Rear View Mirrors - Interior
Rear View Mirrors - Interior
Pinpoint Tests
Pinpoint Test F: The Auto-Dimming Mirror Does Not Operate Correctly
Refer to Wiring Diagram Set 124, Power Mirrors for schematic and connector information. Diagrams By Number
Normal Operation
The interior auto-dimming mirror receives power from circuit CBP02 (GN) and ground from circuit GD139 (BK/YE). If equipped with a LH exterior auto-dimming mirror, and the auto-dimming feature is activated, voltage is sent from the interior mirror to the LH exterior mirror though circuit LRD12 (BU/GY). Ground for the LH exterior mirror is provided by the interior mirror through circuit RRD12 (BN). When the vehicle is placed in REVERSE, voltage is sent to the interior mirror through circuit CBP12 (GN/WH) and the interior mirror will turn the dimming feature off. There are 2 photoelectric sensors: one in the front of the interior rear view mirror and one mounted on the glass side of the mirror. If the sensors are blocked, the interior auto-dimming mirror might not work correctly. Always verify both sensors are not physically blocked before attempting to diagnose auto-dimming mirror concerns.
This pinpoint test is intended to diagnose the following:
- Fuse
- Wiring, terminals or connectors
- Interior auto-dimming mirror
- LH exterior mirror glass
- LH exterior mirror
PINPOINT TEST F: THE AUTO-DIMMING MIRROR DOES NOT OPERATE CORRECTLY
NOTE: If the Transmission Range (TR) sensor is malfunctioning and the backup lamps are on all the time or do not turn on, the auto-dimming interior mirror will not darken or return to normal view.
-------------------------------------------------
F1 CHECK THE OPERATION OF THE BACKUP LAMPS
- Ignition ON.
- Move the selector lever through the entire range.
- Do the backup lamps illuminate only in REVERSE?
Yes
MKZ only: If the LH exterior mirror only is always dim, REPAIR circuit LRD12 (BU/GY) for a short to voltage. TEST the system for normal operation.
MKZ only: If the LH exterior mirror only does not dim correctly, GO to F10 .
MKZ only: If the interior mirror only does not dim correctly and the LH exterior mirror does dim correctly, INSTALL a new interior mirror, REFER to Auto-Dimming Interior Mirror Auto-Dimming Interior Mirror. TEST the system for normal operation.
MKZ only: If the LH exterior mirror and interior mirror does not dim correctly, GO to F2 .
Fusion and Milan only: If the interior mirror does not operate correctly, GO to F2 .
No
REFER to Backup Lamp to diagnose the backup lamps. Testing and Inspection
-------------------------------------------------
F2 VERIFY THAT THE FORWARD AND REARWARD FACING SENSORS ARE NOT BLOCKED
- Visually verify that the forward and rearward facing sensors are not blocked. Sources of blockage can include:
- stickers, window decals or tags.
- fold-down screens for TVs or DVD players.
- non-OEM window tinting.
- Were either of the sensors blocked?
Yes
If possible, REMOVE the blockage. TEST the system for normal operation. If the blockage cannot be removed, REVIEW the operation of the interior auto-dimming mirror with the customer.
No
GO to F3.
-------------------------------------------------
F3 CHECK THE OPERATION OF THE INTERIOR AUTO-DIMMING MIRROR - DAYLIGHT CONDITIONS
- Ignition ON.
- Use a bright lamp to simultaneously illuminate the forward-facing sensor and the rearward-facing sensor. The mirror should adjust to a high reflectance mode (mirror will be clear).
- Does the mirror adjust to the high reflectance (clear) mode?
Yes
GO to F4.
No
INSTALL a new interior mirror. REFER to Auto-Dimming Interior Mirror Auto-Dimming Interior Mirror. TEST the system for normal operation.
-------------------------------------------------
F4 CHECK THE OPERATION OF THE INTERIOR AUTO-DIMMING MIRROR - NIGHTTIME CONDITIONS WITH GLARE
- Ignition ON.
- Simulate nighttime conditions with glare:
NOTE: Covering the sensor with a finger or hand is not adequate.
- Cover the forward-facing sensor with black electrical tape or other dark material.
- Illuminate the rearward-facing sensor. The mirror should darken to a lower reflectance mode.
- Did the mirror darken to a lower reflectance (darker) mode?
Yes
GO to F5.
No
GO to F7.
-------------------------------------------------
F5 CHECK THE OPERATION OF THE INTERIOR AUTO-DIMMING MIRROR - NIGHTTIME CONDITIONS WITHOUT GLARE
- Ignition ON.
- Simulate nighttime conditions without glare:
NOTE: Covering the sensor with a finger or hand is not adequate.
- Cover the forward-facing sensor with black electrical tape or other dark material.
- Cover the rearward-facing sensor. The mirror should adjust to the high reflectance mode.
- Did the mirror adjust to the high reflectance (clear) mode?
Yes
GO to F6.
No
GO to F7.
-------------------------------------------------
F6 CHECK THE OPERATION OF THE INTERIOR AUTO-DIMMING MIRROR - NIGHTTIME CONDITIONS WITH THE VEHICLE IN REVERSE
- Ignition ON.
- Simulate nighttime conditions with glare:
NOTE: Covering the sensor with a finger or hand is not adequate.
- Cover the forward-facing sensor with black electrical tape or other dark material.
- Illuminate the rearward-facing sensor.
- Select REVERSE.
- Did the mirror adjust to a high reflectance (clear) mode?
Yes
The system is operating normally at this time. REVIEW operation of the interior auto-dimming mirror feature with the customer.
No
GO to F7.
-------------------------------------------------
F7 CHECK CIRCUIT CBP02 (GN) FOR VOLTAGE
- Ignition OFF.
- Disconnect: Interior Mirror C911 (without microphone) or C9030 (with microphone).
- Ignition ON.
- Without microphone: Measure the voltage between interior mirror C911-1, circuit CBP02 (GN), harness side and ground.
- With microphone: Measure the voltage between interior mirror C9030-1, circuit CBP02 (GN), harness side and ground.
- Is the voltage greater than 10 volts?
Yes
GO to F8.
No
VERIFY that Smart Junction Box (SJB) fuse 12 (7.5A) is OK. If OK, REPAIR the circuit. If not OK, REFER to the Wiring Diagrams to identify the possible causes of the circuit short. TEST the system for normal operation.
-------------------------------------------------
F8 CHECK CIRCUIT GD139 (BK/YE) FOR AN OPEN
- Ignition OFF.
- Without microphone: Measure the resistance between interior mirror C911-3, circuit GD139 (BK/YE), harness side and ground.
- With microphone: Measure the resistance between interior mirror C9030-10, circuit GD139 (BK/YE), harness side and ground.
- Is the resistance less than 10 ohms?
Yes
GO to F9.
No
REPAIR the circuit. TEST the system for normal operation.
-------------------------------------------------
F9 CHECK CIRCUIT CBP12 (GN/WH) FOR VOLTAGE
- Ignition ON.
- Select REVERSE.
- Without microphone: Measure the voltage between interior mirror C911-2, circuit CBP12 (GN/WH), harness side and ground.
- With microphone: Measure the voltage between interior mirror C9030-3, circuit CBP12 (GN/WH), harness side and ground.
- Is the voltage greater than 10 volts?
Yes
INSTALL a new interior mirror. REFER to Auto-Dimming Interior Mirror Auto-Dimming Interior Mirror. TEST the system for normal operation.
No
REPAIR the circuit. TEST the system for normal operation.
-------------------------------------------------
F10 CHECK CIRCUIT LRD12 (BU/GY) FOR VOLTAGE
- Ignition OFF.
- Disconnect: LH Exterior Mirror C522.
- Ignition ON.
- Simulate night time conditions with glare:
NOTE: Covering the sensor with a finger or hand is not adequate.
- Cover the forward-facing sensor with black electrical tape or other dark material.
- Illuminate the rearward-facing sensor. The mirror should darken to a lower reflectance mode.
- Measure the voltage between LH exterior mirror C522-9, circuit LRD12 (BU/GY), harness side and ground.
- Is the voltage greater than 1 volt?
Yes
GO to F11.
No
GO to F13.
-------------------------------------------------
F11 CHECK CIRCUIT RRD12 (BN) FOR GROUND
- Measure the resistance between LH exterior mirror C522-8, circuit RRD12 (BN), harness side and ground.
- Is the resistance less than 15 ohms?
Yes
CHECK the LH exterior mirror jumper harness between the vehicle harness and the exterior mirror glass for shorted or open circuits and damaged or pushed-out pins. If the jumper harness is not OK, REPAIR the jumper harness. If the jumper harness cannot be repaired, INSTALL a new LH exterior mirror. REFER to Exterior Mirror Exterior Mirror. If the jumper harness is OK, INSTALL a new LH exterior mirror glass. REFER to Exterior Mirror Glass Exterior Mirror Glass. TEST the system for normal operation.
No
GO to F12.
-------------------------------------------------
F12 CHECK CIRCUIT RRD12 (BN) FOR AN OPEN
- Ignition OFF.
- Disconnect: Interior Mirror C911 (without microphone) or C9030 (with microphone).
- Without microphone: Measure the resistance between interior mirror C911-5, circuit RRD12 (BN), harness side and LH exterior mirror C522-8, circuit RRD12 (BN), harness side.
- With microphone: Measure the resistance between interior mirror C9030-7, circuit RRD12 (BN), harness side and LH exterior mirror C522-8, circuit RRD12 (BN), harness side.
- Is the resistance less than 5 ohms?
Yes
INSTALL new interior mirror. REFER to Auto-Dimming Interior Mirror Auto-Dimming Interior Mirror. TEST the system for normal operation.
No
REPAIR the circuit. TEST the system for normal operation.
-------------------------------------------------
F13 CHECK CIRCUIT LRD12 (BU/GY) FOR AN OPEN
- Ignition OFF.
- Disconnect: Interior Mirror C911 (without microphone) or C9030 (with microphone).
- Without microphone: Measure the resistance between LH exterior mirror C522-9, circuit LRD12 (BU/GY), harness side and interior mirror C911-4, circuit LRD12 (BU/GY), harness side.
- With microphone: Measure the resistance between LH exterior mirror C522-9, circuit LRD12 (BU/GY), harness side and interior mirror C9030-8, circuit LRD12 (BU/GY), harness side.
- Is the resistance less than 5 ohms?
Yes
GO to F14.
No
REPAIR the circuit. TEST the system for normal operation.
-------------------------------------------------
F14 CHECK CIRCUIT LRD12 (BU/GY) FOR A SHORT TO GROUND
- Without microphone: Measure the resistance between interior mirror C911-4, circuit LRD12 (BU/GY), harness side and ground.
- With microphone: Measure the resistance between interior mirror C9030-8, circuit LRD12 (BU/GY), harness side and ground.
- Is the resistance greater than 10,000 ohms?
Yes
INSTALL new interior mirror. REFER to Auto-Dimming Interior Mirror Auto-Dimming Interior Mirror. TEST the system for normal operation.
No
REPAIR the circuit. TEST the system for normal operation.
-------------------------------------------------