Programming and Relearning
ConfigurationDESCRIPTION
CONFIGURATION has two functions as follows:
- READ CONFIGURATION is the function to confirm vehicle configuration of current BCM.
- WRITE CONFIGURATION is the function to write vehicle configuration on BCM.
CAUTION:
- When replacing BCM, you must perform WRITE CONFIGURATION with CONSULT-II.
- Complete the procedure of WRITE CONFIGURATION in order.
- If you set incorrect WRITE CONFIGURATION, incidents will occur.
- Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
READ CONFIGURATION PROCEDURE
CAUTION: If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be detected in self-diagnosis depending on control unit which carries out CAN communication.
1. With ignition switch OFF, connect CONSULT-II and CONSULT-II CONVERTER to data link connector and turn ignition switch ON.
2. Touch "START (NISSAN BASED VHCL)".
3. Touch "BCM" on "SELECT SYSTEM" screen.
If "BCM" is not indicated, go to GI-39, "CONSULT-II Data Link Connector (DLC) Circuit". Schematic
4. Touch "BCM" on "SELECT TEST ITEM" screen.
5. Touch "CONFIGURATION" on "SELECT DIAG MODE" screen.
6. Touch "A60" and "OK" on "VEHICLE SELECT" screen. For canceling, touch "CANCEL" on "VEHICLE SELECT" screen.
NOTE: Confirm vehicle model. Refer to "Model Variation" in Vehicle/Application and ID. Application and ID
7. Touch "READ CONFIGURATION" on "SELECT CONFIG ITEM" screen.
8. Configuration of current BCM is printed out automatically. A listing of manual setting items and auto setting items will be displayed. Auto setting items are preset and cannot be changed. Manual setting items can be set by using WRITE CONFIGURATION PROCEDURE. Refer to "WRITE CONFIGURATION PROCEDURE".
9. Touch "BACK" on "READ CONFIGURATION" screen.
WRITE CONFIGURATION PROCEDURE
CAUTION: If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be detected in self-diagnosis depending on control unit which carries out CAN communication.
1. With ignition switch OFF, connect CONSULT-II and CONSULT-II CONVERTER to data link connector and turn ignition switch ON.
2. Touch "START (NISSAN BASED VHCL)".
3. Touch "BCM" on "SELECT SYSTEM" screen.
If "BCM" is not indicated, go to GI-39, "CONSULT-II Data Link Connector (DLC) Circuit". Schematic
4. Touch "BCM" on "SELECT TEST ITEM" screen.
5. Touch "CONFIGURATION" on "SELECT DIAG MODE" screen.
6. Touch "A60" and "OK" on "VEHICLE SELECT" screen. For canceling, touch "CANCEL" on "VEHICLE SELECT" screen.
NOTE: Confirm vehicle model. Refer to "Model Variation" in Vehicle/Application and ID. Application and ID
7. Touch "WRITE CONFIGURATION" on "SELECT CONFIG ITEM" screen.
8. Touch "YES".
For canceling, touch "NO".
9. Set by touching selection on "WRITE CONFIGURATION" screen based on the following ITEM LIST.
Do not apply MODE3 or MODE4.
NOTE: Confirm vehicle model. Refer to "Model Variation" in Vehicle/Application and ID. Application and ID
10. Touch "CHNG SETTING" on "WRITE CONFIGURATION" screen.
CAUTION: Make sure to touch "CHNG SETTING" even if the indicated configuration of new BCM is same as the desirable configuration. If not, configuration which is set automatically by selecting vehicle model cannot be memorized.
11. Touch "OK" on "WRITE CONFIGURATION" screen.
If "CANCEL" is touched, it will return to previous screen.
12. Wait until the next screen during setting.
13. WRITE CONFIGURATION results are printed out automatically. Confirm "WRITE CONFIGURATION" is correctly executed by comparing sheet automatically printed out with applicable configuration list shown in step 9.
14. Touch "OK" on "WRITE CONFIGURATION" screen. WRITE CONFIGURATION is completed.