Idle Speed Setting - Manual Revisions
84ford19Article No. 84-3-23
SHOP MANUAL REVISIONS - 1984 - IDLE SPEED SETTING
FORD 1984 MUSTANG, LTD, T-BIRD W/3.8L EEC IV
LINCOLN-MERCURY 1984 CAPRI, MARQUIS, COUGAR W/3.8L EEC IV
CALIBRATIONS: All with 3.8L EEC IV
This article changes idle speed setting procedures published in Volumes H and HC of the 1984 Car Shop Manual.
Replace pages 4-57 and 4-58 from the 1984 Emission Diagnosis Manual (H) and pages 4-51 and 4-52 in manual (HC) with the following pages.
OTHER APPLICABLE ARTICLES: None
WARRANTY STATUS: "INFORMATION ONLY"
Idle Speed Setting Procedures
PASSENGER CAR - 50 STATES
3.8L with Electronic Central Fuel Injection (CFI) and D.C. Motor Idle Speed Control (ISC)
Curb Idle Speed Check:
1. Set parking brake and block wheels. If equipped with automatic parking brake, always place in Reverse when checking curb idle. Make all adjustments with engine at normal operating temperature and accessories Off, 2. After engaging transmission in Drive (or Reverse) and idling for 60 seconds, idle rpm should be within specification (Refer to decal for speeds).
NOTE: Curb and fast idle speeds are controlled by the EEC IV processor and the idle speed control device. If the control system is operating properly, these speeds are fixed and cannot be changed by traditional adjustment techniques.
Adjustments are sometimes required to establish the correct operating limits within which the ISC system can properly function. These adjustments, as outlined below, will normally have no direct effect on actual idle speed and generally will not be required unless:
A. Curb idle speed is out of specification as shown on the decal. or
B. The ISC motor requires replacement.
Misadjustment of the operating limits could restrict the operating range of the fSC system, so adjustments of these limits should never be made unless a specific causal factor exists. If these operating limit adjustments do not correct an out of specification curb idle speed condition, it will be necessary to perform the appropriate 3.8L EEC IV diagnostics,
Idle Speed Setting Procedures
Minimum ISC Limit Adjustment
If the curb idle is above specification, verify that the throttle linkage is free, that travel is unobstructed and that cruise control (if equipped) is not holding the throttle open. If it is observed that the throttle lever is not in contact with the fSC motor, but held open by the throttle stop adjusting screw (TSAS), this screw must be adjusted. This is the only reason for adjusting the TSAS as it is strictly a throttle stop and in no way affects idle speeds unless it is holding the throttle open through misadjustment. To adjust the TSAS, the ISC motor must be fully retracted. Therefore, the following TSAS adjustment procedure must be done in the exact sequence shown below:
1. Shut the engine off and remove the air cleaner. In the engine compartment, find the self-test connector and self-test input (STI) connector. These two connectors are located next to each other on the driver's side, behind the strut tower and on the EEC harness.
FIGURE 1 - 3.8L CFI:
2. Connect a jumper wire between the self-test input (STI) connector and the signal return pin on the self-test connector as shown in Figure 1.
3. Turn the ignition key to the run position. Do Not Start Engine.
4. The ISC plunger will retract. Wait until plunger is fully retracted (about ten seconds).
NOTE: If plunger does not retract, refer to EEC IV diagnostics.
5. Shut off the key.
6. Remove the jumper wire.
7. Perform throttle stop adjustments as follows:
^ Using pliers, grasp the TSAS screw threads and turn the screw (Refer to Figure 2) until it is removed from the CFI assembly. Install a new screw.
^ With the throttle plates closed, turn the new screw inward until there is a .005 inch gap between the screw tip and the throttle lever surface which it contacts.
^ Turn the screw inward an additional 1-1/2 turns, 8. Reinstall air cleaner.
Idle Speed Setting Procedures
Maximum ISC Limit Adjustment
If curb idle RPM is below limit or there is reason to suspect that cold engine idle speeds are low (i.e., engine stalls), the idle speed control device may be restricting operation. Check and adjust in the exact sequence as shown below.
1. Shut engine off and remove air cleaner. In the engine compartment, find the self-test connector and self-test input (STI) connector. These two connectors are located next to each other on the driver's side, behind the strut tower and on the EEC harness.
FIGURE 1 - 3.8L CFI:
2. Connect a jumper wire between the STI connector and the signal return pin on the self-test connector as shown in Figure 1.
3. Turn the ignition key to the run position. Do Not Start Engine.
4. The ISC plunger will retract. Wait until plunger is fully retracted (about ten seconds).
NOTE: If plunger does not retract, refer to EEC IV diagnostics.
5. Shut off the key.
6. Remove the jumper wire.
7. ^ Remove the rubber dust cover from the ISC motor tip.
^ Push the tip back toward the motor to remove any lash.
^ Attempt to pass a 9/32 inch (.281 inch) drill bit between the ISC motor tip (which is the idle tracking switch) and the throttle lever. It must pass through while making only light contact with both surfaces. If it does not, loosen the ISC bracket lock screw and turn the ISC bracket adjusting screw until proper clearance is attained.
NOTE: Be sure not to push back the idle tracking switch with the drill bit.
8. Re-tighten the lock screw and replace the rubber dust cover.
9. Reinstall air cleaner.