Deactivation and Reactivation
SPECIAL TOOL(S)
DEACTIVATION
WARNING:
- ALWAYS WEAR SAFETY GLASSES WHEN REPAIRING AN AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) VEHICLE AND WHEN HANDLING AN AIR BAG MODULE. THIS WILL REDUCE THE RISK OF INJURY IN THE EVENT OF AN ACCIDENTAL DEPLOYMENT.
- THE BELT AND BUCKLE ASSEMBLY PRETENSIONER IS A PYROTECHNIC DEVICE. ALWAYS WEAR SAFETY GLASSES WHEN REPAIRING AN AIR BAG EQUIPPED VEHICLE AND WHEN HANDLING A BELT AND BUCKLE ASSEMBLY PRETENSIONER.
- AFTER DEPLOYMENT, THE AIR BAG SURFACE CAN CONTAIN DEPOSITS OF SODIUM HYDROXIDE, A PRODUCT OF THE GAS GENERANT COMBUSTION THAT IS IRRITATING TO THE SKIN. WASH YOUR HANDS WITH SOAP AND WATER AFTERWARDS.
- NEVER PROBE THE CONNECTORS ON THE AIR BAG MODULE. DOING SO CAN RESULT IN AIR BAG DEPLOYMENT, WHICH CAN RESULT IN PERSONAL INJURY.
- THE BELT AND BUCKLE ASSEMBLY PRETENSIONER IS A PYROTECHNIC DEVICE. NEVER PROBE THE CONNECTORS ON THE BELT AND BUCKLE ASSEMBLY PRETENSIONERS. DOING SO COULD RESULT IN BELT AND BUCKLE ASSEMBLY PRETENSIONER OR AIR BAG DEPLOYMENT AND COULD RESULT IN PERSONAL INJURY.
- AIR BAG MODULES WITH DISCOLORED OR DAMAGED TRIM COVERS MUST BE INSTALLED NEW, NOT REPAINTED.
- THE RESTRAINT SYSTEM DIAGNOSTIC TOOL IS FOR RESTRAINT SYSTEM SERVICE ONLY. REMOVE FROM VEHICLE PRIOR TO ROAD USE. FAILURE TO REMOVE COULD RESULT IN INJURY AND POSSIBLE VIOLATION OF VEHICLE SAFETY STANDARDS.
NOTE:
- If a seat equipped with a seat mounted side airbag and/or a safety belt pretensioner (if equipped) system is being serviced the airbag system must be deactivated.
- Restraint system diagnostic tools MUST be installed under the seats in the side airbag and safety belt pretensioner (if equipped) to floor connectors.
- Diagnostics or repairs are not to be performed on a side airbag system and/or a safety belt pretensioner (if equipped) system with the seats in the vehicle. Prior to attempting to diagnose/repair the side airbag system and/or a safety belt pretensioner (if equipped) system the seats must be removed from the vehicle and the restraint system diagnostic tools must be installed in the side airbag and the safety belt pretensioner (if equipped) connectors at the floor connectors. The restraint system diagnostic tools must be removed prior to operating the vehicle over the road.
- Diagnostics may be performed on seat systems other than the side airbag or the safety belt pretensioner (if equipped) system (lumbar, climate controlled, heated, power seat track) with the seat installed in the vehicle as long as the restraint system diagnostic tools are installed under the seats in the side airbag and safety belt pretensioner to floor connectors.
- After diagnosing/repairing a seat system the restraint system diagnostic tools must be removed before operating the vehicle over the road.
- Repair is made by installing a new part only. If the new part does not correct the condition, install the original part and perform the diagnostic procedure again.
1. Disconnect the battery ground cable and wait at least one minute.
WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE REPAIRING OR REPLACING ANY FRONT OR SIDE AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) COMPONENTS AND BEFORE SERVICING, REPLACING, ADJUSTING OR STRIKING COMPONENTS NEAR THE FRONT OR SIDE AIR BAG SENSORS, SUCH AS DOORS, INSTRUMENT PANEL, CONSOLE, DOOR LATCHES, STRIKERS, SEATS AND HOOD LATCHES.
PLEASE REFER TO THE APPROPRIATE COMPONENT OR SYSTEM TO DETERMINE LOCATION OF THE FRONT AIR BAG SENSORS.
THE SIDE AIR BAG SENSORS ARE LOCATED AT OR NEAR THE BASE OF THE B-PILLAR.
TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY GROUND CABLE AND WAIT AT LEAST ONE MINUTE. BE SURE TO DISCONNECT AUXILIARY BATTERIES AND POWER SUPPLIES (IF EQUIPPED).
2. Remove the steering column opening lower finish panel.
1 Remove the screws.
2 Position the parking brake release assembly aside.
3 Pull out at the top to release the retaining clips and remove the steering column opening lower finish panel.
3. Remove the steering column opening lower reinforcement.
1 Remove the five bolts.
2 Remove the steering column opening lower reinforcement.
4. Remove the LH lower instrument panel insulator.
1 Remove the pin-type retainers.
2 Remove the courtesy lamp.
3 Slide and remove the LH lower instrument panel insulator out of the front retaining bracket.
5. Pushing in on the release tab, disconnect the clockspring electrical connector at the base of the steering column.
6. Attach the restraint system diagnostic tool to the vehicle harness side of the clockspring electrical connector.
7. Separate the trim panel.
- Slide the trim panel slightly to the right aligning the keyway.
- Pull out, separating the trim panel from the instrument panel.
8. Remove the trim panel.
1 Disconnect the rear window defrost switch electrical connector.
2 Disconnect the clock electrical connector.
3 Remove the trim panel.
9. Open the glove compartment. Disconnect the glove compartment isolator.
10. While pushing in on the two glove compartment door tabs, position the glove compartment downward.
11. Through the glove compartment opening, remove the passenger air bag module bolts.
12. Separate the passenger air bag module from the instrument panel.
1 Remove the passenger air bag module bolts.
2 Placing one hand in the glove box opening, push the passenger air bag module out from the instrument panel.
13. Remove the passenger air bag module.
1 Push in on the retaining tab.
2 Disconnect the passenger air bag module electrical connector.
3 Remove the passenger air bag module.
14. Attach the restraint system diagnostic tool to the vehicle harness side of the passenger air bag electrical connector.
15. Connect the battery ground cable.
16. Move the front seats to their most forward position.
17. Disconnect the battery ground cable and wait at least one minute.
WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE REPAIRING OR REPLACING ANY FRONT OR SIDE AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) COMPONENTS AND BEFORE SERVICING, REPLACING, ADJUSTING OR STRIKING COMPONENTS NEAR THE FRONT OR SIDE AIR BAG SENSORS, SUCH AS DOORS, INSTRUMENT PANEL, CONSOLE, DOOR LATCHES, STRIKERS, SEATS AND HOOD LATCHES.
PLEASE REFER TO THE APPROPRIATE COMPONENT OR SYSTEM TO DETERMINE LOCATION OF THE FRONT AIR BAG SENSORS.
THE SIDE AIR BAG SENSORS ARE LOCATED AT OR NEAR THE BASE OF THE B-PILLAR.
TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY GROUND CABLE AND WAIT AT LEAST ONE MINUTE. BE SURE TO DISCONNECT AUXILIARY BATTERIES AND POWER SUPPLIES (IF EQUIPPED).
18. Remove the passenger side front door scuff plate.
19. Remove the passenger side rear door scuff plate.
20. Remove the passenger side B-pillar weather-stripping.
21. Remove the passenger side safety belt anchor bolt cover.
22. Remove the bolt and the passenger side safety belt anchor.
23. Pull out to release the retaining clips and remove the passenger side B-pillar lower trim panel.
24. Pushing in on the release the tab, disconnect the passenger safety belt retractor pretensioner electrical connector.
25. Attach the restraint system diagnostic tool to the vehicle harness side of the passenger safety belt retractor pretensioner electrical connector.
26. Remove the driver side front door scuff plate.
27. Remove the driver side rear door scuff plate.
28. Remove the driver side B-pillar weather-stripping.
29. Remove the driver side safety belt anchor bolt cover.
30. Remove the bolt and the driver side safety belt anchor.
31. Pull out to release the retaining clips and remove the driver side B-pillar lower trim panel.
32. Pushing in on the release tab, disconnect the driver safety belt retractor pretensioner electrical connector.
33. Attach the restraint system diagnostic tool to the vehicle harness side of the driver safety belt retractor pretensioner electrical connector.
34. Connect the battery ground cable.
35. With the restraint system diagnostic tools installed at all deployable devices, prove out the supplemental restraint system (SRS).
36. Disconnect the battery ground cable and wait at least one minute.
REACTIVATION
WARNING: TO REDUCE THE RISK OF SERIOUS PERSONAL INJURY, READ AND FOLLOW ALL WARNINGS, CAUTIONS, AND NOTES AT THE BEGINNING OF THE DEACTIVATION PROCEDURE.
1. Disconnect the battery ground cable and wait at least one minute.
2. Remove the restraint system diagnostic tool from the driver safety belt retractor pretensioner electrical connector.
3. Connect the driver safety belt retractor pretensioner electrical connector.
4. Align the driver side B-pillar lower trim panel and push in, seating the retaining clips.
5. Position the driver side safety belt anchor. Install the bolt.
6. Install the driver side safety belt anchor bolt cover.
7. Install the driver side B-pillar weather-stripping.
8. Install the driver side rear door scuff plate.
9. Install the driver side front door scuff plate.
10. Remove the restraint system diagnostic tool from the passenger safety belt retractor pretensioner electrical connector.
11. Connect the passenger safety belt retractor pretensioner electrical connector.
12. Align the passenger side B-pillar lower trim panel and push in, seating the retaining clips.
13. Position the passenger safety belt anchor. Install the bolt.
14. Install the passenger side safety belt anchor bolt cover.
15. Install the passenger side B-pillar weather-stripping.
16. Install the passenger side rear door scuff plates.
17. Install the passenger side front door scuff plate.
18. Connect the battery ground cable.
19. Position the front seats rearward.
20. Disconnect the battery ground cable and wait at least one minute.
WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE REPAIRING OR REPLACING ANY FRONT OR SIDE AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) COMPONENTS AND BEFORE SERVICING, REPLACING, ADJUSTING OR STRIKING COMPONENTS NEAR THE FRONT OR SIDE AIR BAG SENSORS, SUCH AS DOORS, INSTRUMENT PANEL, CONSOLE, DOOR LATCHES, STRIKERS, SEATS AND HOOD LATCHES.
PLEASE REFER TO THE APPROPRIATE COMPONENT OR SYSTEM TO DETERMINE LOCATION OF THE FRONT AIR BAG SENSORS.
THE SIDE AIR BAG SENSORS ARE LOCATED AT OR NEAR THE BASE OF THE B-PILLAR.
TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY GROUND CABLE AND WAIT AT LEAST ONE MINUTE. BE SURE TO DISCONNECT AUXILIARY BATTERIES AND POWER SUPPLIES (IF EQUIPPED).
21. Remove the restraint system diagnostic tool from the passenger air bag module electrical connector.
22. Make sure the J-clips on the back of the passenger air bag module are fully seated into the slots.
23. Position the passenger air bag module to the instrument panel. Connect the passenger air bag module electrical connector.
24. Install the passenger air bag module into the instrument panel.
1 Install the passenger air bag module into the instrument panel.
2 Install the bolts.
25. Through the glove compartment opening, install the passenger air bag module bolts.
26. Install the trim panel.
1 Connect the rear window defrost switch electrical connector.
2 Connect the clock electrical connector.
3 Align the retaining clips, slide the trim panel to the left and push in, seating the retaining clips.
27. Connect the glove compartment isolator. Close the glove compartment.
28. Remove the restraint system diagnostic tool from the clockspring electrical connector.
29. Connect the clockspring electrical connector at the base of the steering column.
30. Install the LH lower instrument panel insulator.
1 Install the courtesy lamp.
2 Slide the LH lower instrument panel insulator into the front retaining bracket (not shown).
3 Install the pin-type retainers.
31. Position the steering column opening lower reinforcement. Install the bolts.
32. Install the steering column opening lower finish panel.
1 Align the steering column opening lower finish panel and push in, seating the retaining clips.
2 Position the parking brake release assembly.
3 Install the screws.
33. Connect the battery ground cable.
34. With all the restraint system diagnostic tools removed, prove out the supplemental restraint system (SRS).
WARNING: THE RESTRAINT SYSTEM DIAGNOSTIC TOOL IS FOR RESTRAINT SYSTEM SERVICE ONLY. REMOVE FROM VEHICLE PRIOR TO ROAD USE. FAILURE TO REMOVE COULD RESULT IN INJURY AND POSSIBLE VIOLATION OF VEHICLE SAFETY STANDARDS.
35. Check the active restraint system for correct operation.