-2, circuit CR147 (GN/OG), harness side and ground.
- C303-1, circuit RR147 (YE/VT), harness side and ground.





- Are the resistances greater than 10,000 ohms?

Yes
GO to X12.

No
REPAIR circuit CR147 (GN/OG) or RR147 (YE/VT). GO to X17.

-------------------------------------------------
X10 CHECK THE PASSENGER SAFETY BELT RETRACTOR CIRCUITS FOR A SHORT TO VOLTAGE

- Ignition OFF.
- Depower the SRS. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Disconnect: Passenger Safety Belt Retractor C303.
- Disconnect: RCM C2041A and C2041B.
- Repower the SRS. Do not prove out the SRS at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Ignition ON.
- Measure the voltage between the passenger safety belt retractor:
- C303-2, circuit CR147 (GN/OG), harness side and ground.
- C303-1, circuit RR147 (YE/VT), harness side and ground.





- Is voltage present on either circuit?

Yes
REPAIR circuit CR147 (GN/OG) or RR147 (YE/VT). GO to X17.

No
GO to X12.

-------------------------------------------------
X11 CONFIRM THE PASSENGER SAFETY BELT RETRACTOR FAULT

NOTE: Make sure all restraint system components and the RCM electrical connectors are connected before carrying out the self-test. If not, DTCs will be recorded.

- Ignition OFF.
- Depower the SRS. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- If previously installed, remove the fused jumper wire from the retractor electrical connector.
- Prior to reconnecting any previously disconnected SRS component:
- inspect connector(s) (including any in-line connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
- inspect wire harness for any damage, pinched, cut or pierced wires.
- inspect C2041A and C2041B Connector Position Assurance (CPA) lever/lock for correct operation. Refer to Restraints Control Module (RCM) Service and Repair.
- repair any concerns found.
Refer to Wiring Diagram Set 5 (Escape/Mariner, Escape Hybrid/Mariner Hybrid), Connector Repair Procedures for schematic and connector information. Diagrams By Number

- Connect: Passenger Safety Belt Retractor C303.
- Connect RCM C2041A and C2041B (if previously disconnected).
- Repower the SRS. Do not prove out the SRS at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: Self Test - RCM.
- Was the original DTC retrieved on-demand during self-test?

Yes
INSTALL a new passenger safety belt retractor. REFER to Safety Belt System Seat Belt Retractor. GO to X17.

No
In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. SRS components should only be installed when directed to do so in the pinpoint test.

For DTC B1214:13 or B1214:1A, GO to X13.

For DTC B1214:11, GO to X14.

For DTC B1214:12, GO to X15.

-------------------------------------------------
X12 CONFIRM THE RCM FAULT

NOTE: Make sure all restraint system components and the RCM electrical connectors are connected before carrying out the self-test. If not, DTCs will be recorded.

- Ignition OFF.
- Depower the SRS. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- If previously installed, remove the fused jumper wire from the retractor electrical connector.
- Prior to reconnecting any previously disconnected SRS component:
- inspect connector(s) (including any in-line connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
- inspect wire harness for any damage, pinched, cut or pierced wires.
- inspect C2041A and C2041B CPA lever/lock for correct operation. Refer to Restraints Control Module (RCM) Service and Repair.
- repair any concerns found.
Refer to Wiring Diagram Set 5 (Escape/Mariner, Escape Hybrid/Mariner Hybrid), Connector Repair Procedures for schematic and connector information. Diagrams By Number

- Connect: Passenger Safety Belt Retractor C303.
- Connect: RCM C2041A and C2041B (if previously disconnected).
- Repower the SRS. Do not prove out the SRS at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: Self Test - RCM.
- Was the original DTC retrieved on-demand during self-test?

Yes
INSTALL a new RCM. REFER to Restraints Control Module (RCM) Service and Repair. GO to X17.

No
In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. SRS components should only be installed when directed to do so in the pinpoint test.

For DTC B1214:13 or B1214:1A, GO to X13.

For DTC B1214:11, GO to X14.

For DTC B1214:12, GO to X15.

-------------------------------------------------
X13 CHECK FOR AN INTERMITTENT PASSENGER SEATBELT RETRACTOR PRETENSIONER DEPLOYMENT CONTROL RESISTANCE (DEPLOY_24_R) PID LOW RESISTANCE OR OPEN CIRCUIT FAULT

- Enter the following diagnostic mode on the scan tool: DataLogger - RCM.
- DEPLOY_24_R PID
- Attempt to recreate the fault by wiggling the connectors (including any in-line connectors) and flexing the wire harness.
- Does the PID value read between 1.7 and 2.78 ohms?

Yes
The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. SRS components should only be installed when directed to do so in the pinpoint test. GO to X16.

No
DEPOWER the SRS and REPAIR as necessary.

Refer to Wiring Diagram Set 5 (Escape/Mariner, Escape Hybrid/Mariner Hybrid), Connector Repair Procedures for schematic and connector information. Diagrams By Number

GO to X17.

-------------------------------------------------
X14 CHECK FOR AN INTERMITTENT PASSENGER SEATBELT RETRACTOR PRETENSIONER DEPLOYMENT CONTROL SHORT TO GROUND FAULT

- Attempt to recreate the fault by wiggling connectors (including any in-line connectors) and flexing the wire harness.
- Enter the following diagnostic mode on the scan tool: Self Test - RCM.
- Was DTC B1214:11 retrieved on-demand during self-test?

Yes
DEPOWER the SRS and REPAIR as necessary.

Refer to Wiring Diagram Set 5 (Escape/Mariner, Escape Hybrid/Mariner Hybrid), Connector Repair Procedures for schematic and connector information. Diagrams By Number

GO to X17.

No
The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. SRS components should only be installed when directed to do so in the pinpoint test. GO to X16.

-------------------------------------------------
X15 CHECK FOR AN INTERMITTENT PASSENGER SEATBELT RETRACTOR PRETENSIONER DEPLOYMENT CONTROL SHORT TO VOLTAGE FAULT

- Ignition OFF.
- Depower the SRS. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Disconnect: Passenger Safety Belt Retractor C303.
- Repower the SRS. Do not prove out the SRS at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Ignition ON.
- Attempt to recreate the fault by wiggling connectors (including any in-line connectors) and flexing the wire harness.
- Enter the following diagnostic mode on the scan tool: Self Test - RCM.
- Was DTC B1214:12 retrieved on-demand during self-test?

Yes
DEPOWER the SRS and REPAIR as necessary.

Refer to Wiring Diagram Set 5 (Escape/Mariner, Escape Hybrid/Mariner Hybrid), Connector Repair Procedures for schematic and connector information. Diagrams By Number

GO to X17.

No
The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. SRS components should only be installed when directed to do so in the pinpoint test. GO to X16.

-------------------------------------------------
X16 CHECK THE HARNESS AND CONNECTORS

- Ignition OFF.
- Depower the SRS. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Disconnect the passenger safety belt retractor C303:
- inspect connector(s) (including any in-line connectors) for loose or spread terminals and loose or frayed wire connections at terminals.
- inspect wire harness for any damage, pinched, cut or pierced wires.
- Were any concerns found?

Yes
REPAIR as necessary.

Refer to Wiring Diagram Set 5 (Escape/Mariner, Escape Hybrid/Mariner Hybrid), Connector Repair Procedures for schematic and connector information. Diagrams By Number

GO to X17.

No
The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. SRS components should only be installed when directed to do so in the pinpoint test. GO to X17.

-------------------------------------------------
X17 CHECK FOR ADDITIONAL SRS DTCs

- Ignition OFF.

- WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.

- Reconnect all SRS components (if previously disconnected).
- If previously directed to depower the SRS, repower the SRS. Do not prove out the SRS at this time. Refer to Supplemental Restraint System (SRS) Depowering and Repowering Supplemental Restraint System (SRS) Depowering and Repowering.
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: Self Test - Restraints.

- NOTE: When selecting Restraints from the Self Test menu, DTCs will be retrieved from the RCM and OCSM.

- Are any RCM and/or OCSM DTCs retrieved on-demand during self-test?

Yes
Do not clear any DTCs until all DTCs have been resolved. GO to the DTC Charts for pinpoint test direction. [1][2]Diagnostic Trouble Code Descriptions

No
CLEAR all RCM and OCSM CMDTCs. PROVE OUT the SRS. Repair is complete. RETURN the vehicle to the customer.

-------------------------------------------------
pro multis · About Operation CHARM