Programming and Relearning

Configuration

DESCRIPTION
CONFIGURATION has two functions as follows:
- READ CONFIGURATION is the function to confirm vehicle configuration of current BCM.
- WRITE CONFIGURATION is the function to write vehicle configuration on BCM.

CAUTION:
- When replacing BCM, you must perform WRITE CONFIGURATION with CONSULT-II.
- Complete the procedure of WRITE CONFIGURATION in order.
- If you set incorrect WRITE CONFIGURATION, incidents will occur.
- Configuration is different for each vehicle model. Confirm configuration of each vehicle model. Application and ID

READ CONFIGURATION PROCEDURE

CAUTION: If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be detected in self-diagnosis depending on control unit which carries out CAN communication.

1. With ignition switch OFF, connect CONSULT-II and CONSULT-II CONVERTER to data link connector and turn ignition switch ON.

2. Touch "START (NISSAN BASED VHCL)".

3. Touch "BCM" on "SELECT SYSTEM" screen. If "BCM" is not indicated, go to GI section. Refer to GI-41 "CONSULT-II Data Link Connector (DLC) Circuit". Schematic

4. Touch "BCM" on "SELECT TEST ITEM" screen.

5. Touch "CONFIGURATION" on "SELECT DIAG MODE" screen.

6. Touch "R51/D40/N51" and "OK" on "VEHICLE SELECT" screen.
For canceling, touch "CANCEL" on "VEHICLE SELECT" screen.

NOTE: Confirm vehicle model on IDENTIFICATION PLATE. Refer to �Model Variation" in GI section. Application and ID

7. Touch "READ CONFIGURATION" on "SELECT CONFIG ITEM" screen.

8. Configuration of current BCM is printed out automatically. A listing of manual setting items and auto setting items will be displayed. Auto setting items are preset and cannot be changed. Manual setting items can be set by using WRITE CONFIGURATION PROCEDURE. Refer to "WRITE CONFIGURATION PROCEDURE".

9. Touch "BACK" on "READ CONFIGURATION" screen.

WRITE CONFIGURATION PROCEDURE

CAUTION: If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be detected in self-diagnosis depending on control unit which carries out CAN communication.

1. With ignition switch OFF, connect CONSULT-II and CONSULT-II CONVERTER to data link connector and turn ignition switch ON.

2. Touch "START (NISSAN BASED VHCL)".

3. Touch "BCM" on "SELECT ITEM" screen. If "BCM" is not indicated, go to GI section to check CONSULT II data link connector (DLC) circuit. Refer to GI-41, "CONSULT-II Data Link Connector (DLC) Circuit". Schematic

4. Touch "BCM" on "SELECT TEST ITEM" screen.

5. Touch "CONFIGURATION" on "SELECT DIAG MODE" screen.

7. Touch "WRITE CONFIGURATION" on "SELECT CONFIG ITEM" screen.

8. Touch "YES".
For canceling, touch "NO".

9. Using the following flow chart, identify the correct model and configuration list. Confirm and/or change setting value for each item according to the configuration list.

Depending on CONSULT-II software version being used, some or all of the write configuration items shown in the following configuration lists may be displayed. If an item does not appear on the CONSULT-II "WRITE CONFIGURATION" screen(s), then it is an auto setting item and it cannot be manually set or changed.

NOTE: Confirm vehicle model on IDENTIFICATION PLATE. Refer to "Model Variation".

10. Touch "CHNG SETTING" on "WRITE CONFIGURATION" screen.

CAUTION: Make sure to touch "CHNG SETTING" even if the indicated configuration of brand-new BCM is same as the desirable configuration.
If not, configuration which is set automatically by selecting vehicle model cannot be memorized.

11. Touch "OK" on "WRITE CONFIGURATION" screen.
If "CANCEL" is touched, it will return to previous screen.

12. Wait until the next screen during setting.

13. WRITE CONFIGURATION results are printed out automatically.
Confirm "WRITE CONFIGURATION" is correctly executed by comparing sheet automatically printed out with applicable configuration list shown in step 9.

14. Touch "OK" on "WRITE CONFIGURATION" screen.
WRITE CONFIGURATION is completed.