Procedures

Fuel Tank Draining - 3.0L All Wheel Drive (AWD)





WARNING: Do not smoke, carry lighted tobacco or have an open flame of any type when working on or near any fuel-related component. Highly flammable mixtures are always present and may be ignited. Failure to follow these instructions may result in serious personal injury.

WARNING: Do not carry personal electronic devices such as cell phones, pagers or audio equipment of any type when working on or near any fuel-related component. Highly flammable mixtures are always present and may be ignited. Failure to follow these instructions may result in serious personal injury.

WARNING: When handling fuel, always observe fuel handling precautions and be prepared in the event of fuel spillage. Spilled fuel may be ignited by hot vehicle components or other ignition sources. Failure to follow these instructions may result in serious personal injury.

WARNING: Always disconnect the battery ground cable at the battery when working on an evaporative emission (EVAP) system or fuel-related component. Highly flammable mixtures are always present and may be ignited. Failure to follow these instructions may result in serious personal injury.

NOTE: For vehicles with an inaccurate or inoperable fuel gauge, follow the instructions for draining a fuel tank with more than one-half of a tank of fuel.

All vehicles

1. Release the fuel system pressure. For additional information, refer to Fuel System Pressure Release Service and Repair.

2. Disconnect the battery ground cable. For additional information, refer to Battery, Mounting and Cables Battery Disconnect.

Vehicles with more than one-half of a tank of fuel

NOTE: The Easy Fuel(TM) (capless) fuel tank filler pipe on 3.0L vehicles have an anti-siphon grate that will not allow a fuel drain tube to penetrate the fuel tank and requires the following steps to drain the fuel.

3. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Jacking and Lifting Service and Repair.

4. NOTE: Index-mark the fuel tank filler pipe hose and the clamp prior to removal for correct installation.

Release the clamp and disconnect the hose from the fuel tank filler pipe.

- To install, tighten to 4 Nm (35 lb-in).





5. Insert a semi-rigid fuel drain tube into the fuel tank filler pipe hose until it enters the fuel tank.





6. NOTE: This step is to remove approximately one-half tank of the fuel from a completely full fuel tank, lowering the fuel level below the Fuel Pump (FP) module mounting flange.

Attach the Fuel Storage Tanker to the fuel drain tube and remove one-half (approximately 9 gallons) of fuel from the tank.

All vehicles

7. Remove the rear seat lower cushion. For additional information, refer to Seating Seat Cushion - Rear.

8. Remove the 3 screws and the FP module access cover.





9. NOTE: Clean the FP module connections, couplings, flange surfaces and the immediate surrounding area of any dirt or foreign material.

Disconnect the FP module electrical connector.





10. NOTE: Place absorbent toweling in the immediate surrounding area in case of fuel spillage.

Disconnect the fuel tube-to-FP module quick connect coupling. For additional information, refer to Fuel System - General Information Quick Connect Coupling.





11. NOTE: Make sure to install a new FP module O-ring seal.

Install the Fuel Tank Sender Unit Wrench and remove the FP module lock ring.

- Discard the FP module O-ring seal.





12. NOTICE: The Fuel Pump (FP) module must be handled carefully to avoid damage to the float arm.

Position the FP module aside and insert the tube from the Fuel Storage Tanker into the FP module aperture and drain as much fuel from the fuel tank as possible.





13. Remove the 3 screws and the fuel level sensor access cover.





14. NOTE: Clean the fuel level sensor electrical connector, flange surface and the immediate surrounding area of any dirt or foreign material.

Disconnect the fuel level sensor electrical connector.





15. NOTE: Place absorbent toweling in the immediate surrounding area in case of fuel spillage.

Release the lock tab and rotate the fuel level sensor counterclockwise approximately one-fourth turn, lift and position aside.





16. Insert the tube from the Fuel Storage Tanker into the fuel level sensor aperture and drain the remainder of the fuel from the fuel tank.