Operation CHARM: Car repair manuals for everyone.
Home >> Mercury >> 2011 >> Milan FWD V6-3.0L >> Repair and Diagnosis >> Body and Frame >> Seats >> Testing and Inspection >> Pinpoint Tests >> Pinpoint Test AS: DTC B2730

Pinpoint Test AS: DTC B2730




Seats

Pinpoint Test AS: DTC B2730

Refer to Wiring Diagram Set 119 (Fusion/Milan/MKZ, Fusion Hybrid, Milan Hybrid, MKZ Hybrid), Climate Controlled Seats for schematic and connector information. Diagrams By Number

Normal Operation

The Dual Climate Controlled Seat Module (DCSM) monitors seat backrest temperature while it supplies voltage and ground to both blower motors. The DCSM also supplies a variable voltage signal to control the blower speed. Cabin air enters the blower through a filter attached to the Thermo-Electric Device (TED) housing. Conditioned air exits the TED and flows through a manifold attached to the foam pad.

- DTC B2730 (Back Over-Temp Detected) - If the driver seat backrest TED temperature exceeds 85°C (185°F) in cool mode or 70°C (158°F) in heat mode for more than 34 seconds the DCSM will shut down the driver seat system and set.

This pinpoint test is intended to diagnose the following:
- Wiring, terminals or connectors
- Restricted backrest TED filter
- Crushed or restricted climate controlled seat manifold
- Backrest TED assembly


PINPOINT TEST AS: DTC B2730

NOTE: If a seat equipped with a seat mounted side air bag is being serviced, the Supplemental Restraint System (SRS) must be depowered. Refer to Supplemental Restraint System Supplemental Restraint System (SRS) Depowering and Repowering.

NOTE: The air bag warning lamp illuminates when the Restraints Control Module (RCM) fuse is removed and the ignition switch is ON. This is normal operation and does not indicate an SRS fault.

NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.

-------------------------------------------------
AS1 CHECK THE BACKREST BLOWER FOR AN OBSTRUCTION OR RESTRICTED FILTER

- Check the seat for any obstruction at the TED assembly and for a restricted filter.
- Is the filter clean and blower clear of any obstruction?

Yes
GO to AS2.

No
REMOVE the obstruction or CLEAN the filter. REPEAT the self-test. CLEAR the DTCs. TEST the system for normal operation.

-------------------------------------------------
AS2 CHECK OPERATION OF THE SEAT AND MONITOR SEAT TEMPERATURE USING THE SCAN TOOL

- Enter the following diagnostic mode on the scan tool: DataLogger - DCSM - PIDs.

- Seat cushion thermal electric device temperature (CSHTEMP)
- Seat back thermal electric device temperature (BK_TEMP)
- Start the engine.
- Operate the seat in high heat or high cool and monitor the seat operation. If a circuit fault is present, the DCSM will disable the seat.
- Monitor the cushion and backrest temperature PIDs while the seat is operating. The temperatures should be similar during operation.
- Does the seat operate and temperature PIDs indicate correct operation?

Yes
The system is operating correctly at this time. The fault may have occurred from incorrectly switching between heat and cool modes. REPEAT the self-test. CLEAR the DTCs.

No
If the seat is operational, but the backrest temperature increases greater than the cushion, GO to AS3.

If the seat does not operate, GO to AS4.

-------------------------------------------------
AS3 CHECK THE TED FOR CORRECT INSTALLATION AND FOR A CRUSHED CLIMATE CONTROLLED SEAT MANIFOLD

- Remove the seat backrest cover. Refer to Seat Backrest - Front Seat Backrest - Front.
- Check the TED and climate controlled seat manifold for damage, restriction and for correct installation.
- Is the TED correctly installed and the climate controlled seat manifold OK?

Yes
INSTALL a new backrest TED. REFER to Seat Backrest Thermo-Electric Device Seat Backrest Thermo-Electric Device. REPEAT the self-test. CLEAR the DTCs. TEST the system for normal operation.

No
CORRECTLY install the backrest TED or INSTALL a new climate controlled seat manifold. REPEAT the self-test. CLEAR the DTCs. TEST the system for normal operation.

-------------------------------------------------
AS4 CHECK THE TED THERMISTOR CIRCUIT FOR A SHORT TO GROUND

- Ignition OFF.
- Depower the SRS. Refer to Supplemental Restraint System (SRS) Depowering and Repowering in the General Procedures portion of Supplemental Restraint System Supplemental Restraint System (SRS) Depowering and Repowering.
- Disconnect: Driver Seat Side Air Bag C327.
- Disconnect: Passenger Seat Side Air Bag C313.
- Disconnect: DCSM C3305B.
- Disconnect: Backrest TED C3310.
- Measure the resistance between DCSM C3305B-9, circuit VHS35 (VT/OG), harness side and ground.




- Is the resistance greater than 10,000 ohms?

Yes
GO to AS5.

No
REPAIR the circuit. REPEAT the self-test. CLEAR the DTCs. TEST the system for normal operation.

DISCONNECT the battery ground cable. CONNECT driver seat side air bag module C327 and passenger seat side air bag module C313.

REPOWER the SRS. REFER to Supplemental Restraint System Supplemental Restraint System (SRS) Depowering and Repowering.

-------------------------------------------------
AS5 CHECK THE TED THERMISTOR CIRCUITS FOR A SHORT TOGETHER

- Measure the resistance between DCSM C3305B-9, circuit VHS35 (VT/OG), harness side and DCSM C3305B-10, circuit RHS15 (GY/BN), harness side.




- Is the resistance greater than 10,000 ohms?

Yes
GO to AS6.

No
REPAIR the circuit(s). REPEAT the self-test. CLEAR the DTCs. TEST the system for normal operation

DISCONNECT the battery ground cable. CONNECT driver seat side air bag module C327 and passenger seat side air bag module C313.

REPOWER the SRS. REFER to Supplemental Restraint System Supplemental Restraint System (SRS) Depowering and Repowering.

-------------------------------------------------
AS6 CHECK THE BLOWER CIRCUITS FOR AN OPEN

- Disconnect: DCSM C3305C.
- Measure the resistance between:
- DCSM C3305C-16, circuit CHS03 (GN/BN), harness side and backrest TED C3310-2, circuit CHS03 (GN/BN), harness side.
- DCSM C3305C-15, circuit CHS03 (GY/OG), harness side and backrest TED C3310-4, circuit RHS03 (GY/OG), harness side.
- DCSM C3305C-12, circuit VHS16 (BU/GN), harness side and backrest TED C3310-7, circuit VHS16 (BU/GN), harness side.




- Are the resistances less than 5 ohms?

Yes
INSTALL a new backrest TED. REFER to Seat Backrest Thermo-Electric Device Seat Backrest Thermo-Electric Device. REPEAT the self-test. CLEAR the DTCs. TEST the system for normal operation.

DISCONNECT the battery ground cable. CONNECT driver seat side air bag module C327 and passenger seat side air bag module C313.

REPOWER the SRS. REFER to Supplemental Restraint System Supplemental Restraint System (SRS) Depowering and Repowering.

No
REPAIR the circuit(s). TEST the system for normal operation. REPEAT the self-test. CLEAR the DTCs.

DISCONNECT the battery ground cable. CONNECT driver seat side air bag module C327 and passenger seat side air bag module C313.

REPOWER the SRS. REFER to Supplemental Restraint System Supplemental Restraint System (SRS) Depowering and Repowering.

-------------------------------------------------

pro multis · About Operation CHARM