VCT Solenoid - MIL ON/Trouble Codes Stored
Article No.00-3-7
02/07/00
^ MALFUNCTION INDICATOR LAMP (MIL) - MIL ILLUMINATED - DIAGNOSTIC TROUBLE CODES (DTCS) P1380, P1381, OR P1383 IN MEMORY - NO DRIVEABILITY CONCERN S - VEHICLES WITH 2.0L ENGINE
^ ENGINE - 2.0L - ENGINE OIL CONTAMINATION WITH DIAGNOSTIC TROUBLE CODES (DTCS) P1380, P1381, OR P1383 IN MEMORY - NO DRIVEABILITY CONCERNS
FORD:
1998-2000 CONTOUR, ESCORT ZX2
MERCURY:
1998-2000 MYSTIQUE
1999-2000 COUGAR
ISSUE
The Malfunction Indicator Lamp (MIL) may illuminate with Diagnostic Trouble Codes (DTCs) P1380,.P1381 or P1383 stored in continuous memory on some vehicles. Driveability concerns may or may not be present. This may be caused by engine oil contamination.
ACTION
Refer to the following Service Procedure for diagnostic and repair procedures.
SERVICE PROCEDURE
The Variable Cam Timing (VCT) sprocket retards the exhaust camshaft up to 30 degrees producing exhaust valve overlap. This controlled overlap allows exhaust gases to enter the combustion chamber, effectively providing Exhaust Gas Recirculation (EGR) flow to the engine without the use of an EGR valve. The VCT holds the exhaust camshaft fully advanced by internal spring pressure in its normal, uncontrolled state. For example, if the VCT solenoid is unplugged. When retard is commanded by the Powertrain Control Module (PCM), engine oil pressure is directed through the VCT solenoid to overcome internal return spring force in the VCT sprocket.
Parameter Identification Displays (PIDS) Relevant To VCT:
CAMDCR (0 to 99%) is the on-time of the VCT solenoid as requested by the PCM.
CAMERR (0 to 30 Degrees) is how many degrees the exhaust cam is "out" from the requested position. Values "+" mean the cam is not retarded enough and values "-" indicate the cam is over retarded.
RCAM (-15 to +45 Degrees) represents actual position of the cam relative to the crankshaft.
Normal PID Values (Approximate):
Warm idle (exhaust cam fully advanced/no EGR effect): CAMDCR = 0%, CAMERR 0 degrees, RCAM = -15 degrees.
Warm cruise: CAMDCR = 50%, CAMERR = 0 degrees, RCAM = 40 degrees.
DTC(s):
P1380 - VCT Solenoid Malfunction: Indicates a VCT circuit failure between the PCM and the VCT solenoid, or possible VCT solenoid failure. Consult the appropriate Electrical and Vacuum Troubleshooting Manual (EVTM) for circuit location and description.
P1381 - VCT Over-Advanced: Indicates the exhaust camshaft would not retard to the position requested by the PCM.
P1383 - VCT Over-Retarded: Indicates the exhaust camshaft would not advance (return) to the position requested by the PCM.
Diagnosing DTCs P1380, P1381, Or P1383:
P1380 and P1381 stored together: Possible open VCT solenoid or circuit between the PCM and VCT. These conditions would not allow the cam to retard as requested by the PCM.
P1381 or P1383: Must NOT be set together and ONLY in Continuous Memory for the following to be accurate: Possible VCT sprocket is sticking intermittently while driving. Exhaust camshaft is out of desired position as monitored by the PCM.
This condition could be caused by engine oil contamination. Consult TSB 99-13-8 for further diagnostics.
P1381: Single DTC set. Must be a hard fault. Monitor the following PIDs, checking for these readings: CAMDCR reads 99%, CAMERR reads a high "+" value while driving, and RCAM reads -15% at idle. This condition may indicate a sticking VCT sprocket which is retarding the exhaust camshaft. TSB 99-13-8 may remedy this concern. If concern persists after the TSB flushing procedure, replace the VCT sprocket. Refer to Section 303-01 in the appropriate Workshop Manual for VCT sprocket replacement. If RCAM is ABOVE -15 deg at idle, suspect base cam timing. Check and adjust the timing belt per Section 303-01 in the appropriate Workshop Manual.
P1383: Single DTC set/hard fault/rough running engine. If RCAM reads +45 at idle, VCT sprocket is stuck in the retarded position (very unlikely due to return spring force acting on VCT sprocket). VCT flush procedure from TSB 99-13-8 may be effective. If concern persists, replace VCT solenoid. Refer to Section 303-01 in the appropriate Workshop Manual for VCT solenoid replacement. If RCAM reads other than +45 at idle, suspect base cam timing. Check and adjust the timing belt per Section 303-01 in the appropriate Workshop Manual.
PART NUMBER PART NAME
F8CZ-6L713-AA Variable Camshaft Timing Solenoid
F8CZ-6256-AA Variable Camshaft Timing Sprocket
F8CZ-6M282-AA Sprocket Bolt
OTHER APPLICABLE ARTICLES: 99-13-8
WARRANTY STATUS: Eligible Under The Provisions Of Bumper To Bumper Warranty Coverage And Emissions Warranty Coverage
OPERATION DESCRIPTION TIME
000307A Replace VCT 1.9 Hrs.
Solenoid/Sprocket (Not To
Be Used With Operations
"A" Or "C"
000307B Replace VCT Sprocket 1.9 Hrs.
Only (Not To Be Used
With Operations "A" Or
"C"
000307C Check And Adjust Base 1.9 Hrs.
Timing (Not To Be Used
With Operations "A" Or
"B"
DEALER CODING
CONDITION
BASIC PART NO. CODE
6256 69
6L713 69
OASIS CODES: 206000, 499000, 690000, 698298