Removal
Special Tools:
1. General instructions
- The following instructions apply to the CD4E automatic transaxle with the 2.5L engine.
- The locations of engine mountings and engine support insulators are described looking from the automatic transaxle to the engine.
2. Standard preparatory measures
- Move the selector lever to "D" position.
- Move a note of the radio keycode.
- Make a note of the preset radio stations.
3. Remove the battery tray.
4. Fix the radiator in position on both sides (left hand side shown).
5. Remove the Air Cleaner (ACL).
6. NOTE: Use an Allen key to stop the piston rod from turning.
Loosen the suspension strut locknuts five turns (right-hand side shown).
7. Loosen the wheel nuts to both front wheels.
8. Disconnect the electrical connections.
1 Ground cable
2 Automatic transaxle control
3 Transmission Range (TR) switch
4 Wiring harness retaining clip
9. Remove the water pump cover.
1 Disconnect the engine coolant hose.
2 Remove the bolts.
3 Remove the water pump cover.
10. NOTE: Starter motor to remain in vehicle temporary.
Remove the starter motor bolts.
11. Install the special tools.
12. Remove the rear transaxle support insulator bracket.
13. NOTE: Ground lead.
Remove the upper bellhousing bolts (MY '99 four bolts).
14. Disconnect the selector cable from the transaxle.
1 Bracket
2 Selector lever selector cable
15. Raise and support the vehicle.
16. Remove both front wheels.
17. Drain the automatic transmission fluid.
- Place suitable pan under the transaxle.
- Retighten the drain plug.
18. Remove radiator splash shield.
- Remove the bolts and clips.
19. Remove the right-hand fender splash shields.
20. NOTE: Rotate bumper bracket forward.
Remove the bumper bracket on both side from sub-frame (left-hand side shown).
Vehicles With Air Conditioning
21. Remove the suction accumulator bracket bolts.
All Vehicles
22. Disconnect the Heated Oxygen Sensor (H02S) electrical connector.
- Separate the cable ties.
23. Disconnect the Turbine Shaft Speed (TSS) sensor electrical connector (shown from below).
- Unclip the cable.
24. Disconnect the Output Shaft Speed (OSS) sensor electrical connector.
25. CAUTION: Overbending of the flexible pipe may cause damage resulting in failure.
Remove the flexible pipe from the exhaust manifold.
- Remove the gaskets.
26. Remove the flexible pipe and the TWC continuation.
- Discard the gaskets.
27. CAUTION: Do not damage boot and ABS sensor ring.
Disconnect the lower suspension arm ball joints and the stabilizer link rods (right-hand side shown).
- Disconnect the ABS wiring harness bracket from the suspension strut.
28. Raise the automatic transaxle assembly slightly using the Transmission Jack .
29. Remove the left-hand engine support insulator center bolt.
30. Remove the steering gear heat shield.
31. Using the special tool, remove the steering gear (two bolts) and tie it up (left-hand side shown).
32. Disconnect the power steering hoses from the subframe (one nut and two bolts).
33. Remove the steering intermediate shaft from the steering gear.
34. Remove the transaxle cooler line brackets.
- Reposition the suction accumulator (A/C), if equipped.
35. CAUTION: Support the subframe using Rotunda Powertrain Lift. Place wooden block approximately one metre (40 inches) in length secured to lift under subframe.
Remove the sub-frame.
36. Remove the right-hand roll restrictor center bolt.
37. CAUTION: Do not loosen connector cooler inlet to transaxle.
Remove the lower transaxle cooling tube.
- Close the hole with suitable stuffing.
38. CAUTION: Do not loosen connector cooler inlet to transaxle.
Remove the upper transaxle cooling lines.
- Unclip transaxle cooling line from hold down.
- Close the hole with a suitable stuffing.
CAUTION: To avoid damage to joints and boots, do not bend the inner halfshaft joint by more than 18 degrees, the outer one by not more than 45 degrees.
39. Using the special tools, disconnect the left-hand halfshaft.
40. Pull out the left-hand halfshaft and tie it up.
41. Remove the right-hand halfshaft and intermediate shaft.
- Secure the right-hand halfshaft out of the way with mechanics wire.
42. NOTE: Discard the nuts.
Remove the torque converter rubber and the tour torque converter nuts.
- Remove rubber cover to gain access to the torque converter nuts.
- Rotate the torque converter to gain access to remaining nuts.
44. Install the Hi-Lift Transmission Jack and CD4E transaxle adapter.
- Secure with the Retaining straps.
45. Remove the lower bellhousing bolts.
46. Remove the front bellhousing bolts.
47. Open clamp and disconnect the main control cover vent tube.
48. CAUTION: The torque converter is heavy. Install the special tool before lowering the transaxle.
Install the special tool.
50. Lower the transaxle.